Ryobi AP1301 Extension Cords, Electrical Connection, Speed and Wiring, Grounding Instructions

Page 8

ELECTRICAL

EXTENSION CORDS

Use only 3-wire extension cords that have 3-prong ground- ing plugs and 3-pole receptacles that accept the tool’s plug. When using a power tool at a considerable distance from the power source, use an extension cord heavy enough to carry the current that the tool will draw. An undersized extension cord will cause a drop in line voltage, resulting in a loss of power and causing the motor to overheat. Use the chart provided below to determine the minimum wire size required in an extension cord. Only round jacketed cords listed by Underwriter’s Laboratories (UL) should be used.

**Ampere rating (on tool faceplate)

 

0-2.0

2.1-3.4

3.5-5.0 5.1-7.0

7.1-12.0

12.1-16.0

Cord Length

Wire Size (A.W.G.)

 

 

 

 

 

 

 

 

 

25'

16

16

16

16

14

14

 

 

 

 

 

 

 

50'

16

16

16

14

14

12

 

 

 

 

 

 

 

100'

16

16

14

12

10

**Used on 12 gauge - 20 amp circuit. NOTE: AWG = American Wire Gauge

When working with the tool outdoors, use an extension cord that is designed for outside use. This is indicated by the let- ters “WA” on the cord’s jacket.

Before using an extension cord, inspect it for loose or exposed wires and cut or worn insulation.

WARNING:

Keep the extension cord clear of the working area. Position the cord so that it will not get caught on lumber, tools or other obstructions while you are working with a power tool. Failure to do so can result in serious personal injury.

WARNING:

Check extension cords before each use. If damaged re- place immediately. Never use tool with a damaged cord since touching the damaged area could cause electrical shock resulting in serious injury.

ELECTRICAL CONNECTION

This tool is powered by a precision built electric motor. It should be connected to a power supply that is 120 volts, 60 Hz, AC only (normal household current). Do not operate this tool on direct current (DC). A substantial voltage drop will cause a loss of power and the motor will overheat. If the tool does not operate when plugged into an outlet, double check the power supply.

SPEED AND WIRING

The no-load speed of this tool is approximately 10,000 rpm. This speed is not constant and decreases under a load or with lower voltage. For voltage, the wiring in a shop is as important as the motor’s horsepower rating. A line in- tended only for lights cannot properly carry a power tool motor. Wire that is heavy enough for a short distance will be too light for a greater distance. A line that can support one power tool may not be able to support two or three tools.

GROUNDING INSTRUCTIONS

In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This tool is equipped with an electric cord having an equipment-grounding conduc- tor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided. If it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-grounding conductor can result in a risk of electric shock. The conductor with insulation having an outer surface that is green with or with- out yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is neces- sary, do not connect the equipment-grounding conductor to a live terminal.

Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.

Repair or replace a damaged or worn cord immediately.

This tool is intended for use on a circuit that has an outlet like the one shown in figure 1. It also has a grounding pin like the one shown.

GROUNDING

PIN COVER OF GROUNDED

OUTLET BOX

Fig. 1

8

Image 8
Contents OPERATOR’S Manual Save this Manual for Future ReferenceWarranty IntroductionGeneral Safety Rules Read ALL InstructionsSpecific Safety Rules Inspect Extension Cords Periodically and replace if damagedSpecific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Authorized Service Center for repair. When servicSpeed and Wiring ElectricalExtension Cords Electrical ConnectionGlossary of Terms Features Product SpecificationsSwitch KEY Power Depth Adjustment Handle Dust Port Work Thickness ScaleLoose Parts Assembly UnpackingWorkbench Installing Depth Adjustment HandleMounting the Planer Operation ApplicationsThickness Planing Planing TipsWarped Wood Power SwitchAvoiding Snipe Adjusting the Planing Depth To Adjust the Planing DepthDepth Adjustment Handle Adjusting Knob Scale PlaningAdjustments Thickness Scale AdjustmentBlade Adjustment Slide Blade LoosenMaintenance General MaintenanceBlade Replacement LubricationBrush Brush CAP Brush ReplacementCleaning Troubleshooting Problem Possible Cause SolutionPage Service Model NO. and Serial no