Stanley Black & Decker SK58 user manual Hose Types, Hose Safety Tags

HOSE TYPES

The rated working pressure of the hydraulic hose must be equal to or higher than the relief valve setting on the hy- draulic system. There are three types of hydraulic hose that meet this requirement and are authorized for use with Stanley Hydraulic Tools. They are:

Certified non-conductive— constructed of thermoplastic or synthetic rubber inner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. Hose labeled certified non- conductive is the only hose authorized for use near electrical conductors.

Wire-braided(conductive) — constructed of synthetic rubber inner tube, single or double wire braid reinforce- ment, and weather resistant synthetic rubber cover. This hose is conductive and must never be used near electrical conductors.

Fabric-braided(not certified or labeled non-conductive) — constructed of thermoplastic or synthetic rubber in- ner tube, synthetic fiber braid reinforcement, and weather resistant thermoplastic or synthetic rubber cover. This hose is not certified non-conductiveand must never be used near electrical conductors.

HOSE SAFETY TAGS

To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS.

If the information on a tag is illegible because of wear or damage, replace the tag immediately. A new tag may be obtained from your Stanley Distributor.

THE TAG SHOWN BELOW IS ATTACHED TO “CERTIFIED NON-CONDUCTIVE” HOSE

A G	D A N G E R		D A N G E R
T
I S	1. FAILURE TO USE HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE	3.	DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE
H	WHEN USING HYDRAULIC TOOLS ON OR NEAR ELECTRIC LINES MAY RESULT IN		OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE.
T	DEATH OR SERIOUS INJURY.		KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT
VE	FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROP-		CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION
			AND SEVERE PERSONAL INJURY.
O	ERLY TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND
	ELECTRIC LINES.	4.	HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, ABRASION, CUTTING, OR
M
			CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT
E
	2. BEFORE USING HYDRAULIC HOSE LABELED AND CERTIFIED AS NON-CONDUCTIVE		USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.
R
	ON OR NEAR ELECTRIC LINES. WIPE THE ENTIRE LENGTH OF THE HOSE AND FIT-	5. CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAM-
T
	TING WITH A CLEAN DRY ABSORBENT CLOTH TO REMOVE DIRT AND MOISTURE AND
			AGE TO COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE
N O	TEST HOSE FOR MAXIMUM ALLOWABLE CURRENT LEAKAGE IN ACCORDANCE WITH
			IMMEDIATELY. NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
	SAFETY DEPARTMENT INSTRUCTIONS.	6.
D O			AFTER EACH USE STORE IN A CLEAN DRY AREA.
	SEE OTHER SIDE		SEE OTHER SIDE
			SIDE 2
	SIDE 1

(Shown smaller than actual size)

THE TAG SHOWN BELOW IS ATTACHED TO “CONDUCTIVE” HOSE.

D O N O T R E M O V E T H I S T A G

D O N O T R E M O V E T H I S T A G

	D A N G E R		D A N G E R
1.	DO NOT USE THIS HYDRAULIC HOSE ON OR NEAR ELECTRIC LINES. THIS HOSE IS	5.	CHECK ENTIRE HOSE FOR CUTS CRACKS LEAKS ABRASIONS, BULGES, OR DAMAGE TO
	NOT LABELED OR CERTIFIED AS NON-CONDUCTIVE. USING THIS HOSE ON OR NEAR		COUPLINGS IF ANY OF THESE CONDITIONS EXIST, REPLACE THE HOSE IMMEDIATELY.
	ELECTRICAL LINES MAY RESULT IN DEATH OR SERIOUS INJURY.		NEVER USE TAPE OR ANY DEVICE TO ATTEMPT TO MEND THE HOSE.
2.	FOR PROPER AND SAFE OPERATION MAKE SURE THAT YOU HAVE BEEN PROPERLY	6.	AFTER EACH USE STORE IN A CLEAN DRY AREA.
	TRAINED IN CORRECT PROCEDURES REQUIRED FOR WORK ON OR AROUND ELEC-
	TRIC LINES.

3.DO NOT EXCEED HOSE WORKING PRESSURE OR ABUSE HOSE. IMPROPER USE OR HANDLING OF HOSE COULD RESULT IN BURST OR OTHER HOSE FAILURE. KEEP HOSE AS FAR AWAY AS POSSIBLE FROM BODY AND DO NOT PERMIT DIRECT CONTACT DURING USE. CONTACT AT THE BURST CAN CAUSE BODILY INJECTION AND SEVERE PERSONAL INJURY.

4.HANDLE AND ROUTE HOSE CAREFULLY TO AVOID KINKING, CUTTING, OR CONTACT WITH HIGH TEMPERATURE SURFACES. DO NOT USE IF KINKED. DO NOT USE HOSE TO PULL OR LIFT TOOLS, POWER UNITS, ETC.

SEE OTHER SIDE		SEE OTHER SIDE
SIDE 1		SIDE 2
	(Shown smaller than actual size)

D O N O T R E M O V E T H I S T A G

SK58 User Manual ◄ 7