Unpacking, Mounting and Assembly, Operation

Unpacking, Mounting and Assembly

1.With the help of an assistant, carefully uncrate the planishing hammer. A tab is welded to the top tube if you choose to use a hoist to set up the machine.

2.Determine the most suitable location for your planishing hammer based on the planned usage of the machine. Larger workpieces require a larger space around the planishing hammer.

3.Mount any loose items to the frame, such as the die trays, using the photo on page 7 and the breakdown on page 10 as guides.

4.Lower the foot pads to contact the floor, using the handwheel.

5.Secure the planishing hammer to the floor using fasteners (not included) appropriate for the floor type. These are inserted through the holes on the frame’s back leg.

Referring to Figure 2:

6.Attach the pneumatic hammer to the frame with the upper clamp (has rounded notch) and lower clamp. Secure the clamps with four M6x25 socket head cap screws and M6 lock washers.

Referring to Figure 3:

7.Check the oil level in the lubricator. If the oil level is low, refill. Refer to Maintenance section for instructions.

8.Install a male 1/4" quick connector fitting onto the air inlet of the planishing hammer.

Operation

Keep hands clear of hammer and anvil area at all times! Failure to comply may cause serious injury!

Referring to Figure 3:

1.Connect the air compressor to the quick connector.

2.Set the desired air pressure between 90-120 PSI using the pressure dial on the filter/regulator (clockwise to increase). Lock the setting by pushing down the pressure dial. Pull up on the dial to readjust a setting. Note: A lower air pressure will provide a softer hammer blow. Do not exceed 120 psi air pressure.

3.Adjust the oil flow using the dial at the top of the lubricator. A setting of 2 drips per minute is sufficient for regular operation.

Figure 3

Referring to Figure 4:

4.Adjust the anvil height with the handwheel, and secure the anvil in position by snugging the lock collar against the frame.

5.The lock handle can be inserted into any of the threaded holes in the collar, and tightened using a wrench on the flats.

Figure 2

PH-24T specifications

The Jet Tools PH-24T is a high-performance planer that stands out in the woodworking industry for its precision and efficiency. This powerful tool is designed for professionals and hobbyists alike, offering a range of features that make it a favorite among woodworkers seeking smooth and accurate finishes on their projects.

One of the main features of the Jet Tools PH-24T is its robust 15-amp motor, which provides consistent power and durability. This motor is capable of driving the cutter head at an impressive speed of 8,000 RPM, allowing the planer to remove up to 1/8 inch of material in a single pass. This capability not only speeds up the milling process but also ensures a clean and smooth surface, reducing the need for additional sanding.

The PH-24T is equipped with a precision-ground cast iron table that is large enough to support larger workpieces, providing stability and reducing the chance of snipe during operation. This table is adjustable, allowing users to fine-tune their setup for precise cuts. The tool also features extra-long infeed and outfeed tables, which help in guiding the wood smoothly through the planer, further enhancing the quality of the finish.

Another standout aspect of the Jet Tools PH-24T is its quick-change cutter head, which allows for easy blade replacement. The blades are high-speed steel and razor-sharp, offering users a long-lasting cutting edge. The design of the cutter head facilitates efficient chip removal, minimizing clogging and ensuring a clean cut.

The integrated dust collection port can connect to a vacuum system, effectively managing chips and debris during operation. This feature not only keeps the workspace clean but also enhances visibility and safety while working.

Safety features are also prioritized in the Jet Tools PH-24T. It comes with safety guards and emergency stop switches, giving users peace of mind while operating the planer.

In summary, the Jet Tools PH-24T is an exceptional planer that blends power, precision, and safety features. Its robust motor, adjustable components, and user-friendly design make it an essential tool for anyone serious about woodworking. Whether you're flattening rough lumber or finishing pieces, the PH-24T delivers outstanding results with every use, making it a valuable addition to any workshop.