DeWalt D25980 instruction manual Components FIG, Assembly and Adjustments, Features FIG, Operation

English

FIG. 1	A	G
		I
	B

D

HC

F

E

COMPONENTS (FIG. 1)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

NOTE: Left and right describes the location of the part with the operator standing behind the pavement breaker with the front of the tool facing away.

A. ON/OFF switch	F. Active vibration control
B. Right side handle	G. Front of tool
C. Left side handle	H. Hex head screws
D. Bit retainer	I. Air vents
E. Bit holder

INTENDED USE

D25980 demolition hammer has been designed for professional heavy duty demolition, chipping and chasing applications in concrete, brick, stone and other masonry materials.

DO NOT use under wet conditions or in presence of flammable liquids or gases.

These demolition hammers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

Side Handle (Fig. 1)

CAUTION: ALWAYS operate the tool with the side handle properly assembled. Hold tool with both hands to maximize control.

Attach left side handle (C) with four hex head screws (H, supplied). Tighten with hex wrench supplied.

FEATURES (FIG. 1)

On/off Switch

The weight of the hand will active/deactivate the on/off switch. Firmly grasp pavement breaker while applying pressure with the right hand to turn the pavement breaker on. To turn the tool off, remove the right hand to relieve pressure from the switch.

Soft Start

Holding tool by both handles depress the on/off switch (A). The Soft Start feature allows the impact rate to build up more slowly preventing the bit or point from bouncing around on the surface. To stop the pavement breaker pull up on hand to relieve pressure from the switch to turn the tool off.

SHOCKS™ – Active Vibration Control

The active vibration control (F) helps absorb the vibration transmitted to the user. This improves user comfort and safety during operation.

Hold the tool firmly with one hand on the left side handle (C) and the other hand on the right side handle (B). Using the right hand apply weight to the on/off switch (A) to turn on. Apply only enough pressure to the work area to engage the active vibration control. Applying too much pressure will not make the pavement breaker chisel faster and the active vibration control will not engage.

OPERATION

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An

accidental start-up can cause injury.

CAUTION: Always hold tool with both hands to maximize control. Allow the hammer to do the work. Excessive added force shortens the life of the hammer and the accessory.

Bits (Fig. 2, 3)

WARNING: To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause injury.

WARNING: ALWAYS wear gloves when you change bits. Accessible metal parts on the tool and bits may get extremely hot during operation.

WARNING: To reduce the risk of injury, only DEWALT recommended accessories should be used with this product. A variety of bits are available from your local retailer.

NOTE: Insert bits with the front of tool (G) facing up.

TO INSERT AIR STEEL BITS (RING-ONLY BIT)

1.Pull bit retainer (D) open as shown in Figure 2A.

2.Insert bit into bit holder (E) and close bit retainer onto bit as shown in Figure 2B.

TO INSERT TOOL STEEL BITS (NOTCH-ONLY BIT)

1.Pull bit retainer (D) open as shown in Figure 3A.

2.Insert bit with notch (J) facing up into bit holder (E).

3.Pull bit retainer up to lock into position as shown in Figure 3B.

Use either of the above methods to insert combination steel (notch and ring bit)

To Operate

NOTE: Use sharp drill bits only.

1.Insert bit as described in Bits.

2.Standing behind the tool with both hands on the handles, depress the on/off switch to start the tool. Hold handles firmly to control tool.

3.Remove hand to relieve pressure from the on/off switch to turn the tool off.

4.Place hands under handles and lift up to move tool.

3