Craftsman 315.114073 manual LED Functions of Charger, Charging the Battery Pack

Page 10

WARNING: Do not allow familiarity with worklights

to make you careless, Remember that a careless fraction of a second is sufficient to inflict serious

injury.

,_ WARNING: Do not use any attachments or acces-

sories not recommended by the manufacturer of this worklight. The use of attachments or accessories not recommended can result in serious personal injury.

CAUTION: If at any point during the charging process none of the LEDs are lit, remove the bat- tery pack from the charger to avoid damaging the product, DO NOT insert another battery. Return the charger and battery to your nearest service center for service or replacement.

LED FUNCTIONS OF CHARGER

LED WILL BE ON TO INDICATE STATUS OF

CHARGER AND BA'rrERY PACK:

•Red LED on = Fast charging mode.

•Green LED on = Fully charged and in maintenance charge mode.

•Green LED on = When battery pack is inserted into charger, indicates hot battery pack or that battery pack is out of normal temperature range.

•Yellow and Green LEDs on = Deeply discharged or defective battery pack.

•No LED on = Defective charger or battery pack.

CHARGING THE BATTERY PACK

The battery pack for this worklight has been shipped in a low charge condition to prevent possible problems. There- fore, you should charge it until the green LED on the front of the charger comes on.

NOTE: Batteries will not reach full charge the first time they are charged. Allow several cycles (operation followed by recharging) for them to become fully charged.

CHARGING A COOL BATTERY PACK

If battery pack is below normal temperature range, the green LED on charger will come on. Allow battery pack to reach normal temperature, then the red LED will come on.

NOTE: If the charger does not charge the battery pack under normal circumstances, return both the battery pack and charger to your nearest Sears Repair Center for electrical check.

•Charge the battery pack only with the charger provided.

•Make sure the power supply is normal household voltage, 120 volts, 60 Hz, AC only,

•Connect the charger to the power supply.

•Place the battery pack in the charger aligning raised rib on the battery pack with the groove in the charger. See Figure 2.

•Press down on the battery pack to be sure contacts on the battery pack engage properly with contacts in the charger.

•Normally the red LED on charger will come on. This indicates the charger is in fast charging mode.

•Red LED should remain on for approximately t hour then the green LED will come on. Green LED on indicates battery pack is fully charged and charger is in maintenance charge mode.

NOTE: The green LED will remain on until the battery pack is removed from the charger or charger is disconnected from the power supply.

•If both yellow and green LEDscome on, this indicates a deeply discharged or defective battery pack. Allow the battery pack to remain in the charger for 15 to 30 minutes. When the battery pack reaches normal voltage range, the red LED should come on. If the red LED does not come on after 30 minutes, this may indicate a defective battery pack and should be replaced.

•After normal usage, a minimum of 1 hour of charging time is required to fully recharge battery pack.

•The battery pack will become slightly warm to the touch while charging. This is normal and does not indicate a problem.

•Do not place the charger and battery pack in an area of extreme heat or cold. They will work best at normal room temperature.

NOTE: The charger and battery pack should be placed in a location where the temperature is more than 5O°F but less than 100°F.

•When batteries become fully charged, unplug the charger from power supply and remove the battery pack.

BATrERYPACK

SHOWNIN CHARGER

CHARGER

REOLEO

GREEN

LED

LED

Fig. 2

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Icrrftsmrni Save this manual for future referenceONE Year Full Warranty on Craftsman Tool Sears, Roebuck and Co., Dept WA, Hoffman Estates, IIRead ALL Instructions Model Battery Pack ChargerService Worklight USE and CareSafety Rules for Battery Worklights Page Symbol Name DESIGNATION/EXPLANATION Symbol Signal Meaning Your nearest Authorized Service Center forHanging Product SpecificationsSwitch Trigger Know Your Worklight HANGING/STORAGE HookUnpacking Packing ListVolt FluorescentLight LED Functions of Charger Charging the Battery PackCharging a Cool Battery Pack LED will be on to Indicate StatusLatches Charging a HOT Battery PackTo INSTALL/REMOVE Battery Pack To RemoveTo turn the Jighton and off, depress the switch trigger General MaintenanceSwitch Trigger SwitchPulllenscover Forwardtorubber Fluorescent Tube ReplacementTo Replace Fluorescent Tube Screw Lenscover Fluorescenttube BulbsocketBattery Pack Removal Preparation for Recycling BatteriesGet it fixed, at your home or ours

11407, 315.114073 specifications

The Craftsman 315.114073, also known as the 11407 model, is a versatile and reliable power tool that has garnered appreciation among DIY enthusiasts and professional users alike. This model is primarily designed for users seeking efficiency and performance in their woodworking and crafting tasks.

One of the standout features of the Craftsman 315.114073 is its robust motor. The tool is powered by a durable electric motor that delivers a consistent performance, enabling it to handle a variety of materials with ease. With a torque output that effectively manages heavy-duty tasks, users can expect smooth operation whether they are working with wood, plastic, or light metals.

The design of the Craftsman 315.114073 emphasizes user comfort and control. It is equipped with an ergonomic handle that reduces fatigue during prolonged use, allowing for greater precision and accuracy in various projects. The tool's lightweight construction further enhances maneuverability, making it an ideal choice for intricate tasks and extended work sessions.

The model also features adjustable speed settings, granting users the flexibility to tailor their approach to different materials and applications. This feature is particularly useful for projects that require both fine and aggressive cutting, allowing users to easily switch between settings for optimal results.

Another highlight of the Craftsman 315.114073 is its comprehensive safety features. The tool is designed with user safety in mind, incorporating protective guards and a safety switch to prevent accidental starts. These safety measures ensure that users can work confidently without the constant worry of mishaps.

In terms of maintenance, the Craftsman 315.114073 stands out for its user-friendly design. It includes easily accessible parts for quick cleaning and maintenance, ensuring longevity and optimal performance. This model also often comes with a range of accessories that enhance its functionality, making it a well-rounded tool for users with various needs.

Overall, the Craftsman 315.114073 is a powerful, ergonomic, and user-friendly tool that meets the demands of both amateur and seasoned craftsmen. Its combination of features, technologies, and safety characteristics makes it a commendable choice for anyone looking to invest in a reliable power tool for their crafting projects.
Top Page Image Contents