Agilent Technologies 8166A, 8163A, 8164A SENSenCHANnelmFUNCtionPARameterSTABility, Period time

Page 96

Measurement Operations & Settings

Measurement Functions – The SENSe Subsystem

example:

affects:

dual sensors:

sens1:func:par:minm? WIND,+10<END> All power meters and return loss modules

Can only be sent to master channel, slave channel parameters are identical.

Setting parameters for the stability function sets some parameters,

N O T E including hidden parameters, for the logging and MinMax functions and vice versa. You must use the :SENSe[n][:CHANnel[m]]:FUNCtion:PARameter:STABility command to set parameters before you start a stability function using the :SENSe[n][:CHANnel[m]]:FUNCtion:STATe command.

command:

syntax:

description:

parameters:

:SENSe[n][:CHANnel[m]]:FUNCtion:PARameter:STABility

:SENSe[n][:CHANnel[m]]:FUNCtion:PARameter:STABility<wsp>

<total time>[NSUSMSS],<period time>[NSUSMSS],<averaging time>[NSUSMSS]

Sets the total time, period time, and averaging time for the stability data acquisition function.

Total time:

The total time from the start of stability mode until it is completed.

Period time:

A new measurement is started after the completion of every period time.

Averaging time:

A measurement is averaged over the averaging time.

Measurement Running

Measurement Stopped

1

Averaging Time

Period Time

2

 

3

 

 

 

4

5

t

N O T E

N O T E

N O T E

N O T E

response:

example:

affects:

dual sensors:

The total time should be longer than the period time.

The period time should be longer than the averaging time.

The number of data points is equal to the total time divided by the period time. Total time, period time, and averaging time are time values in seconds.

If you specify no units in your command, seconds are used as the default.

See “:SENSe[n][:CHANnel[m]]:FUNCtion:STATe” on page 100 for information on starting/stop- ping a data acquisition function.

See “:SENSe[n][:CHANnel[m]]:FUNCtion:RESult?” on page 97 for information on accessing the results of a data acquisition function.

See “Triggering and Power Measurements” on page 171 for information on how triggering af- fects data acquisition functions.

none

sens1:func:par:stab 1s,0.1s,0.1s

All power meters and return loss modules

Can only be sent to master channel, slave channel is also affected.

96

Agilent 8163A/B, 8164A/B & 8166A/B Mainframes, Fifth Edition

Image 96
Contents Agilent Technologies Warn in G WA R N I N G Agilent Technologies Sales and Service Offices Japan 0120 421 0120 421 678 FAX Mexico 5081Structure of this Manual Conventions used in this ManualThis manual is divided into 5 parts Related Manuals T ETable of Contents Specific Command Summary Root Layer CommandSignal Generation The SOURce Subsystem Signal ConditioningInstalling the Agilent 816x Instrument Driver Using Visual Programming EnvironmentsFeatures of the Agilent 816x Instrument Driver Error HandlingCompatibility Issues Preset DefaultsRemoved Command Obsolete CommandsOperational/Questionable Status System for Agilent 8163A/B, 8164A/B & 8166A/B Mainframes, Sixth EditionAgilent 8163A/B, 8164A/B & 8166A/B Mainframes, Sixth Edition List of Tables Agilent 8163A/B, 8164A/B & 8166A/B Mainframes, Sixth Edition Introduction to Programming Gpib Interface Camino del Rio South, Suite 340 San Diego, CAIntroduction to Programming Scpi Consortium Office Bode EnterpriseMnemonic Function If the instrument is in remote control, a screen resembling Returning the Instrument to Local ControlGpib Interface Message Queues Message QueuesHow the Input Queue Works Clearing the Input QueueOutput Queue Error Queue If no error has occurred, the error queue containsIf more than 29 errors are put into the queue, the message Is placed as the last message in the queueCommand message is ended by a line feed character LF or Programming and Syntax Diagram ConventionsCrlf Statusoperationenable Short Form and Long FormIs in long form Short form of this message is StatoperenabCommand and Query Syntax Unit Default Allowed MnemonicsUnits String Value WspData Types Slot and Channel NumbersLaser Selection Numbers Input to your Return Loss module for the following commands 112,Common Commands Common CommandsCommon Command Summary Gives a summary of the common commandsParameter Function ESE sets the Standard Event Status Enable Mask All bits shown as are unused Event Status Enable MaskCommon Status Information T E Status Model Status RegistersStatus Model Status System for 8163A/B & 8164A/B Slot Status EventSlot Status Condition Status System for 8166A/B Annotations Status Byte RegisterStandard Event Status Register Operation/Questionable Status SummaryOperation/Questionable Status Summary Register Operation/Questionable Slot StatusOperation Slot Status Register Questionable Slot Status RegisterStatus Model Status Command Summary LongOther Commands OPT? WAI IDN?Introduction to Programming Specific Commands Specific Command Summary Specific CommandsCommand Description WAVelengthREFerence/?Command Description DISPlay FETChnCHANnelmSCALarINITiatenCHANnelm INPUTnCHANnelmPATH/? TerminalsREADnCHANnelm ROUTenSENSenCHANnelmPOWer SENSenCHANnelmFUNCtionCommand Description SENSenCHANnelmPOWerReference SENSenCHANnelmRETurnlossCALibrationSENSenCHANnelmRETurnlossCORRection SLOTnSOURcenCHANnelmPOWer SOURcenCHANnelmPOWerATTenuationlSOURcenCHANnelm SOURcenCHANnelmAMSOURcenCHANnelmWAVelengthCORRection SOURcenCHANnelmWAVelengthREFerenceCommand Description SOURcenCHANnelmWAVelengthSWEep SOURcenCHANnelmWAVelengthSWEepSTEPCommand Description SPECial STATusnSTATusOPERation STATusnOPERationCommand Description STATusnQUEStionable Slot nSYSTem SYSTemCOMMunicateGPIBSpecific Commands Instrument Setup and Status IEEE-Common Commands Instrument Setup and StatusError queue At power-on By sending a value of zeroStandard event status register Sesr Status byte register STBESE? Bit Mnemonic Decimal ValueComplete, Command Idle State Power-onParameters None Response Identification terminated by END Agilent Technologies ManufacturerPlete, Command Idle State Lead to useful gains in program execution efficiencySlot 1 for the Agilent 8163A/B and Agilent 8166A/B Example OPT? → 81682A , , 81533B, 81532A, ENDError queue Following are not changedBits Mnemonic Selftest failed on MainframeWAI Pending operations, are completed during the wait periodStatus Reporting The STATus Subsystem STATusOPERationEVENtLEVel0?Bits Mnemonics Agilent 8163A/B Agilent 8164A/B Agilent 8166A/BStatus Reporting The STATus Subsystem STATusOPERationCONDitionLEVel0?STATusOPERationENABleLEVel STATusOPERationENABleLEVel0?STATusOPERationEVENtLEVel1? Bits Mnemonics Decimal Value Agilent 8166A/BSTATusOPERationENABleLEVel1 Syntax STATusOPERationENABleLEVel1wspvalue DescriptionSTATusOPERationENABleLEVel1? STATusOPERationCONDitionLEVel1?Offset Extrapolated valuesSTATus nOPERationEVENt? STATus nOPERationCONDition?STATusnOPERationENABle STATusnOPERationENABlewspvalueSTATusnOPERationENABle? STATusPRESetSTATusQUEStionableEVENtLEVel0? Agilent 8163A/B Agilent 8164A/BStatques? → +0END STATusQUEStionableCONDitionLEVel0? STATusQUEStionableENABleLEVel STATusQUEStionableENABleLEVel0?STATusQUEStionableEVENtLEVel1? Syntax STATusQUEStionableENABleLEVel 1wspvalue Description STATusQUEStionableENABleLEVel1?STATusQUEStionableCONDitionLEVel 1? Syntax STATusQUEStionableCONDitionLEVel 1? DescriptionSTATusnQUEStionableEVENt? Syntax STATusnQUEStionableEVENt? Description11-15 Not Used STATusnQUEStionableCONDition?STATusnQUEStionableENABle STATusnQUEStionableENABlewspvalueSTATusnQUEStionableENABle? SYSTemERRor? SYSTemDATESYSTemDATE? Output and error queues Standard Event Status Enable Mask SESEM,Gpib interface state Backlight and contrast of the displaySYSTemTIME? SYSTemVERSion?SYSTemCOMMunicateGPIBSELFADDRess SystcommgpibaddrMeasurement Operations & Settings Root Layer Command Measurement Operations & SettingsLOCK? Agilent Technologies as the manufacturer ManufacturerSlot nEMPTy? Slot nIDN?SLOTnTST? SLOTnHEADnEMPTy?SLOTnHEADnIDN? SLOTnHEADmOPTions? SLOTnHEADmTST?SLOTnHEADmWAVelengthRESPonse? Syntax SLOTnHEADmWAVelengthRESPonse? DescriptionSPECialREBoot SLOTnHEADmWAVelengthRESPonseCSV?SLOTnHEADmWAVelengthRESPonseSIZE? Command Measurement Functions SENSe SubsystemAgilent 81635A and Agilent 81619A Master Slave Channels Measurement Functions The SENSe SubsystemSENSenCHANnelmPOWerUNIT/? SENSenCHANnelmPOWerWAVelength/? FETChnCHANnelmSCAlarPOWerDC? FETChnCHANnelmSCAlarRETurnloss?FETChnCHANnelmSCAlarMONitor? INITiatenCHANnelmIMMediateINITiatenCHANnelmCONTinuous Read nCHANnel mSCALarPOWerALL? INITiate nCHANnel mCONTinuous?Read nCHANnel mPOWerALLCONFig? READnCHANnelmSCALarPOWerDC?Ber Member of the pair represents the channel numberREADnCHANnelmSCALarMONitor? READnCHANnelmSCALarRETurnloss?SENSe nCHANnel mCORRectionLOSSINPutMAGNitude SENSenCHANnelmCORRectionLOSSINPutMAGNitude?SENSenCHANnelmCORRectionCOLLectZERO SENSe nCHANnel mCORRectionCOLLectZERO? OperationSENSenCHANnelmCORRectionCOLLectZEROALL SENSenCHANnelmFUNCtionPARameterLOGGing Averaging TimeSENSenCHANnelmFUNCtionPARameterLOGGing? SENSenCHANnelmFUNCtionPARameterMINMax SENSenCHANnelmFUNCtionPARameterMINMax?Cont WindSENSenCHANnelmFUNCtionPARameterSTABility Period timeAveraging Time Period Time Response Example Affects Dual sensorsSENSenCHANnelmFUNCtionPARameterSTABility? SENSenCHANnelmFUNCtionRESult?Sens1funcres? → Return Loss modulesSENSe nCHANnel mFUNCtionRESultBLOCk? SENSe nCHANnel mFUNCtionRESultMAXBlocksize?SENSenCHANnelmFUNCtionRESultMONitor? 100 SENSenCHANnelmFUNCtionSTATeSENSenCHANnelmFUNCtionSTATe? SENSenCHANnelmPOWerATIMe 101SENSenCHANnelmFUNCtionTHReshold SENSenCHANnelmFUNCtionTHReshold?SENSenCHANnelmPOWerATIMe? SENSenCHANnelmPOWerRANGeUPPerRange Upper Linear Power Limit 102SENSenCHANnelmPOWerRANGeUPPer? SENSenCHANnelmPOWerRANGeMONitorUPPer103 Range Upper LinearSENSenCHANnelmPOWerRANGeMONitorUPPer? SENSenCHANnelmPOWerRANGeAUTOMent. Otherwise, it must be set by the sensnpowrang command SENSenCHANnelmPOWerRANGeAUTO?Reference mode using the command 105You must append a unit type DB if you use TOMODule orSENSenCHANnelmPOWerREFerenceDISPlay SENSenCHANnelmPOWerREFerenceSTATeSENSenCHANnelmPOWerREFerenceSTATe? 106SENSe nCHANnel mPOWerREFerenceSTATeRATio SENSenCHANnelmPOWerREFerenceSTATeRATio?107 To the channel for the second valueSENSe nCHANnel mPOWerUNIT SENSenCHANnelmPOWerUNIT?SENSenCHANnelmPOWerWAVelength 108SENSenCHANnelmPOWerWAVelength? 109SENSenCHANnelmRETurnlossCALibrationFACTory SENSenCHANnelmRETurnlossCALibrationFACTory110 SENSe nCHANnel mRETurnlossCALibrationCOLLectTERMinationDefined termination reference measurement. See SENSe nCHANnel mRETurnlossCALibrationTERMination?111 SENSenCHANnelmRETurnlossCORRectionFPDeltalSENSenCHANnelmRETurnlossCORRectionFPDeltal? 112 SENSe nCHANnel mRETurnlossCORRectionREFLectance lDB reference Lower wavelength source is denoted bySignal Generation The SOURce Subsystem 113OUTPutnCHANnelmCONNection OUTPutnCHANnelmCONNection?114 OUTPutnCHANnelmPATH?OUTPutnCHANnelmSTATe 115 SOURcenCHANnelmAMINTernalFREQuencylSOURcenCHANnelmAMINTernalFREQuencyl? 116 SOURcenCHANnelmAMSOURcelSyntax SOURcenCHANnelmAMSOURcelwsp INTINT1INT2COHCAEXTEXTDEXTWVLLBACK012356117 SOURcenCHANnelmAMSTATelSOURcenCHANnelmAMSTATel? Wavelength source is denoted by118 SOURce nCHANnel mAMCOHCtrlCOHLevel lSOURcenCHANnelmAMCOHCtrlCOHLevell? SOURcenCHANnelmFMSOURcel119 SOURce nCHANnel mFMSOURce l?SOURcenCHANnelmFMSTATel SOURcenCHANnelmFMSTATel?120 SOURcenCHANnelmFMSBSCtrlFREQuencylMhzkhzhzminmaxdef SOURcenCHANnelmFMSBSCtrlFREQuencyl?121 SOURcenCHANnelmFMSBSCtrlLevell?SOURcenCHANnelmMODout SOURcenCHANnelmMODout?SOURcenCHANnelmPOWerATTenuationl? 122SOURcenCHANnelmPOWerATTenuationlAUTO SOURcenCHANnelmPOWerATTenuationlAUTO?SOURcenCHANnelmPOWerATTenuationlDARK This command is available in Attenuation Mode OnlySOURcenCHANnelmPOWerATTenuationlDARK? SOURcenCHANnelmPOWerLEVelIMMediateAMPLitudel124 SOURcenCHANnelmPOWerLEVelIMMediateAMPLitudel? 125Also allowed MIN minimum amplitude level SOURcenCHANnelmPOWerLEVelRISetimel SOURcenCHANnelmPOWerLEVelRISetimel?126 SOURce nCHANnel mPOWerSTATe SOURcenCHANnelmPOWerSTATe?SOURcenCHANnelmPOWerUNIT SOURcenCHANnelmPOWerUNIT?SOURcenCHANnelmPOWerWAVelength SOURcenCHANnelmPOWerWAVelength?128 129 SOURce nCHANnel mREADoutDATA?Pmax SOURce nCHANnel mREADoutDATABLOCk?130 SOURcenCHANnelmWAVelengthCWlFIXEDlwspvalueSOURcenCHANnelmREADoutPOINts? SOURcenCHANnelmWAVelengthCWlFIXEDl131 SOURcenCHANnelmWAVelengthCWlFIXEDl?SOURcenCHANnelmWAVelengthCORRectionARA 132 SOURce nCHANnel mWAVelengthCORRectionARAALLSOURce nCHANnel mWAVelengthCORRectionAUTocalib 81989A, 81949A133 SOURce nCHANnel mWAVelengthCORRectionZEROSOURcenCHANnelmWAVelengthCORRectionZEROALL 134 SOURcenCHANnelmWAVelengthCORRectionZEROAUTOSOURcenCHANnelmWAVelengthFREQuencyl Thzghzmhzkhzhz135 SOURcenCHANnelmWAVelengthFREQuencyl?SOURcenCHANnelmWAVelengthREFerencel? SOURcenCHANnelmWAVelengthREFerenceDISPlay136 SOURcenCHANnelmWAVelengthSWEepCHECkparams?Message 137 ValueMINMAXDEF0SOURce nCHANnel mWAVelengthSWEepCYCLes SOURce nCHANnel mWAVelengthSWEepCYCLes?138 SOURce nCHANnel mWAVelengthSWEepDWELlSOURce nCHANnel mWAVelengthSWEepDWELl? SOURcenCHANnelmWAVelengthSWEepEXPectedtriggers?139 SOURcenCHANnelmWAVelengthSWEepFLAG?Sweep state Start Sweep waiting for trigger Trigger →Following settings are the prerequisites for Lambda Logging 140SOURcenCHANnelmWAVelengthSWEepLLOGging SOURcenCHANnelmWAVelengthSWEepLLOGgingwspOFFON01141 SOURcenCHANnelmWAVelengthSWEepMODESOURcenCHANnelmWAVelengthSWEepMODE? SOURcenCHANnelmWAVelengthSWEepPMAX?142 SOURcenCHANnelmWAVelengthSWEepREPeatSOURcenCHANnelmWAVelengthSWEepREPeat? 143 SOURce nCHANnel mWAVelengthSWEepSOFTtriggerSOURcenCHANnelmWAVelengthSWEepSPEed SOURcenCHANnelmWAVelengthSWEepSPEed?144 SOURce nCHANnel mWAVelengthSWEepSTARtSOURcenCHANnelmWAVelengthSWEepSTARt? SOURcenCHANnelmWAVelengthSWEepSTOPIf you enable lambda logging see 145SOURcenCHANnelmWAVelengthSWEepSTOP? SOURcenCHANnelmWAVelengthSWEepSTATe146 SOURcenCHANnelmWAVelengthSWEepSTATe?SOURcenCHANnelmWAVelengthSWEepSTEPNEXT SOURcenCHANnelmWAVelengthSWEepSTEPPREVious147 SOURce nCHANnel mWAVelengthSWEepSTEPWIDTh?Signal Conditioning INPut and OUTput commands148 INPut nCHANnel mATTenuation149 INPutnCHANnelmOFFSetINPutnCHANnelmOFFSet? INPutnCHANnelmOFFSetDISPlayINPutnCHANnelmOFFSetPOWermeter 150INPutnCHANnelmATTenuationSPEed INPutnCHANnelmATTenuationSPEed?151 INPutnCHANnelmWAVelengthMAX DEF INPutnCHANnelmWAVelength?OUTPutnCHANnelmPOWer OUTPutnCHANnelmPOWer?152 OUTPut nCHANnel mAPMode?OUTPutnCHANnelmPOWerREFerence OUTPutnCHANnelmPOWerREFerence?OUTPutnCHANnelmPOWerREFerencePOWermeter 153OUTPutnCHANnelmPOWerOFFSet OUTPutnCHANnelmPOWerOFFSet?OUTPutnCHANnelmPOWerOFFSetPOWermeter 154OUTPut nCHANnel mPOWerCONTRol OUTPutnCHANnelmPOWerCONTRol?OUTPutnCHANnelmPOWerUNit 155OUTPut nCHANnel mPOWerUNit? OUTPutnCHANnelmSTATeAPOWeron156 OUTPut nCHANnel mSTATeOUTPutnCHANnelmSTATeAPOWeron? 157OUTPutnCHANnelmATIMe OUTPutnCHANnelmATIMe?158 OUTPutnCHANnelmCORRectionCOLLectionZEROALLOUTPCORRCOLLZER0? → 0END Table of wavelength-dependent offsets 159CONFigurenCHANnelmOFFSetWAVelengthSTATe CONFigurenCHANnelmOFFSetWAVelengthSTATe?160 CONF1OFFSWAVSTAT onCONFigurenCHANnelmOFFSetWAVelengthVALue CONFigurenCHANnelmOFFSetWAVelengthREFerence161 CONF1OFFSWAVREF 4,2CONFigurenCHANnelmOFFSetWAVelengthREFerence? CONFigurenCHANnelmOFFSetWAVelengthVALueWAVelength?CONFigurenCHANnelmOFFSetWAVelengthVALueOFFSet? 162CONFigurenCHANnelmOFFSetWAVelengthVALuePAIR? CONFigurenCHANnelmOFFSetWAVelengthVALueDELeteCONFigurenCHANnelmOFFSetWAVelengthVALueDELeteALL 163CONFigurenCHANnelmOFFSetWAVelengthTABle? CONFigurenCHANnelmOFFSetWAVelengthTABleSIZE?164 CONF1OFFSWAVTABSIZE? →When the attenuator is hosted in Slot TIP Query the Scpi error queue using SYSTERR?Slot Numbers 165Command Semantic 166Display and System Commands Ieee Commands167 Status Commands User Calibration Data168 Signal Routing Switch modules169 ROUTe nCHANnel mROUTenCHANnelmCONFig? Syntax ROUTenCHANnelmCONFig? DescriptionROUTenCHANnelmCONFigROUTe? 170Triggering The TRIGger Subsystem 171Hardware Software Triggering Data Acquisition Functions SensfuncstatGenerating Output Triggers from Power Measurements DISabled An output trigger will never be generated AVGover172 Software Triggering Data Acquisition Functions173 174 TRIGgernCHANnelmINPut?TRIGgernCHANnelmINPutREARm 175 TRIGger nCHANnel mINPutREARm?TRIGgernCHANnelmOFFSet TRIGgernCHANnelmOFFSet value176 TRIGger nCHANnel mOUTPutReturn loss modules Continuous mode, wavswestepwidt is used for triggering, seeOutput triggers using power measurements TRIGgerCONFiguration177 TRIGger nCHANnel mOUTPutREARmTRIGgerCONFiguration? TRIGgerCONFigurationFPEDalTRIGgerCONFigurationFPEDal? 178Extended Trigger Configuration 179TRIGger Bit unsigned integer , see belowExtended Trigger Configuration 180Node a Input Configuration Node B Input Configuration181 Extended Trigger Configuration Example Output Trigger Connector or Individual module slotsOutput Matrix Configuration 182183 Trigconfext #H2,#H0,#H0 is described by -1 and sets one bitSequence starts again at and continues until the sweep ends 184 Mass Storage, Display, and Print Functions 185Display Operations DISPlay Subsystem186 DisplayDISPlayENABle DISPlayENABle?187 DISPlayBRIGhtness?188 Mass Storage, Display, and Print FunctionsDISPlayLOCKout? Instrument using Visa library calls 189Same program CD-ROM 08164-90BC4How to Use Visa Calls 190Visa Programming Examples How to Use Visa Calls 191How to Set up a Fixed Laser Source 192How to Set up a Fixed Laser Source 193194 How to Measure Power using FETCh and Read How to Measure Power using FETCh and Read195 196 197 198 How to Co-ordinate Two Modules How to Co-ordinate Two Modules199 200 201 202 How Power Varies with Wavelength How Power Varies with Wavelength203 204 205 206 How to Log Results How to Log Results207 208 209 210 211 212 Agilent 816x VXIplug&play Instrument Driver 213214 Agilent 816x VXIplug&play Instrument DriverInstalling the Agilent 816x Instrument Driver 215216 217 Program Folder Item OptionsUsing Visual Programming Environments Getting Started with Agilent VEEGpib Interfacing in Agilent VEE 218Using Visual Programming Environments 219Enter the following information Name enter hp816X Select hp816X from the Plug&play Driver Name drop-down list220 Getting Started with LabView 221This folder contains a subfolder named instr.lib 222 FP Conversion Options Box223 LabView is a trademark of National Instruments CorporationInstrument Driver with LabView Getting Started with LabWindows 224Features of the Agilent Instrument Driver Features of the Agilent 816x Instrument Driver225 Directory Structure 226Opening an Instrument Session 227Successful completion of this function returns Visuccess Opening an Instrument SessionClosing an Instrument Session 228229 Visa Data Types and Selected Constant DefinitionsError Handling Check for an error or event after each function230 ViStatus errStatusError Handling 231Introduction to Programming Example ProgramsVISA-Specific Information Development EnvironmentsMicrosoft Visual Basic 4.0 or higher Agilent VEE 5.01 or higherLabWindows CVI/ R 4.0 or higher 233Online Information 234Latest copy of this driver can be downloaded via Lambda Scan Applications 235Lambda Scan Applications Equally Spaced Datapoints 236How to Perform a Lambda Scan Application Prepare Lambda Scan Function237 Get Lambda Scan Parameters Function Execute Lambda Scan Function238 Get Lambda Scan ParametersHow to Perform a Multi-Frame Lambda Scan Application 8164A or B PowerPower 8163A or B 239Equally Spaced Datapoints Function Register Mainframe FunctionUnregister Mainframe Function 240Prepare Multi Frame Lambda Scan Function 241Get MF Lambda Scan Parameters Function Execute Multi Frame Lambda Scan FunctionGet Lambda Scan Result Function 242Get Number of PWM Channels Function Get Channel Location Function243 Maximum number of channels that may be specified is244 Error Codes 257Gpib Error Strings 258259 Program mnemonic too longSuffix too long 260 261 New 185Standard 200 New 201262 Old 211Old 212 Old 213263 Old 221Standard 222 264 265 266 267 To -499 Query Errors 268269 Standard 420Standard 430 Standard 440270 Overview for Unsupported StringsGpib Command Compatibility List 245Compatibility Issues These commands are incompatibleCommand Change Affects Gpib Bus Compatibility247 Preset Defaults Preset defaults are different248 Removed Command 249Obsolete Commands Old Command New Command Affects250 Changed Parameter Syntax Semantics 251SOURAMFREQ/? DispbrigChanged Query Result Values 252TST SENSPOWUNIT?Timing Behavior 253Details the ways in which timing behavior is different Change Affects254 Returned Value AffectsFLT/DBLMAX Command Order Command Order255 Instrument Status Settings 256Index 271272 SlotPage  Agilent Technologies, Deutschland GmbH 08164-90B64
Related manuals
Manual 8 pages 14.45 Kb Manual 16 pages 47.65 Kb

8163A, 8164A, 8166A, B specifications

Agilent Technologies B,86100A is a high-performance oscilloscope and signal integrity analyzer designed primarily for advanced digital communications applications. As a versatile tool, it supports a wide range of testing needs, making it indispensable for engineers and researchers involved in the development and testing of high-speed digital signals.

One of the standout features of the B,86100A is its capability to analyze signals with various bandwidths, accommodating both current and emerging communication standards. The device features a sampling rate of up to 80 GS/s and bandwidth capabilities of 33 GHz to ensure high accuracy in capturing fast signal transitions, which is critical for ensuring the integrity of complex digital signals.

The B,86100A employs Agilent's proprietary digital signal processing (DSP) technology, which significantly enhances measurement precision and reduces noise, enabling users to obtain clearer insights into signal behavior. Its advanced triggering capabilities allow for precise signal capture, making it particularly useful in troubleshooting and validating high-speed designs, as well as in evaluating the performance of optical and electrical devices.

In addition to its high-speed capabilities, the B,86100A offers a robust set of measurement tools including jitter analysis, eye diagram analysis, and equalization assessment. These features allow engineers to effectively analyze signal quality and address potential issues related to signaling distortions and inter-symbol interference.

The graphical user interface of the B,86100A is intuitive, enabling users to efficiently navigate through measurement options and visualize data results. Customizable measurement setups streamline workflow, ensuring that users can quickly adapt their tests to evolving project requirements.

Another key characteristic of the B,86100A is its modularity. The system supports a variety of plug-in modules, which can be tailored to specific application needs, such as different types of optical and electrical signals. This flexibility not only extends the operational capability of the instrument but also makes it a future-proof investment as technology continues to evolve.

In summary, Agilent Technologies B,86100A combines high-speed acquisition with advanced processing capabilities, making it an essential instrument for anyone involved in high-speed digital design and testing. With its ability to deliver precise measurements and extensive analysis features, it empowers engineers to achieve optimal performance and reliability in their systems.