Grizzly T23091 owner manual Service, Troubleshooting

Page 13

SECTION 6: SERVICE

Troubleshooting

IMPORTANT: Air tool repairs must be completed by a qualified service person.

Symptom

Possible Cause

 

Solution

 

 

 

 

 

 

 

Tool runs at

1.

Grinder is being overloaded.

1.

Reduce feed pressure; install a

normal speed but

 

 

 

 

 

 

new or a smaller diameter bit.

bogs down when

2.

Tool adjustment at fault.

 

2.

Re-adjust the throttle valve

grinding, or tool

 

 

 

 

 

 

screw to the fully open

runs slowly with

 

 

 

 

 

 

position.

 

 

little air exiting the

3.

Trigger or lock is bent and

3.

Bend the trigger lock

or trigger

exhaust.

 

binding the trigger.

 

 

back into position so the trigger

 

 

 

 

 

 

 

fully depresses

the

throttle

 

 

 

 

 

 

 

valve.

 

 

 

4.

Intake filter

screen

is

4.

Clean the filter screen behind

 

 

clogged.

 

 

 

 

the air supply fitting (see Figure

 

 

 

 

 

 

 

1, on Page 5).

 

 

 

5.

Insufficient air supply volume

5.

Set the regulator to 90 PSI, or

 

 

or pressure.

 

 

 

 

100 PSI if the air hose is longer

 

 

 

 

 

 

 

than 25 feet. Repair any leaking

 

 

 

 

 

 

 

fittings, remove

all restrictions

 

 

 

 

 

 

 

and hose kinks. Ensure that all

 

 

 

 

 

 

 

hoses and lines have an inside

 

 

 

 

 

 

 

diameter of at least 3⁄8".

 

6.

Tool shank

or

collet insert

6.

Replace worn items. If cutting

 

 

is worn, causing tool to slip

 

wheel is used, verify mounting

 

 

inside collet.

 

 

 

 

arbor is tight.

 

 

 

7.

Incorrect

lubrication

is

7.

Make sure tool is lubricated

 

 

affecting tool.

 

 

 

correctly and does not run

 

 

 

 

 

 

 

dry. Prevent oil from flooding

 

 

 

 

 

 

 

the air tool by re-adjusting the

 

 

 

 

 

 

 

automatic oiler.

 

 

 

8.

Water is entering tool.

 

8.

Service or reposition the air

 

 

 

 

 

 

 

filter water separator as far as

 

 

 

 

 

 

 

possible from the compressor.

 

 

 

 

 

 

 

This allows for maximum air

 

 

 

 

 

 

 

cooling and water condensation

 

 

 

 

 

 

 

for the water separator.

 

9.

Air tool motor clogged with an

9.

Clean or rebuild the air tool as

 

 

oil-water sludge.

 

 

 

required, and correct moisture

 

 

 

 

 

 

 

or lubrication problem in the air

 

 

 

 

 

 

 

supply system.

 

 

 

 

 

 

 

 

 

 

 

 

Model T23091 1⁄4" Air Die Grinder

-11-

Page 12 Page 14
Image 13
Page 12 Page 14
Contents ⁄4 AIR DIE Grinder Page Table of Contents Safety Instructions for Pneumatic Tools SafetyBefore Operating This Equipment Mation about proper operation of the equipmentAdditional Safety Instructions for Pneumatic Die Grinders Introduction SpecificationsForeword Contact Info Identification Collet Insert Throttle Valve Adjustment Screw Collet NutUnpackingAssembly SetupAir supply setup tips InventoryOperation Overview OperationsTo complete a typical cutting or grinding operation G8210-50-Pc. Stone Set AccessoriesT20887 T20881 G6261 G7870 G7872 G7871 G7866 T21767G7867 H3105-Clamp Style Magnifying LampBefore and after each use MaintenancePeriodically as required Troubleshooting ServicePort Model T23091 1⁄4 Air Die Grinder Parts Main Parts Diagram Main Parts ListWarranty

T23091 specifications

The Grizzly T23091 is a powerful and versatile woodworking tool designed to meet the demands of both hobbyists and professional craftsmen. This 10-inch table saw is engineered with precision and innovation, making it an essential addition to any workshop.

One of the standout features of the Grizzly T23091 is its robust 2-horsepower motor. This strong motor allows users to cut through a wide variety of materials, including hardwoods and engineered woods, with ease and accuracy. The saw's direct-drive system ensures efficient power transfer, minimizing energy loss while maximizing cutting performance.

The T23091 boasts a heavy-duty cast iron table, which provides stability and a large work surface for handling sizable workpieces. With its finely ground surface, the table reduces friction, allowing for smoother cuts and enhanced overall performance. Additionally, the table features an extension wing that increases the surface area, making it easier to handle larger sheets of material.

Precision is crucial in woodworking, and the Grizzly T23091 does not disappoint. It includes a high-quality aluminum rip fence that can be easily adjusted to ensure straight cuts. The onboard measuring scale is clear and easy to read, allowing users to set cuts accurately. The fence locks securely in place, providing peace of mind during operation.

Safety is paramount when working with power tools, and the Grizzly T23091 incorporates several safety features. An accessible blade guard protects users from accidental contact with the saw blade while ensuring a clear view of the cutting line. The push stick and miter gauge included with the saw further enhance user safety by promoting proper cutting techniques.

Moreover, the T23091 features an integrated dust collection port. This allows for improved cleanliness in the workspace, helping to minimize debris and sawdust during operation. Users can connect a shop vacuum or dust collector for enhanced efficiency in maintaining a tidy work environment.

In terms of technology, the Grizzly T23091 is designed for ease of use, with intuitive controls that cater to both beginner and experienced users. The tool's durable construction ensures longevity, making it a worthwhile investment for anyone serious about woodworking.

In conclusion, the Grizzly T23091 combines power, precision, and safety features in one user-friendly package. Its strong motor, robust design, and thoughtful technology make it a reliable choice for achieving professional-quality results in woodworking projects.
Top Page Image Contents