Cisco Systems CISCO881SECK9 manual Configuring the ATM CPE Side, Pvc name vpi/vci

Page 32

Chapter 3 Basic Router Configuration

Configuring WAN Interfaces

Configuring the ATM CPE SIDE

Perform the following steps to configure the ATM CPE side, starting in global configuration mode.

SUMMARY STEPS

1.interface type number

2.no shutdown

3.interface atm0.1 point-to-point

4.ip address ip-address mask

5.ppvc [name] vpi/vci

6.protocol protocol {protocol-address[virtual-template] inarp} [[no] broadcast disable-check-subnet [no] enable-check-subnet]

7.end

DETAILED STEPS

	Command		Purpose

Step 1	interface type number		Enters configuration mode for the ATM
	Example:		WAN interface (ATM0).
	Example:
	Router (config) # interface atm0

Step 2	no shutdown		Enables the configuration changes to
	Example:		the ATM interface.
	Example:
	Router (config-if) # no
	shutdown
	Router (config-if) #

Step 3	interface atm0.1 point-to-point		Enables the ATM0.1 point-to-point
	Example:		interface.
	Example:
	Router (config-if) # interface
	ATM0.1
	point-to-point
	Router (config-subif) #

Step 4	ip address ip-address mask		Enters IP address and subnet mask.
	Example:
	Router (config-subif)# ip address
	30.0.0.1	255.255.255.0

Step 5	pvc [name] vpi/vci		Creates or assigns a name to an ATM
	Example:		PVC and enters the ATM virtual circuit
	Example:		configuration mode.
	Router (config-subif) # pvc 13/32		configuration mode.
	Router (config-subif) # pvc 13/32
	Router (config-if-atm-vc) #

3-12	Cisco 880 Series Integrated Services Router Software Configuration Guide
	OL-22206-01

Image 32

Contents Americas Headquarters Page Objective AudienceOrganization ConventionsChapters Convention Description Boldface fontRelated Documentation Searching Cisco DocumentsObtaining Documentation and Submitting a Service Request Models of the Cisco 880 Series ISRs General DescriptionCisco 880 Series ISR Common Features Port 10/100 FE LAN Switch802.11b/g/n Wireless LAN Battery-backed-up Real-Time ClockSelecting Feature Sets LicensingC881W C886VA-WMB memory MB Flash C887VA-WC881GW Memory C887GWOn Board Memory 1st core 2nd core Flash sizeLED Overview Color Description IndicationFE/GE LAN/WAN Steady on= linkVpnok PppokPower Supply Images supportedMinimum software version needed to support AP802 Software Minimum versionTBD MR2OL-22206-01 Wireless Device Overview Software ModesManagement Options Network Configuration Examples Root Access PointCentral Unit in an All-Wireless Network Access pointBasic Router Configuration Router Interface Port Label Default ConfigurationInterface Ports Basic Router Configuration Default Configuration Information Needed for Configuration Configuring Command-Line Access Command PurposeLine aux console tty vty line-number ExampleCommand Purpose ExampleConfiguring Global Parameters Configuring WAN InterfacesTerminal, use the following Hostname name Specifies the name for the router ExampleConfiguring a Fast Ethernet WAN Interface Configuring a VDSL2 WAN InterfaceNo shutdown Exit Controller vdsl Shutdown No shutdown Exit ShutdownConfiguring Adsl Mode 1shows an ATM WAN or Ethernet WAN network topographyVerifying CPE to Peer Connection for Adsl Configuring Adsl Auto ModeConfiguring CPE and Peer Adsl Mode Pvc name vpi/vci Configuring the ATM CPE SideNo shutdown Interface atm0.1 point-to-point Adsl Configuration Example Command Purpose StepConfigures a static map for an ATM Virtual-template inarp noNo fair-queue Verifying Adsl Configuration ATMVerifying CPE to Peer Connection for Adsl Configuring the Fast Ethernet LAN InterfacesConfiguring the Wireless LAN Interface Configuring a Loopback Interface Another way to verify the loopback interface is to ping it Configuring Static RoutesVerifying Configuration Verifying Configuration ExampleConfiguring Dynamic Routes Configuring Routing Information ProtocolNo auto-summary Configuring Enhanced Interior Gateway Routing Protocol Router eigrp as-numberBasic Router Configuration Configuring Dynamic Routes OL-22206-01 Basic Wireless Device Configuration Starting a Wireless Configuration Session Interface wlan-ap0Service-module wlan-ap 0 session Wireless Device Control-Shift-6 x Router DisconnectConfiguring Wireless Settings Cisco Express SetupCisco IOS Command Line Interface Configuring the RadioConfiguring Wireless Security Settings Configuring Access Point as Local AuthenticatorConfiguring WEP and Cipher Suites Assigning SSIDsInstructions Security Type Description Security Features EnabledSecurity Types Configuring Wireless Quality of Service EAP1PEAP3, EAP-TLS4, EAP-FAST5, EAP-TTLS6, EAP-GTC7 WPA9Configuring the Access Point in Hot Standby Mode Preparing for the UpgradeUpgrading to Cisco Unified Software Software PrerequisitesConfirm that the Mode Setting is Enabled Performing the UpgradeSecure an IP Address on the Access Point Upgrading AP bootloader Downgrading the Software on the Access PointRecovering Software on the Access Point Wireless OverviewNetwork Design Links Security LinksLWAPP1 Wireless LAN Controllers Administering LinksWhy Migrate to the Cisco Unified Wireless Network? Lwapp Wireless LAN Access Points Home.html