Craftsman 315.175341 To Remove the Fixed or D-HANDLE Base, Unplug the router

Page 10

_, WARNING: Never connect the router to power supply when you are assembling parts, making adjustments, installing or removing cutters, or when not in use. Disconnecting the router prevents accidental starting that could cause serious injury.

REMOVING AND INSTALLING THE ROUTER

BASE

TO SWITCH FROM THE FIXED BASE OR D-HANDLE BASE TO THE PLUNGE BASE

See Figures 2 and 3.

TO REMOVE THE FIXED OR D-HANDLE BASE:

1. Unplug the router,

,_ WARNING: Failure to unplugthe tool could result in accidental starting causingserious.

2.Place the router upside down with the Craftsman label away from you.

3.Loosen the locking arm on the base.

4.Depress and hold the gold spindle lock button. The gold spindle lock button will not depress fully unless it is in line with the hole in the collet.

5.Ifthe goldspindle lockbuttondoes not depressfully,turn the colletnut while depressingthe goldspindle lock button.As they align,the gold spindlelock buttonwill depressfully.

6.Turn the depth adjusting ring counterclockwise until the motor is to its highest position. NOTE: As the motor is rising, the gold spindle lock button has to be depressed until it clears the rear window.

7.Align the indicator arrow on the depth adjustment ring with the indicator point on the base.

8.Pull the base until it dislodges from the motor housing.

TO INSTALL THE PLUNGE BASE

1.Unplug the router.

2.Place the plunge base on a flat surface.

3.Loosen the locking knob.

4.Align the groove in the motor housing with the rib inside the base. NOTE: The rib is located on the inside of the base in line with the handle.

5.Depress and hold the gold spindle lock button.

6.Slide the motor housing into the base.

7.Tighten the locking knob.

_, CAUTION: Do not tighten the locking knob without the motor installed in the base. Failureto heed this

caution may resultin permanent damage to the

lockingmechanism.

GOLD

SPINDLE

LOCK

BUTTON

ADJUSTMENTLOCKING

RINGARM

INDICATORDEPTHADJUST-

MENTRING

INDICATOR

 

POINT

Fig. 2

GROOVEIN

HOUSINGMOTOR..

RIBINSIDE

THE BASE

@

Fig. 3

10

Image 10
Contents Router Full ONE Year Warranty on CRRFT$1vlRH Router Work Area Electrical SafetyTool USE and Care When servicing a tool, use only identical replace ServiceAdditional Safety Rules Symbol DESIGNATION/EXPLANATIONService Symbol MeaningExtension Cords Double InsulationElectrical Connection 100Switch Motor Housing Goldspindle Lockbutton Product SpecificationsSwitch Know Your RouterPacking List Carefully remove the tool and the accessoriesfrom the boxRouter Motor Wrench OperatorsManual To Remove the Fixed or D-HANDLE Base Unplug the routerDepth Adjustment Ring To Switch from Plunge Base to Fixed Base or D-HANDLE BaseTo Install the Fixed or D-HANDLE Base Indicator ArrowREMOVING/INSERTING cunERS Causing serious personal injuryAdjusting Depth of CUT To remove the cutter Remove the cutter from the colletLock the plunge lock lever Stop Plunge Lock BAR Lever KnobCutter Locking ARM To Adjust Depth of CUT for Fixed Base RoutersPoint Ring Operating the Router See Figures 16Feedguide Feeding the RouterRotation Rotation FeedRate of Feed Feeding Too Slow See Figure2ND 1ST Depth of CUTPass CUi-rERS Adjusting Locking ARM TensionGeneral LubricationPanel BIT Straighi COMBI-VEININGI Core Straight Combi HingeNation BIT BOX Face Nation Mortising Cutter BIT BevelPage Seenote Craftsman Router Motor Model NumberKey Part Description Qty 690141001 See Back page for Parts Ordering Instructions671457001 Your Home Call anytime, day or night U.SA and Canada