Grizzly G1066Z, G1079 instruction manual Length AMP Rating

Page 5

Safety Instructions For Power Tools

9.USE PROPER EXTENSION CORD. Make sure your extension cord is in good condi- tion. Conductor size should be in accor- dance with the chart below. The amperage rating should be listed on the motor or tool nameplate. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Your extension cord must also contain a ground wire and plug pin. Always repair or replace exten- sion cords if they become damaged.

Minimum Gauge for Extension Cords

 

 

LENGTH

 

 

 

 

 

 

AMP RATING

25ft

 

50ft

100ft

 

 

 

 

 

0-6

18

 

16

16

 

 

 

 

 

7-10

18

 

16

14

 

 

 

 

 

11-12

16

 

16

14

 

 

 

 

 

13-16

14

 

12

12

 

 

 

 

 

17-20

12

 

12

10

21-30

10

 

10

No

 

 

 

 

 

10.WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is recommended. Wear protective hair cov- ering to contain long hair.

11.ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty. Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.

12.SECURE WORK. Use clamps or a vise to hold work when practical. It’s safer than using your hand and frees both hands to operate tool.

13.NEVER OVERREACH. Keep proper foot- ing and balance at all times.

14.MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories.

15.DISCONNECT TOOLS before servicing and changing accessories, such as blades, bits, cutters, and the like.

16.REDUCE THE RISK OF UNINTENTION- AL STARTING. Make sure switch is in off position before plugging in. Also, the mag- netic switch on this machine may start if the switch gets bumped hard enough.

17.USE RECOMMENDED ACCESSORIES. Consult the owner’s manual for recom- mended accessories. The use of improper accessories may cause risk of injury.

18.CHECK DAMAGED PARTS. Before fur- ther use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, bind- ing of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.

19.NEVER LEAVE TOOL RUNNING UNAT- TENDED. TURN POWER OFF. Do not leave tool until it comes to a complete stop.

20.NEVER USE UNDER THE INFLUENCE of alcohol or drugs, or when tired.

21. NEVER ALLOW UNSUPERVISED OR

UNTRAINED PERSONNEL TO OPER- ATE THE MACHINE. Make sure any instructions you give in regards to the oper- ation of the machine are approved, correct, safe, and clearly understood.

G1066/G1066Z/G1079 Drum Sander

-3-

Image 5
Contents Model G1066/G1066Z/G1079 Drum SanderPage Table Of Contents Safety Instructions For Power Tools SafetyLength AMP Rating Additional Safety Instructions For The Drum Sander Circuit Requirements 220V Single-Phase GroundingExtension Cords Wiring Diagram Commentary General InformationUnpacking Piece Inventory Hardware Recognition Chart Site Considerations Clean UpBeginning Assembly Dust Ports AssemblySetscrew Crank Handle G1066Z Control PanelDrum Alignment AdjustmentsModel G1066Z rear drum Adjustment control G1066/G1066Z/G1079 Drum Sander Pressure Rollers Dust Scoop Belt To change the paper Disconnect the machine from the power Paper Replacement G1066/G1079Important Tips For Changing Sandpaper Paper Replacement G1066ZDust Collection Conveyor Belt Operations Test Run G1066/G1079 Variable Speed Hook & Loop Sandpaper Choosing SandpaperLubrication MaintenanceGeneral Matching bearing tab to notch Bearing ReplacementClosure Machine Data Sheet G1066 Stand & Table Elevation G1066 Feed Belt & Table G1066 Drum & Roller Mechanism G1066 Parts List G1066/G1066Z/G1079 Drum Sander Model G1066Z Drum Sander W/VARIABLE Speed Conveyor G1066Z G1066Z G1066Z Flat Washer 1⁄2 PN04M G1066/G1066Z/G1079 Drum Sander Model G1079 16 Drum Sander G1079 Stand & Table Elevation G1079 Feed Belt & Table G1079 Drum & Roller Mechanism G1079 Parts List G1066/G1066Z/G1079 Drum Sander Troubleshooting Guide Maintenance Notes Warranty and Returns Warranty Card Grizzly INDUSTRIAL, INC