Grizzly instruction manual Circuit Requirements, G0449 G0450 at

Page 13

SECTION 2: CIRCUIT REQUIREMENTS

G0449		G0450 at 220V

Serious personal injury could occur if you connect the machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so.

Amperage Draw

The 10 HP motor on the Model G0449 will draw the following amps:

Main Motor	............................................44	Amps
Feed Motor	...........................................21/2	Amps

Circuit Requirements

Only connect your machine to a circuit that meets the requirements below. Always check to see if the wires and circuit breaker in your circuit are capable of handling the amperage draw from your machine, as well as any other machines that could be operating on the same circuit. If you are unsure, consult a qualified electrician.

Minimum Circuit Requirement

60 Amp

Minimum Cord Requirements

A cord is not provided with your machine. For 220V single-phase operation, use the following type of cord (not to exceed 50 ft.):

Cord	3 wire
Gauge	4 Gauge

A fire may occur if your particular electrical configuration does not comply with local and state codes. The best way to ensure compli- ance is to check with your local municipality or a qualified electrician.

G0449/G0450 37" Drum Sander

Serious personal injury could occur if you connect your machine to the power source before you have completed the set up pro- cess. DO NOT connect the machine to the power source until instructed to do so.

220V Pre-Wired

The Model G0450 is prewired for 220V 3-phase operation, but can be rewired for 440V 3-phase operation if needed.

Amperage Draw

The Model G0450 has a 15 HP motor that will draw the following amps at 220V 3-phase:

Main Motor at 220V	...............................40	Amps
Feed Motor at 220V	.............................. 1.3	Amps

Circuit Requirements

Only connect your machine to a circuit that meets the requirements below. Always check to see if the wires and circuit breaker in your circuit are capable of handling the amperage draw from your machine, as well as any other machines that could be operating on the same circuit. If you are unsure, consult a qualified electrician.

Minimum Circuit Requirement 220V

60 Amp

Minimum Cord Requirements

A cord is not provided with your machine. For 220V 3-phase operation, use the following type of cord (not to exceed 50 ft.):

Cord	4 wire
Gauge	4 Gauge

-11-

Image 13

Contents Model G0449/G0450 Drum SanderPage Table of Contents Service Foreword IntroductionContact Info Machine Data Sheet Model G0450 Drum Sander Front view, Model G0449 IdentificationControl panel close-up Control PanelSafety SafetyInstructions for Machinery Always Lock Mobile Bases if Used Before Operating Machinery Safety Instructions for MachineryAdditional Safety for Drum Sanders G0449 G0450 at Circuit RequirementsPhase Converter With G0450 G0450 at Power ConnectionExtension Cords Grounding Rewiring toSet Up Safety SET UPItems Needed For Set Up UnpackingSite Considerations InventoryInventory Figure Qty ToolsMounting Control Panel Attaching Top CoverComponents and Hardware Needed Qty To attach the top cover to the drum sanderMounting to Floor Placing SanderDust Collection Installing HandwheelTo mount the handwheel To connect the dust ports to a dust collectorTo connect the sander to the power source Power CordGear Oil Check To check the gear oilTest Run Recommended AdjustmentsOperations Operation Safety Depth of CutTo set the depth of cut Variable Speed Sanding To adjust the conveyor speedChoosing Sandpaper Sanding TipsGrit Class Usage To change the paper Disconnect the machine from the power Paper ReplacementTools Needed Qty PRO-STICKSanding Pad AccessoriesSize Cleaning MaintenanceSchedule LubricationWorm gear threads About Service ServiceTroubleshooting Reduce rear pressure roller pressure Gauge Blocks Belt ServiceTo make the gauge blocks To align the pulleys Disconnect power to the sander To adjust V-belt tension Disconnect power to the sanderLoosen BeltsTo tension the conveyor Conveyor Tensioning TrackingTo track the conveyor To align the drums Disconnect power to the sander Drum AdjustmentsPage Page Pressure Roller Factory SettingHeight Scale Pointer Calibration Setting Distance From Roller 160 4mmDust Scoop Position Tools Needed Qty Phillips Head ScrewdriverTable Lift Screws To replace the conveyor belt Disconnect power to the sander Conveyor Belt ReplacementTo Step To Step To Step Model G0449 Electrical panel G0449/G0450 37 Drum Sander G0449 Electrical ComponentsG0449 Wiring Diagram G0450 back side of front panel G0450 220V 3 Phase Electrical ComponentsG0450 220V 3 Phase Wiring Diagram G0450 440V back side of front panel G0450 440V 3 Phase Electrical ComponentsG0450 440V 3 Phase Wiring Diagram Frame Parts Breakdown Description Frame Parts ListBreakdown Conveyor Parts List Roller Phillips Screwdriver Roller and Drum Parts ListWarranty and Returns Comments Warranty CardBOX BELLINGHAM, WA Grizzly INDUSTRIAL, INCPage Call Today For a Free Full Color Catalog