Delta 31-750 Additional Safety Rules For Random Orbital Sanders, Packing a N D Cleaning

Page 4

ADDITIONAL SAFETY RULES

FOR RANDOM ORBITAL SANDERS

1. W ARNING: D O N O T operate your random orbital sander until it is completely assembled and installed according to the instructions.

2.IF Y O U A R E N O T thoroughly familiar with the oper- ation of the random orbital sander, obtain advice from your supervisor, instructor or other qualified person.

3.USE FA C E O R DUST MASK. WARNING: The dust generated by certain woods and wood products can be injurious to your health. ALW AYS operate machinery in well-ventilated areas and provide for proper dust removal. USE wood dust collection systems whenever possible. Sanding of Lead-based paintis N O T RECOMMENDED.

4.KEEP fingers away from rotating abrasive disc.

5.M A K E SURE abrasive disc is not damaged and is properly secured on the disc plate before operating.

6.NEVER perform layout, assembly or set-up work on thetable while the sander is operating.

7.M A K E SURE workpiece is clear of abrasive disc before turning unit on.

8.KEEP W O R K AREA CLEAN. Cluttered areas can create slipping or tripping hazards.

9.DON T FORCE TO O L. It will do the job better and be safer at the rate for which it was designed.

10.NEVER use machine for wet sanding which can create hazard of electrical shock.

11.USE correctly sized abrasive disc. Maintain minimum table opening to keep fingers from being pinched or workpiece being pulled down.

12.D O N O T sand near flammable liquids, vapors, or gases.

13.ALW AYS support workpiece on work table. USE sander on a solid supporting surface where there is plenty of room for handling and supporting workpiece.

14.CLEAR all debris from table before sanding the workpiece.

15.D O N O T use this sander to sand pieces too small to be held safely and securely by hand.

16.ALW AYS W E A R PROPER EYE PROTECTION.

17.THE USE ofattachments and accessories not recom- mended by Delta may result in the risk of injuries.

18.PROTECT Y O U R EARS. W ear proper hearing pro- tection.

19.AFTER turning off power switch, disconnect tool from power source and wait for sander to stop before servicing.

20.D O N O T wear gloves, neckties, jewelry or loose clothing.

21.MAINTAIN minimum clearance between abrasive disc and fence.

22.AVOID KICKBACKS by sanding left of disc center, holding workpiece firmly, and using support fence when possible.

23.KEEP hands and fingers out of dust chute.

24.D O N O T expose to rain or use in damp locations.

25.DISCONNECT MACHINE F R O M P O W E R SOURCE BEFORE MAKING REPAIRS O R ADJUSTMENTS.

26.ADDITIONAL INFORMATION regarding the safe and proper operation of this product is available from the National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201, in the Accident Prevention Manual for Industrial Operations and also in the Safety Data Sheets provided by the NSC. Please also refer to the American National Standards Institute ANSI 01.1 Safety Require- ments for Woodworking Machinery and the U.S. Depart- ment of Labor OSHA 1910.213 Regulations.

27.S AVE THESE INSTRUCTIONS.Refer to them often and use them to instruct others.

U N PACKING A N D CLEANING

Your new random orbital sander is shipped complete in one container.Carefully unpack the sander and all loose items from the shipping container. Clean all loose parts. Fig. 2, illustrates the sander and all loose parts supplied with the machine. If you purchased the accessory Model 50-780 Stand, Fig. 3 illustrates the components of the stand.

ASSEMBLY INSTRUCTIONS

W ARNING: F O R Y O U R O W N SAFETY, DO N O T CONNECT THE SANDER TO A P O W E R S O U R C E UNTIL THE MACHINE IS COMPLETELY ASSEMBLED A N D Y O U H AV E R E A D A N D UNDERSTO O D THE ENTIRE O W N E R S MANUAL. NOTE: Place the machine on a firm supporting surface and proceed with the assembly instructions. If you purchased the accessory 50-780 Steel Stand, this manual also contains instructions for its assembly.

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Bench Random Orbital Sander Table O F Contents Keep Guards in Place and in working order Safety RulesALW AYS W E a R EYE Protection Additional Safety Rules For Random Orbital Sanders Packing a N D CleaningAssembly Instructions ALW AYS W E a R Proper EYE ProtectionDust Bag Fence Fence Lock Knob13MM and 14MM W rench Not shown Four Legs 27-1/2 long 21-5/16 longAdjusting Table Assembling Abrasive Discs to Disc PlateTighten four lock nuts F , after table height adjustment Assembling Fence To TableAssembling Dust B a G Assembling a C C E S S O RY 50-780 STA N DAccessory 31-752 Disc Holder TOR SpecificationsExtension Cords Grounding InstructionsRepair or replace damaged or worn cord immediately E R Ating Controls and Adjustments Locking Switch OFF PositionStarting a N D Stopping Sander Changing Abrasive DiscsPlease Read the Safety Rules Before Operating the Sander E R Ations

31-750 specifications

Delta 31-750 is a robust and versatile power tool designed specifically for professional woodworkers and serious DIY enthusiasts. This table saw stands out in its class due to its impressive blend of power, precision, and innovative features, making it a favored choice for tackling a wide range of cutting tasks.

At the heart of the Delta 31-750 is a potent 3-horsepower motor that delivers exceptional cutting capacity and efficiency. This motor provides the necessary torque to handle thick hardwoods and dense materials without bogging down. Coupled with a specially designed belt-driven system, the unit ensures smooth operation and reduced vibrations, contributing to a more stable and accurate cutting experience.

One of the standout features of the Delta 31-750 is its large cast iron table, which offers a generous working surface. With dimensions of 30 inches by 40 inches, it provides ample space for handling large sheets of material. The table's flatness is crucial for achieving precise cuts, and Delta has ensured that this surface remains true for accurate woodworking.

In addition to its expansive table, the Delta 31-750 incorporates a high-quality blade with a precision fence system. The quick-release fence allows for easy adjustments, ensuring that users can switch between different cutting tasks swiftly. With a maximum rip capacity of over 30 inches, this table saw is well-suited for making large cuts with minimal effort.

Another advantageous characteristic is its dust collection system, which helps maintain a clean workspace. An integrated port allows for easy attachment to a shop vacuum, efficiently removing sawdust and debris during operation. This feature not only promotes cleanliness but also enhances visibility and safety while working.

The Delta 31-750 is equipped with advanced safety features, including a blade guard and anti-kickback pawls. These elements help minimize the risk of accidents while using the saw, making it a safer option for users of all experience levels.

Overall, the Delta 31-750 is a top-tier choice for those seeking a powerful, reliable, and feature-rich table saw. With its combination of performance, safety, and ease of use, this tool continues to be a favorite among woodworking professionals, making it a worthy investment for anyone serious about their craft.
Top Page Image Contents