Schumacher IP-1875C owner manual Follow These Steps When connecting to a Battery

Page 8

6.FOLLOW THESE STEPS WHEN connecting to a BATTERY

A SPARK NEAR THE BATTERY MAY CAUSE A

BATTERY EXPLOSION. TO REDUCE THE RISK

OF A SPARK NEAR THE BATTERY:

6.1Attach the output cables to the battery and chassis as indicated below. Never allow the output clips to touch each other.

6.2Position the DC cables to reduce the risk of damage by the hood, door and moving or hot engine parts. NOTE: If it is necessary to close the hood during the jump starting process, ensure that the hood does not touch the metal part of the battery clips or cut the insulation of the cables.

6.3Stay clear of fan blades, belts, pulleys and other parts that can cause injury.

6.4Check the polarity of the battery posts. The POSITIVE (POS, P, +) battery post usually has a larger diameter then the NEGATIVE (NEG, N, -) post.

6.5Determine which post of the battery is grounded (connected) to the chassis. If the negative post is grounded to the chassis (as in most vehicles), see step 6.5. If the positive post is grounded to the chassis, see step 6.6.

6.6For a negative-grounded vehicle, connect the POSITIVE (RED) clip from the battery Instant Power™ to the POSITIVE (POS, P, +) ungrounded post of the battery. Connect the NEGATIVE (BLACK) clip to the vehicle chassis or engine block away from the battery. Do not connect the clip to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.

6.7For a positive-grounded vehicle, connect the NEGATIVE (BLACK) clip from the battery Instant Power™ to the NEGATIVE (NEG, N, -) ungrounded post of the battery. Connect the POSITIVE (RED) clip to the vehicle chassis or engine block away from the battery. Do not connect the clip to the carburetor, fuel lines or sheet-metal body parts. Connect to a heavy gauge metal part of the frame or engine block.

6.8When disconnecting the Instant Power™, turn all switches to off (if applicable), remove the clip from the vehicle chassis and then remove the clip from the battery terminal.

7.Charging and ac power cord connections

RISK OF ELECTRIC SHOCK OR FIRE.

7.1The Instant Power™ charger is for use on a nominal 120-volt circuit. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances. The plug pins must fit the receptacle (outlet). Do not use with an ungrounded system. NOTE: Pursuant to Canadian Regulations, use of an adapter plug is not allowed in Canada. Use of an adapter plug in the United States is not recommended and should not be used.

• 4 •

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Advertencia Do not Return this Product To the Store Table of Contents Section Índice Sección PàginaBATTERY. Must be Disposed of Properly Table DES MatièresPartie Contains Sealed NON-SPILLABLE LEAD-ACIDRisk of Electric Shock or Fire Risk of Explosive Gases Preparing to use the Instant Power Instant power LocationRisk of Explosion and Contact with Battery Acid DC Connection PrecautionsFollow These Steps When connecting to a Battery Charging and ac power cord connectionsFeatures Charging the Internal Battery using the Built-In ChargerPowering a 12V DC Device Operating InstructionsJump Starting a Vehicle Engine Risk of ExplosionUsing the Built-In Light Using the Air Compressor Risk of explosionAppliance Type Estimated Wattage Estimated Usage Time Estimated Time for InflatingMaintenance Instructions Troubleshooting Problem Possible Cause REASON/SOLUTIONMoving and Storage Instructions Charge Immediately After Purchase Keep Fully ChargedProblem Possible Cause REASON/SOLUTION SpecificationsReplacement PARTS/accessories Before Returning for RepairsDo not Return this Product to the Store Mount Prospect, IL Mail ToBusiness Center Drive Inscription AU Programme DE Garantie Limi TÉE DE 1 AN Atención EL Riesgo DE Descarga Eléctrica O IncendioRiesgo DE Gases Explosivos Preparación Para EL USO DEL instant power Ubicación DEL Instant powerRiesgo DE Contacto CON EL Ácido DE LA Batería Precauciones DE Conexión EN CCPage Características Indicador LEDInstrucciones DE Operación Para arrancar el motor del vehículoRiesgo de Explosión Para hacer funcionar un aparato de 12V de CDUso de la Luz adjunta Uso del Compresor de Aire Riesgo de explosiónInstrucciones para el manejo y almacenamiento Tiempo estimado para inflarInstrucciones DE Mantenimiento Antes DE Devolver a Reparaciones Especificaciones REPUESTOS/accesorios¡NO LO Devuelva este producto a LA Tienda Risque DE Choc Électrique OU D’INCENDIE Risque DE GAZ Explosifs Précautions Personnelles Risque DE GAZ ExplosifsLE Risque DE Contact Avec L’ACIDE DE Batterie Prépare pour utiliser le Instant powerEmplacement DU Instant power Charge l’alimentation CA et les connexions du cordon Précautions SUR LA Connexion C.CSuivi ces démarches lors de la connexion à une batterie Charge de la batterie interne à l’aide du chargeur intégré Chargement DE LA Batterie Interne DE L’ Instant PowerCaractéristiques Alimenter un appareil 12 V CC Consignes D’UTILISATIONRisques d’explosion Utilisation de la lampe intégrée Utilisation du compresseur d’air Risques d’explosionInstructions de transport et stockage Durée estimée de gonflageConsignes D’ENTRETIEN Tableau DE Dépannage Problème Cause Possible RAISON/SOLUTION Avant DE L’ENVOYER Pour Réparation16. Pièces DE RECHANGE/accessoires NE PAS Retourner LE Produit AU Magasin Page Do not Return this Product To the Store
Related manuals
Manual 8 pages 1.63 Kb

IP-1875C specifications

The Schumacher IP-1875C is a powerful, versatile power inverter that is designed to meet a wide range of power needs. With its robust construction and advanced technology features, it provides reliable performance for those who require electricity in remote locations or during emergencies. This inverter is particularly popular among campers, road trippers, and individuals who seek backup power systems for their homes.

One of the key features of the Schumacher IP-1875C is its impressive power output. With a peak power of 3750 watts and a continuous output of 1875 watts, this inverter can handle various devices, from small electronics to larger appliances. This makes it ideal for use with items like televisions, microwaves, and power tools. The inverter is equipped with three AC outlets, allowing users to power multiple devices simultaneously, enhancing its usability in various situations.

The Schumacher IP-1875C also integrates advanced safety technologies to protect both the inverter and the devices connected to it. It features built-in protections against overloads, short circuits, and overheating, ensuring that users remain safe while using the product. An LED indicator is included to inform users about the operational status of the inverter, making it user-friendly.

In terms of portability, the Schumacher IP-1875C is designed for easy transportation. Its compact design and lightweight construction make it convenient for activities like camping, tailgating, or prolonged stays in remote locations. The inverter can be powered by a car battery or directly from a 12V source, adding to its versatility.

The unit also operates with a low noise level, a significant advantage when compared to traditional generators, making it ideal for use in quiet settings. The inverter's construction is designed for durability, capable of withstanding the rigors of outdoor conditions and transport.

Overall, the Schumacher IP-1875C stands out as a reliable power source combining power, safety, and portability. Whether for recreational activities, emergency situations, or routine use, it caters to diverse demands, making it a practical solution for modern power needs. With its impressive features and technologies, this inverter provides peace of mind and convenience for users, making it a worthy investment for anyone in need of portable power.
Top Page Image Contents