Schumacher 6000A owner manual Using the BUILT-IN Battery Tester

Page 10

USING THE BUILT-IN BATTERY TESTER

OVERVIEW

The SpeedCharge has a built-in battery tester that displays either an accurate battery voltage or an estimate of the battery’s relative charge based on the battery voltage and the Battery Council International scale.

TESTING SEQUENCE

There are four basic steps required to use the 6000A as a battery tester.

1.Connect the SpeedCharge battery clamps to the battery. Be sure to follow all of the precautions listed under

“OPERATING INSTRUCTIONS”.

2.Connect the SpeedCharge power cord to a 120 VAC outlet. Again, be sure to follow all of the precautions listed under

“OPERATING INSTRUCTIONS”.

3.If necessary, press the Battery Type button until the correct type is indi- cated.

4.Read the voltage on the digital LED or press the display mode button to set the tester to “Battery %” and read the battery percent.

TESTER AND CHARGER

When first turned on, the 6000A oper- ates only as a tester, not as a charger. To continue to use it as only a tester, avoid pressing the CHARGE RATE switch button. Selecting a charge rate activates the battery charger and deactivates the tester.

POWER-UP IDLE TIME LIMIT

If no switch button is pressed within ten minutes after the unit is first powered up, the unit will automatically switch from tester to charger, if a battery is connected. In that case, the unit will be set for the 2A charge rate and REGU- LAR battery type.

TESTER WITHOUT TIME LIMIT

If either the DISPLAY MODE or BAT- TERY TYPE button is pressed within the first ten minutes after the unit is powered up, the unit will remain a tester (not a charger) indefinitely, unless a charge rate is selected.

TESTINGAFTERCHARGING

After the unit has been changed from tester to charger (by selecting a charge rate), it remains a charger as long as it has power. Disconnect and reconnect the power to change the unit back to a tester.

TESTERSTATUSLEDs

When the 6000A is operating as a battery tester, the status LEDs light under the following conditions.

•The CHARGED (green) LED will light if a charged battery is tested.

•The CHARGING (yellow) LED does not light in the battery test mode.

•The CHECK (red) LED lights unless a properly connected battery is de- tected.

•When the tester display mode is set to voltage, none of the Status LEDs light (it could be testing a battery or an alternator).

INITIAL PERCENT CALCULATION When a battery % is calculated for the first time after connecting a battery, the digital LED will show two dashes (“--”) for a period as long as several seconds while the tester analyzes the battery.

NOTES FOR TESTING BATTERY %

A recently charged battery could have a temporarily high voltage due to what is known as “surface charge”. The voltage of such a battery will gradually drop during the period immediately after the charging system is disengaged. Consequently, the tester could display inconsistent values for such a battery. For a more accurate reading, the surface charge should be removed by temporarily creating a load on the battery, such as by turning on lights or other accessories.

The battery % ranges from 0 to 100.

The battery tester is only designed to test batteries. Testing a device with a rapidly changing voltage could yield unexpected or inaccurate results.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Send Warranty Product Repairs to SpeedChargeTable of Contents Important Safety Instructions Help US Help YOUPersonal Safety Precautions Using AN Extension Cord Before Using Your Battery ChargerPreparing Your Battery to be Charged Plugging ITOperating Instructions Charging Battery in the VehicleConnecting to a positive-grounded Negative Grounded SystemCharging Battery Removed from the Vehicle Using Engine StartCharge Rate Switch 6000A Control Panel Display Mode SwitchBattery Type Switch Speedcharge ControlControl Panel Guide Mode of OperationDigital Display Using the BUILT-IN Battery Tester Alternator Testing Notes Using the BUILT-IN Alternator TesterUsing Your Engine Starter StartingsequenceUsing Your Battery Charger Engine Starting Notes30A Charge Rate When set to Charging TipsBattery Percent and Charge Time Maintenance and Care TroubleshootingProblem Possible Cause Solution Limited Warranty

6000A specifications

The Schumacher 6000A is a powerful and versatile battery charger designed for automotive enthusiasts and professionals alike. This unit offers a perfect blend of advanced technology and user-friendly design, making it a staple for maintaining and reviving 12-volt batteries.

One of the standout features of the Schumacher 6000A is its high output of 6000 amps, allowing it to quickly charge even the most depleted batteries. This unit is particularly beneficial for those who often work with larger vehicles, including trucks and SUVs, where traditional chargers may fall short. The robust construction ensures durability, essential for both home garages and professional workshops.

The Schumacher 6000A also incorporates smart charging technology. This includes an automatic shut-off feature that prevents overcharging, safeguarding your battery and extending its lifespan. Furthermore, it uses an intelligent microprocessor that adjusts the charging process based on the battery’s condition, optimizing power delivery for both standard and AGM batteries. This adaptability not only enhances performance but also ensures that various battery types are sufficiently catered to.

Another key characteristic of the Schumacher 6000A is its user-friendly interface. Equipped with an intuitive LED display, users can easily monitor the charging status and battery condition at a glance. The clear visual indicators provide real-time updates, allowing users to stay informed about the process without requiring technical expertise.

Safety is another critical aspect of the Schumacher 6000A. The charger features reverse polarity protection, preventing accidental damage caused by incorrectly connecting the clamps. Additionally, it comes with built-in short-circuit protection, ensuring that users can operate the unit with peace of mind.

Portability is also factored into the design. The charger is compact and lightweight, making it easy to transport and store. With its ergonomic handle, users can easily maneuver the unit when needed.

In summary, the Schumacher 6000A battery charger stands out for its impressive charging capabilities, advanced smart technology, user-friendly features, and robust safety mechanisms. Whether for personal use or professional applications, it is an ideal choice for anyone looking to keep their batteries in top-notch condition. This charger not only meets the demands of modern automotive technology but also ensures reliability and ease of use.
Top Page Image Contents