Cabela's 52-0601 manual Measuring Tape Application, Operating Instructions

Page 6

MEASURING TAPE APPLICATION

WARNING! Before cleaning, assembling or disassembling the Arrow Saw, make sure it is turned OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

The Arrow Saw with Dust Collecting Attachment comes without the Measuring Tape applied. Carefully follow these instructions to apply the Measuring Tape to ensure you get the best results from your Arrow Saw.

1.Place the Arrow Saw on a flat, level, non-skid work surface.

2.Clean the front face of the Base to remove any dirt or grime that may have accumulated during manufacturing.

OPERATING INSTRUCTIONS

WARNING! Before cleaning, assembling or disassembling the Arrow Saw, make sure it is turned OFF and the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE!

READ AND FULLY UNDERSTAND ALL INSTRUCTIONS

AND WARNINGS PRIOR TO USING THIS SAW.

YOUR SAFETY IS MOST IMPORTANT! FAILURE TO

COMPLY WITH PROCEDURES AND SAFE GUARDS WARNING! MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE. REMEMBER: YOUR PERSONAL SAFETY

IS YOUR RESPONSIBILITY!

1. Place the Arrow Saw on a

3.Place the end of a tape measure firmly against the right side of the Cutting Blade. Figure 3

4.Measure 6” (15.2 cm) from the Blade to the back face of the notch in the Shaft Position Bracket.

5.Using the left face of the Shaft Position Bracket as a guide, mark the Base with a pencil.

6.Cut the Measuring Tape at the 5” mark. Figure 3

7.Peel about 4” (10.2 cm) of the backing off of the Measuring Tape exposing the adhesive surface.

Shaft

Position FIGURE 3

Bracket

 

Right Side

Left

Front

Measuring

Face

of

Face

of

Tape

Cutting

of Shaft

Base

 

 

Blade

Position

 

 

 

 

Bracket

 

flat, level work surface.

2. Place the Shaft Position Bracket onto

the Base.

Shaft

 

3. Locate the left face of the Shaft Position

Position

FIGURE 4

Bracket

Bracket at the line on the Measuring Tape

Wing Nut

 

indicating the length of shaft you want to

 

 

cut. For example, if you want to cut a 31”

 

 

long arrow shaft, locate the Shaft Position

 

 

Bracket face at the 31” mark. Figure 4

 

 

4. Secure the Shaft Position Bracket

 

 

to the Base by tightening the Wing Nut.

Bracket

 

Slowly tighten the Wing Nut while firmly

Face

Base

holding the Shaft Position Bracket to

 

 

prevent the Shaft Position Bracket from

 

 

moving.

 

 

8.Line up the 6” indicator line on the Measuring Tape with the left side of the Shaft Position Bracket. The top of the Measuring Tape should be about 1/2” (1.3 cm) below the top of the Base. Carefully apply the Measuring Tape a few inches at a time. Continue peeling off the backing as necessary.

9.Be sure to apply the Measuring Tape level and without air bubbles or creases. Such irregularities will result in inaccurate shaft length measurements.

5. Continue to the “THROUGH CUTS” or

“ROLL CUTS” section of this manual.

CAUTION ROTATING SHARP BLADE! To avoid severe injury keep fingers, hands and other foreign objects clear of the saw opening Blade and Moving Parts of the Arrow Saw. Wear approved Safety Glasses and Kevlar Gloves when using the Arrow Saw.

WARNING!

Be sure to follow ALL SAFETY WARNINGS and precautions that are contained in this instruction manual

before using this

appliance!

CAUTION ROTATING SHARP BLADE! To avoid severe injury keep fingers, hands and other foreign objects clear of the saw opening Blade and Moving Parts of the Arrow Saw. Wear approved Safety Glasses and Kevlar Gloves when using the Arrow Saw.

WARNING!

Be sure to follow ALL SAFETY WARNINGS and precautions that are contained in this instruction manual

before using this

appliance!

-6-

-7-

Image 6
Contents Arrow SAW Arrow SAW Without the Blade Arrow SAW Blade ReplacementComponent List Shield Securely Mounted in PlaceUsing the Spin Testers 17b 17aNever Operate the Arrow SAW General Safety RulesRoll Cuts Without the Blade Shield SecurelyThrough Cuts Mounting Instructions Vacuum Attachment InstructionsRemove the Thumb Screws and Cutting Blade Shield Place the Shaft Position Bracket onto Measuring Tape ApplicationOperating Instructions Bracket at the line on the Measuring Tape