DeWalt DW705 manual Accessories, Bench Mounting, Installing a New Saw Blade Fig

Page 8

English

Accessories

Recommended accessories for use with your tool are available at extra cost from your local service center.

CAUTION: The use of any non-recommended accessory such as dado sets, molding cutters, or abrasive wheels may be hazardous.

If you need assistance in locating any accessory, please contact DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 or call 1-800-4-DEWALT (1-800-433-9258).

Bench Mounting

Holes are provided in all four feet to facilitate bench mounting, as shown in Figure 2. (Two different sized holes are provided to accommodate different sizes of screws. Use either hole, it is not necessary to use both.) Always mount your saw firmly to prevent movement. To enhance the tool’s portability, it can be mounted to a piece of 1/2" or thicker plywood which can then be clamped to your work support or moved to other job sites and reclamped.

NOTE: If you elect to mount your saw to a piece of plywood, make sure that the mounting screws don’t protrude from the bottom of the wood. The plywood must sit flush on the work support. When clamping the saw to any work surface, clamp only on the clamping bosses where the mounting screw holes are located. Clamping at any other point will surely interfere with the proper operation of the saw.

CAUTION: To prevent binding and inaccuracy, be sure the mounting surface is not warped or otherwise uneven. If the saw rocks on the surface place a thin piece of material under one saw foot until the saw sits firmly on the mounting surface.

Installing a New Saw Blade (Fig. 5)

(UNPLUG THE MITER SAW)

DO NOT CUT FERROUS METAL (THAT WITH AN IRON OR STEEL CONTENT) OR MASONRY WITH THIS MITER SAW.

With the saw arm in the upper position, raise the lower guard as far as possible. Loosen (but do not remove) the guard bracket screw, until the guard bracket can be raised enough to permit access to the blade screw. The blade guard will be held in the raised position by the guard bracket screw. Depress the spindle lock button. Use the supplied blade wrench in the other hand to loosen (clockwise) the left hand threaded blade screw.

NOTE: To use the spindle lock, depress the button as shown and rotate the blade by hand until you feel the lock engage. Continue to hold the lock button in to keep the spindle from turning. Remove the blade screw and the blade.

FIG. 1

FIG. 2

REAR

LOWER

GUARD

LOCK

DOWN

PIN

BLADE

WRENCH

LEFT SIDE FENCE CLAMPING

KNOBS SIDE TABLE EXTENSION (SOME MODELS)

OPERATING

HANDLE

GUARD

RIGHT

SIDE

FENCE

MITER

CLAMP

KNOB

MITER

LATCH

MITER

SCALE

BENCH

MOUNTING

HOLES

FIG. 3

BRUSH

TRIGGER

CARRYING

 

INSPECTION

SWITCH

SPINDLE

HANDLE

CAP

 

LOCK

 

 

BEVEL

BUTTON

 

 

 

 

 

STOP

MOTOR

 

 

 

HOUSING

 

 

 

REAR

LOWER

GUARD

LEFT

SIDE

FENCE

MITER

CLAMP

KNOB

MITER

 

 

LATCH MITER

 

DUST

SCALE

BEVEL

 

SCALE

SPOUT

 

 

HAND

BEVEL CLAMP

INDENTATION

 

KNOB

 

 

FIG. 4

 

 

LOCK

 

 

DOWN

 

 

PIN

 

 

55 35

 

50

45

40

 

45

4

Image 8
Contents English DW705 Copyright 2001 Guide D´UTILISATION Manual DE Instrucciones Table of Contents Important Safety Instructions Safety Instructions For All ToolsDouble Insulation Polarized PlugsAdditional Safety Rules For Miter Saws Specifications Optional AccessoriesElectrical Connection Unpacking Your SawBench Mounting AccessoriesInstalling a New Saw Blade Fig Installing Extension Kit AdjustmentsRear Lower Guard Adjustment Transporting the SawFence Adjustment Bevel PointerBevel Stop Turn Off and Unplug the Miter SawBrushes OperationBody and Hand Position see FIG Clamping the WorkpieceTurn Off and Unplug Saw Support for Long PiecesWhen Mitering to the Right When Mitering to the LeftDual Range Miter Scale Vernier ScaleOutside Corner Proper CUT Improper CUTAngle a Miter Scale Kerf Plate Miter ARMInside Corner Cutting Crown MoldingRight Bevel Setting Type of CUTAlternative Method for Cutting Crown Molding Wrong Special Cuts Never Make ANY CUT Unless the Material isMaintenance Full WarrantyDAY no Risk Satisfaction Guarantee Secured on the Table and Against the FenceWHAT’S WRONG? What to DO… Trouble Shooting GuideBe Sure to Follow Safety Rules and Instructions
Related manuals
Manual 52 pages 49 Kb