Patent Notification
Manufactured under one or more of the following U.S. patents:
6,431,040 5,582,089
6,427,570 5,375,495
D454,577 5,285,708
5,819,619 5,199,343 Other patents pending.
Troubleshooting Guide
BE SURE TO FOLLOW SAFETY RULES AND INSTRUCTIONS
TROUBLE! | WHAT’S WRONG? | WHAT TO DO | ||
Saw will not start | 1. Saw not plugged in | 1. | Plug in saw. | |
| 2. | Fuse blown or circuit breaker tripped | 2. | Replace fuse or reset circuit breaker. |
| 3. | Cord damaged | 3. | Have cord replaced by authorized service center. |
| 4. | Brushes worn out | 4. | Have brushes replaced by authorized service center or replace them yourself. Refer to Brushes. |
Saw makes | 1. Dull blade | 1. | Replace blade. Refer to Changing or Installing a New Saw Blade. | |
unsatisfactory cuts | 2. | Blade mounted backwards | 2. | Turn blade around. Refer to Changing or Installing a New Saw Blade. |
| ||||
| 3. | Gum or pitch on blade | 3. | Remove blade and clean with turpentine and coarse steel wool or household oven cleaner. |
| 4. | Incorrect blade for work being done | 4. | Change the blade type. Refer to Saw Blades. |
Blade does not come up | 1. Extension cord too light or too long | 1. | Replace with adequate size cord. Refer to Use Proper Extension Cord under Important Safety | |
to speed |
|
|
| Instructions. |
| 2. | Low house current | 2. | Contact your electric company. |
Machine vibrates excessively | 1. Saw not mounted securely to stand or | 1. | Tighten all mounting hardware. Refer to Bench Mounting. | |
|
| work bench |
|
|
| 2. | Stand or bench on uneven floor | 2. | Reposition on flat level surface. Refer to Familiarization. |
| 3. | Damaged saw blade | 3. | Replace blade. Refer to Changing or Installing a New Saw Blade. |
Does not make accurate | 1. Miter scale not adjusted correctly | 1. | Check and adjust. Refer to Miter Scale Adjustment under Adjustments. | |
miter cuts | 2. | Miter pointer not adjusted correctly | 2. | Check and adjust. Refer to Miter Pointer Adjustment under Adjustments. |
| ||||
| 3. | Workpiece is not perpendicular to table | 3. | Check and adjust fence. Refer to Fence Adjustment under Adjustments. |
| 4. | Workpiece moving | 4. | Clamp workpiece securely to fence or glue 120 grit sandpaper to fence with rubber cement. |
Material pinches blade | 1. Cutting bowed material | 1. | Refer to Bowed Material under Special Cuts. | |
|
| TABLE 1: COMPOUND MITER CUT |
|
| |||
| (POSITION WOOD WITH BROAD FLAT SIDE ON THE TABLE AND THE NARROW EDGE AGAINST THE FENCE) |
| |||||
| 10 |
|
|
|
|
|
|
| 20 |
|
|
|
|
|
|
|
|
|
| 30 |
|
|
|
|
|
|
|
| 40 |
|
|
|
|
|
|
| 50 | SQUARE |
|
|
|
|
|
|
|
| |
ANGLEMITERON SAW | 10 |
|
|
|
| BOX | (ANGLEBOXOFSIDE A) |
|
|
|
|
| |||
20 |
|
|
|
|
| ||
|
|
|
|
|
|
| |
| 30 |
|
|
|
| 60 |
|
|
|
| 40 | 6 |
|
|
|
|
|
| - |
|
|
| |
| 10 |
|
| SIDED |
|
| |
THISSET | 20 |
|
| 50 | BOX |
| ANGLEOF |
|
|
|
|
| |||
30 |
|
|
|
| 70 | ||
|
|
|
|
|
| ||
|
| 8 |
|
|
|
| |
|
|
|
|
|
|
| |
|
| - |
|
|
|
|
|
| 40 | SIDED |
|
|
|
| |
|
|
|
|
|
|
| |
|
|
| BOX | 60 |
|
| |
|
| 50 |
|
|
| ||
|
|
|
|
|
|
| |
|
|
| 60 |
| 70 |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
| 80 |
|
|
|
|
| 70 |
|
|
|
|
|
|
|
| 80 |
|
|
|
|
|
| 80 |
|
|
|