ASSEMBLY
WARNING Recharge only with the charger specified for the battery. For specific charging instructions, read the operator’s manual supplied with your charger and battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body of the tool. Make sure it latches securely into place.
OPERATION
WARNING Always remove battery pack before changing or removing acces- sories. Only use accessories specifically recommended for this tool. Others may be hazardous.
WARNING To reduce the risk of injury, wear safety goggles or glasses with side shields.
Installing Bits
Always remove the battery before inserting or removing bits. Select the proper style and size bit for the job.
This tool is equipped with a spindle lock. The chuck can be tightened with one hand, creating higher grip strengths on the bit.
1.To open the chuck jaws, turn the sleeve in the counterclockwise direction.
When using drill bits, allow the bit to strike the bottom of the chuck. Center the bit in the chuck jaws and lift it about 1/16” off of the bottom.
When using screwdriver bits, insert the bit far enough for the chuck jaws to grip the hex of the bit.
2.To close the chuck jaws, turn the sleeve in the clockwise direction. The bit is secure when the chuck makes a ratcheting sound and the sleeve can not be rotated any further.
3.To remove the bit, turn the sleeve in the coun- terclockwise direction.
NOTE: A ratcheting sound may be heard when the chuck is opened or closed. This noise is part of the locking feature, and does not indicate a problem with the chuck’s operation.
Selecting Drill or Drive Action (Cat. No.
1.To use the drilling mode,
rotate the torque selector collar
until the drill symbol | ap- |
pears in line with the arrow.
2. To use the driving mode ro- 
tate the torque selector collar 
until the desired clutch setting 
appears in line with the arrow. 
The adjustable clutch, when
properly adjusted, will slip at a 
preset torque to prevent driving 
the screw too deep into differ- 
ent materials and to prevent 
damage to the screw or tool. 
Selecting Hammer, Drill or Drive Action (Cat. No. 2702-20)
1.To use the
selector collar until the hammer 
symbol 
appears in line with 
the arrow. Apply pressure to 
the bit to engage the hammer- 
ing mechanism.
NOTE: The number selected 
on the torque selector collar 
has no effect on operation of the drill in hammer mode.
NOTE: When using carbide bits, do not use wa- ter to settle dust. Do not attempt to drill through steel reinforcing rods. This will damage the carbide bits.
2.To use the drilling only mode, rotate the application selector
collar until the drill symbol 
appears in line with the arrow. 
NOTE: The number selected 
on the torque selector collar 
has no effect on operation of 
the drill in drilling mode. 
3.To use the driving screws
mode rotate the application 
selector collar until the drive 
symbol 
appears in line 
with the arrow. Then rotate the 
torque selector collar until the 
desired clutch setting appears 
in line with the arrow. 
The adjustable clutch, when 
properly adjusted, will slip at a preset torque to prevent driving the screw too deep into different materials and to prevent damage to the screw or tool.
The torque specifications shown here are approximate values obtained with a fully charged battery pack.
|
| Cat. No. |
|
|
|
Clutch | in. lbs | Applications |
Setting | ||
Small screws in softwood. | ||
Medium screws in softwood or small | ||
screws in hardwood. | ||
Large screws in softwoods. Medium | ||
screws in hardwood or large screws in | ||
hardwood with pilot hole. |
|
| Cat. No. | |
|
|
| |
Clutch | in. lbs | Applications | |
Setting | |||
Small screws in softwood. | |||
Medium screws in softwood or small | |||
screws in hardwood. | |||
| |||
Large screws in softwoods. Medium | |||
18 | 53 | screws in hardwood or large screws in | |
hardwood with pilot hole. |
NOTE: Because the settings shown in the table are only a guide, use a piece of scrap material to test the different clutch settings before driving screws into the workpiece.
Selecting Speed
The speed selector is on top of the motor housing. Allow the tool to come to a complete stop before changing speeds. See “Applications” for recom- mended speeds under various conditions.
1.For Low speed, push the speed selector to display “1”.
2.For High speed, push the speed selector to display “2”.
Using the Control Switch
The control switch may be set to three positions: forward, reverse and lock. Due to a lockout mecha- nism, the control switch can only be adjusted when the ON/OFF switch is not pressed. Always allow
the motor to come to a complete stop before using | |
the control switch. |
|
For forward (clockwise) |
|
rotation, push in the con- | Reverse |
trol switch from the right Forward | |
side of the tool. Check | Lock |
the direction of rotation | Push to |
before use. | CENTER |
For reverse (counterclockwise) rotation, push in the control switch from the left side of the tool. Check direction of rotation before use.
To lock the trigger, push the control switch to the center position. The trigger will not work while the control switch is in the center locked position. Always lock the trigger or remove the battery pack before performing maintenance, changing accessories, storing the tool and any time the tool is not in use.
WARNING To reduce the risk of injury, always hold or brace securely.
Starting, Stopping and Controlling Speed
1.To start the tool, grasp the handles firmly and pull the trigger.
NOTE: An LED is turned on when the trigger is pulled.
2.To vary the speed, increase or decrease the pressure on the trigger. The further the trigger is pulled, the greater the speed.
3.To stop the tool, release the trigger. Make sure the bit comes to a complete stop before laying the tool down.
Drilling
Place the bit on the work surface and apply firm pressure before starting. Too much pressure will slow the bit and reduce drilling efficiency. Too little pressure will cause the bit to slide over the work area and dull the point of the bit.
If the tool begins to stall, reduce pressure slightly to allow the bit to regain speed. If the bit binds, reverse the motor to free the bit from the workpiece.
4 | 5 |