Craftsman 973.11147 owner manual Important Safety Rules for Battery Tools

Page 4

RULES FOR SAFE OPERATION (Continued)

NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite flam- mable liquids, gases, or fumes.

KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products or any strong solvents to clean your tool.

STAY ALERT. Watch what you are doing and use

common sense. Do not operate tool when you are tired. Do not rush.

CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation.

A guard or other part that is damaged should be propedy repaired or replaced by an authorized service center unless indicated elsewhere in this instruction manual. =.

DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center.

DRUGS, ALCOHOL, MEDICATION. Do not operate tool while under the influence of drugs, alcohol, or any medication.

DRILLING OR DRIVING SCREWS INTO ELECTRICAL WIRING IN WALLS, CEILINGS, OR OTHER AREAS CAN CAUSE THE BIT OR CHUCK TO BECOME ELECTRICALLY LIVE. Do not touch metal parts when drilling into a wall; grasp only the insulated handle(s) or plastic housing when using this tool. Make sure hidden electrical wiring, water pipes, and mechanical hazards are not in the path of the bit when drilling into a wall.

INSPECT FOR and remove all nails from lumber before drilling.

IMPORTANT SAFETY RULES FOR BATTERY TOOLS

Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards

when not using your battery tool or when changing accessories.

USE ONLY THE CHARGER PROVIDED WITH YOUR BATTERY TOOL. Do not substitute any other charger. Use of another charger could cause batteries to explode causing possible serious injury.

DO NOT PLACE BATTERY TOOLS OR THEIR BATTERIES NEAR FIRE OR HEAT. They may explode.

DO NOT CHARGE BATTERY TOOL IN A DAMP OR WET LOCATION.

Your battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F.

Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water, then neutralize with lemon juice or vinegar. If liquid gets in your eyes, flush them

with clean water for at least 10 minutes, then seek immediate medical attention.

If carrying your battery tool at your side, make sure it is not running and your finger is not on the switch. Avoid accidental starting.

SECURE WORK before applying power. NEVER hold workpiece in your hand or across your legs.

WHEN SERVICING USE ONLY IDENTICAL CRAFTSMAN REPLACEMENT PARTS.

IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

SAVE THESE INSTRUCTIONS. This manual

contains important safety and operating instructions for battery charger item number 9-11065 (982033-001).

Before using battery charger, read all instructions and cautionary markings in this manual, on battery charger, and product using battery charger.

AWARNING: To reduce risk of injury, charge only nickel-cadmium type rechargeable batteries. Other types of batteries may burst causing personal injury and damage.

Do not expose charger to rain or snow.

Use of an attachment not recommended or sold by the battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.

To reduce risk of damage to charger body and cord, pull by charger body rather than cord when disconnecting charger.

Make sure cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to damage or stress.

Image 4
Contents OwnersManual Specifications Safety Alert Symbol Symbol MeaningRead ALL Instructions Important Safety Rules for Battery Tools Do not Charge Battery Tool in a Damp or WET LocationImportant Information for Recharging HOT Batteries Battery Charger ShownintoolSwitch Lock SwitchVariable Speed To Remove Battery Pack To Install BAI-FERY PackReversible LatchesBits BIT Storage Area Installing Bits Chuckjaws Chuckbody Drillbit ChuckcollarAdjustable Torque Clutch To Adjust TorqueTo Decrease Torque Adjusting Ring To Increase Level DrillingOverload DrillingChuck Removal Mallet Keyless Chuck JawsTo Retighten a Loose Chuck BatteriesBarerypack Removal Preparation for Recycling Page Parts List See Back PageforpartsorderinginstructionsHomeCentral