DeWalt DC825B manual Package contents, Description fig, Electrical safety

Page 11

EN G L I S H

Use only with DEWALT battery packs, others may burst, causing personal injury and damage.

Do not expose to water.

Have defective cords replaced immediately.

Charge only between 4 °C and 40 °C.

Discard the battery pack with due care for the environment.

Do not incinerate the battery pack

NiMH, NiCd+ and Li-Ion.

Charges NiMH and NiCd battery packs.

Charges Li-Ion battery packs.

See technical data for charging time.

Package contents

The package contains:

1 Cordless Impact Driver/Wrench

2 Battery packs

1Charger

1Instruction manual

1Exploded drawing

NOTE: Battery packs and chargers are not included with N-models.

Check for damage to the tool, parts or accessories which may have occurred during transport.

Take the time to thoroughly read and understand this manual prior to operation.

Description (fig. 1–5)

WARNING: Never modify the power tool or any part of it. Damage or personal injury could result.

INTENDED USE

These heavy-duty impact wrenches/drivers are designed for professional impact screwdriving applications.

The impact function makes this tool particularly useful for driving fasteners in wood, metal and concrete.

DO NOT use under wet conditions or in presence of flammable liquids or gases.

These impact wrenches/drivers are professional power tools. DO NOT let children come into contact with the tool. Supervision is required when inexperienced operators use this tool.

a.Trigger switch

b.Forward/reverse button

c.Sleeve

d.1/4" hex quick-release chuck

e.Detent pin

f.Anvil

g.Worklight

h.Battery pack

i.Battery release buttons

Electrical safety

The electric motor has been designed for one voltage only. Always check that the battery pack voltage corresponds to the voltage on the rating plate. Also make sure that the voltage of your charger corresponds to that of your mains.

Your DEWALT charger is double insulated in accordance with EN 60335; therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by a specially prepared cord available through the DEWALT service organization.

Mains plug replacement (U.K. & Ireland only)

DANGER:

Should your mains plug need replacing and you are competent to do this, proceed as instructed below. If you are in doubt, contact an authorized DEWALT repair agent or a qualified electrician.

Disconnect the plug from the supply.

Cut off the plug and dispose of it safely; a plug with bared copper conductors is dangerous if engaged in a live socket outlet.

Only fit 13 Amperes BS1363A approved plugs fitted with the correctly rated fuse (1).

1035

Image 11
Contents DC820 DC822 DC825 DC827 DC830 DC832 DC835 DC837 DC840 DC845 Page Page Congratulations Technical dataEC-Declaration of conformity Definitions Safety GuidelinesGeneral Power Tool Safety Warnings Labels on tool Safety Instructions for All Impact DrillsResidual risks Important Safety Instructions for All Battery Chargers Chargers Charging ProcedureHot/Cold Pack Delay Important Safety Instructions for All Battery PacksStorage Recommendations Battery Cap figBattery pack fig Labels on charger and battery packDescription fig Package contentsElectrical safety Forward/Reverse Control Button fig Using an extension cableVariable Speed Trigger Switch fig Instructions for useUsage Worklight figQuick-Release Chuck fig Anvil With Detent Pin figProtecting the environment CleaningOptional accessories Rechargeable Battery PackɁ٣ͼޭ ࣛੂੈ͈͒  ߣިۭߝ࠵ऀ+ߜੈأؚܕ ߝΖǹȗܤǽްԬۭߝǧǮ ǸȗܤջΟШՔ ࣚƢۭߝȳࣻ Ӡξ০ৃμҢܤۭͤߝ࠵ऀɁ९Ҍވਜ਼ ը࠵ऀޜ߀եǽੋΥڑڊ݃ ӠξԷҟ࣡ߝɁܤͤࠞݧۭߝ࠵ऀҟьڊ ࣡ߝɁ࣡ߝߞ ࣡ߝǻߣԷҟऑȶң Էҟ০ȶңԵǽȦ߆ײ ࣡ߝɁԦԷҟ০ܤջΟШՔߝݻਸ਼тȶȒࢷܸȘԦ۫ްжμҩੋ͠ ˖ݮӿ؜Ӟȶң ߝɁۭߝײݮ࠵ऀ ǦǮ ՜ؼΌৃҟdžځވࣺȶң ܯ߆ढޭ֚ޭݮߵҤԦߵߣ ǸȗܤؖԷҟ০ԦߥdžȶңײݮՌ ߵӞυȶңҢҟ࠭ࢯȶң Ӊ਼ࣞޭ̻֡ȶңPart NO. N026579