Hilti SID/SIW 14-A/18-A Changing insert tools with the SIW 14-A and SIW 18-A, Fitting the socket

Page 17

en

7.1.2Changing insert tools with the SIW 14-A and SIW 18-A 4

NOTE

The power tool is equipped with two different chucks: {/" square drive with ball-notch retention or u/" with locking ring

7.1.2.1Fitting the socket

1.Set the forward / reverse switch to the middle position or remove the battery from the power tool.

2.Align the hole in the side of the socket with the retention ball on the square drive.

3.Push the socket onto the square drive until it engages.

7.1.2.2Removing the socket

1.Set the forward / reverse switch to the middle position or remove the battery from the power tool.

2.Through the round hole in the side of the socket, press the retention ball into the square drive.

3.Pull the socket off the square drive.

7.2Setting forward or reverse rotation 5

NOTE

The forward / reverse switch is used to select the direction of rotation of the drive spindle. An interlock prevents switching while the motor is running. The control switch is locked when the forward / reverse switch is in the middle position. Push the forward / reverse switch to the right (as seen in the working direction) for forward rotation. Push the forward / reverse switch to the left (as seen in the working direction) for reverse rotation.

NOTE

The power tool’s working light is no substitute for good general illumination of the working area.

7.3 Torque selector switch 6

The torque selector switch can be used to set the torque to one of three settings (see Technical Data section).

Slide the switch to the desired torque setting.

7.4 Switching on / off

The speed of the power tool can be controlled smoothly (increased from minimum to maximum) by pressing the control switch gradually.

7.5 Driving screws and tightening bolts

7.5.1Fitting the bit / bit holder

1.Set the forward / reverse switch to the middle position or remove the battery from the power tool.

2.Fit the appropriate insert tool in the chuck.

7.5.2Screwdriving

WARNING

Ensure fastener and attachment will withstand the level of torque generated by the tool. Excessive torque may overstress, strip or damage the fas- tener/attachment and possibly lead to personal injury.

1.Set the forward / reverse switch to the desired direction of rotation.

2.Set the torque selector switch to the desired torque.

7.6Reading the charge status LED display on Liion batteries 7

NOTE

The charge status cannot be indicated while the power tool is in operation. Indication is given (LED 1 blinks) only when the battery is fully discharged or when it is too hot (temperature above 80°C).

The Li-ion battery features a charge status LED dis- play. The charge status is indicated by the LEDs on the battery during charging (please refer to the section “Li-ion battery charge status”). When the battery is at rest (not in use), its charge status is indicated by the four LEDs on the battery for a time of three seconds after pressing one of the battery release buttons.

7.7 Belt hook 8

CAUTION

Check that the belt hook is fitted securely before beginning work.

The belt hook allows the power tool to be attached to a belt worn by the operator. The belt hook can also be fitted to the other side of the power tool for use by left-handed persons.

1.Pull the battery out of the tool.

2.Fit the mounting plate into the guides provided.

3.Secure the belt hook with the two screws.

10

Image 17
Contents SID/SIW   $K   $K   $K   $K   $K Page Page Stop Volt Li-Ion Page Safety notices and their meaning ContentsGeneral information Operating controls and partsDescription SymbolsObligation signs Use of the product as directedInsert tools, accessories Power tool Position Technical dataPower tool SID 14ತA SIW 14ತA SID 18ತA SIW 18ತA General power tool safety warnings Safety instructionsBattery 14/1.6 14/3.3 18/1.6 18/2.6 18/3.3 Battery tool use and care Personal safetyPower tool use and care Children must be instructed not to play with the power tool ServiceAdditional safety precautions Personal safety Charging a previously used battery Battery use and careBefore use Work area Ensure that the workplace is well litOperation Torque selector switch Setting forward or reverse rotationSwitching on / off Changing insert tools with the SIW 14-A and SIW 18-ACare of the power tool Care and maintenanceCare of the Li-ion battery Checking the power tool after care and maintenanceDisposal TroubleshootingFault Possible cause Remedy Manufacturer’s warranty tools 2012668