Panasonic SC-HT740, SC-HT940 Attaching to Wall, Fitting speaker stands not included, Assembling

	8582En		_p03-attachment13.fmPage6may resultMonday,in damageMarch27,to the20063:59PMwall and speakers.
			Speaker installation options
		∫ Attaching to		wall
Setup			You can att ch all of the speakers (except subwoofer) to a wall.
			≥ The wall or pillar on which the speakers are to be attached should be
			capable of supporti	g over 10 kg (22 lbs) [[HT940] 15 kg (33 lbs)
			for the front speakers] per sc ew. Consult a qualified building
Simple			contractor when attaching the speakers to a wall. Improper
			≥ When mounting the front speakers to a wall, we recommend using
			a string (not included) to prevent it from falling.
			2 Screws [HT740] [HT743]		2 Cover plates [HT740] [HT743]

Preparation for front speakers [HT740] [HT743]

1 Remove the speaker cable from the stand.

speakersfrontthe	Release the cable
	from the groove.
Assembling	2 Connect the cable (➜ page 4).
	[HT940]
	1 Pull down the longer part
	of the cable to release
	the cable from the groove
	inside the stand, and
	then pull the speaker cable out from the stand.

2 Feed the cable into the bottom of the speaker and through the slot at the rear.

3 Connect the cable (➜ page 5).

1 [HT740] [HT743] Attach the cover plate to the front speaker.

Cover plate Screw

Tighten securely.

2Drive a screw (not included) into the wall.

		‰7.5 to 9.5 mm
‰4.0 mm (5/32q)
		(19/64q to 3/8q)
Wall or pillar
	5.0 to 7.0 mm (3/16q to 9/32q)

3Fit the speaker securely onto the screw(s) with the hole(s).

Front speaker [HT740] [HT743] Center speaker [HT740] [HT743]

106 mm
(43/16z)
	200 mm
	(77/8z)
340 mm
(133/8z)	Surround speaker [HT740] [HT743]
RQT8582

6

Front speaker [HT940] Center speaker [HT940]

255 mm		190 mm
(101/16z)
		(715/32z)
		Surround speaker [HT940]
	320 mm
	(1219/32z)
e.g.	In this position, the	Move the speaker
	speaker will likely	so that the screw
	fall if moved to the	is in this position.
	left or right.

Reattaching the speaker cable to the stand [HT740] [HT743]

1	Remove the eight screws	Screw
	from the stand, and remove
	the speaker net.
2	Position the cable.

Press the cable into the groove.

Approx.

15 cm Cable (529/32z)

3 Attach the speaker net with the screws.

[HT940]

1 Remove the two screws from the stand, and remove the metal cover.

Screw Screw

Metal cover

Plastic cover

2Pull the cable out about 40 cm (153/4z) from the hole in the metal cover, and insert the plastic cover.

Approx. 40 cm (153/4z)

3 Insert the metal cover so it does not disturb the cable and close tightly with the two screws.

∫Fitting speaker stands (not included)

(Except front speakers)

Ensure the stands meet these conditions before purchasing them. Note the diameter and length of the screws and the distance between screws as shown in the diagram.

≥The stands must be able to support over 10 kg (22 lbs).

≥The stands must be stable even if the speakers are in a high position.

e.g. Center speaker [HT740] [HT743]

Metal screw holes

For attaching to speaker stands

5 mm (3/16q), pitch 0.8 mm (1/32q)

Plate thickness plus 7 mm
to 10 mm (plus 9/32q to 13/32q)	60 mm (23/8q)

Speaker stand (not included)