HP XC System 3.x Software manual Tuning Applications

Page 59

7 Tuning Applications

This chapter discusses how to tune applications in the HP XC environment.

Using the Intel Trace Collector and Intel Trace Analyzer

This section describes how to use the Intel Trace Collector (ITC) and Intel Trace Analyzer (ITA) with HP-MPI on an HP XC system. The Intel Trace Collector/Analyzer were formerly known as VampirTrace and Vampir, respectively. This section addresses the following topics:

•Building a Program — Intel Trace Collector and HP-MPI (page 59)

•Running a Program – Intel Trace Collector and HP-MPI (page 60)

•Visualizing Data – Intel Trace Analyzer and HP-MPI (page 60)

The following Intel Trace Collector/Analyzer documentation is available on the HP XC system after Intel Trace Collector/Analyzer is installed:

•Intel Trace Collector Users Guide — located on the HP XC system at:

<install-path-name>/ITC/doc/Intel_Trace_Collector_Users_Guide.pdf.

•Intel Trace Analyzer Users Guide — located on the HP XC system at:

<install-path-name>/ITA/doc/Intel_Trace_Analyzer_Users_Guide.pdf

Building a Program — Intel Trace Collector and HP-MPI

HP-MPI is MPICH compatible if you use the HP-MPI MPICH scripts which are located at: /opt/hpmpi/bin. The HP-MPI MPICH scripts are:

•mpicc is replaced by mpicc.mpich

•mpif77 is replaced by mpif77.mpich

•mpirun is replaced by mpirun.mpich

In summary, mpixx becomes mpixx.mpich.

For further information, refer to the Intel Trace Collector Users Guide. This document is located on the HP XC system at the following location:

<install-path-name>/ITC/doc/Intel_Trace_Collector_Users_Guide.pdf.

Using the Intel Trace Collector and Intel Trace Analyzer 59

Image 59

Contents HP XC System Software Users Guide Page Table of Contents Submitting Jobs Configuring Your Environment with ModulefilesDeveloping Applications Debugging Applications Tuning ApplicationsUsing Slurm Using LSFGlossary 109 Index 115 Advanced TopicsExamples List of Figures Page Determining the Node Platform List of TablesPage Submitting a Job Script List of ExamplesPage This document is organized as follows About This DocumentIntended Audience Document OrganizationHP XC Information Supplementary Information $ man lsfcommandnameFor More Information $ man -k keyword Related InformationManpages $ man discover $ man 8 discoverAdditional Publications Related Linux Web SitesRelated MPI Web Sites Related Compiler Web SitesUser input Typographic ConventionsHP Encourages Your Comments Environment VariableOperating System Overview of the User EnvironmentSystem Architecture HP XC System SoftwareStorage and I/O Node SpecializationFile System Layout File SystemSAN Storage Local StorageNetwork Address Translation NAT Determining System Configuration InformationSystem Interconnect Network Modules CommandsUser Environment Serial Applications Application Development EnvironmentRun-Time Environment Parallel ApplicationsHow LSF-HPC and Slurm Interact Load Sharing Facility LSF-HPCStandard LSF Components, Tools, Compilers, Libraries, and Debuggers Mpirun commandLogging In to the System Using the SystemLVS Login Routing Using the Secure Shell to LogGetting Information About Resources IntroductionGetting Information About Queues Performing Other Common User Tasks $ man sinfo Getting System Help and InformationOverview of Modules Configuring Your Environment with ModulefilesSupplied Modulefiles Loading a Modulefile Modulefiles Automatically Loaded on the SystemViewing Available Modulefiles Viewing Loaded ModulefilesLoading a Modulefile for the Current Session Automatically Loading a Modulefile at LoginUnloading a Modulefile Modulefile Conflicts$ module help totalview Creating a ModulefileViewing Modulefile-Specific Help $ module load modules $ man modulefilePage Compilers Developing ApplicationsApplication Development Environment Overview Partition Avail Timelimit Nodes State Nodelist Examining Nodes and Partitions Before Running JobsInterrupting a Job MPI CompilerBuilding Serial Applications Setting Debugging OptionsDeveloping Serial Applications Serial Application Build EnvironmentOpenMP Developing Parallel ApplicationsParallel Application Build Environment ModulefilesIntel Fortran and C/C++Compilers PthreadsQuadrics Shmem MPI LibraryBuilding Parallel Applications Examples of Compiling and Linking HP-MPI Applications Developing LibrariesDesigning Libraries for the CP4000 Platform To build a 64-bit application, you might enter Linkcommand 32-bit -L/opt/mypackage/lib/i686 -lmystuffLinkcommand 64-bit -L/opt/mypackage/lib/x8664 -lmystuff ExtSLURMslurm-arguments Submitting JobsOverview of Job Submission $ bsub hostname Submitting a Serial Job Using Standard LSFSubmitting a Serial Job Using LSF-HPC Submitting a Serial Job with the LSF bsub CommandSubmitting a Serial Job Through Slurm only Mpirun mpirun--options-srunsrun-optionsmpi-jobname Submitting a Non-MPI Parallel Job$ bsub -n4 -I srun hostname Bsub -nnum-procsbsub-optionsmpijobBsub -nnum-procs bsub-optionsscript-name Submitting a Batch Job or Job Script$ bsub -n4 -I mpirun -srun ./helloworld $ bsub -n4 -ext SLURMnodes=4 -I ./myscript.sh $ cat myscript.sh #!/bin/shSrun hostname mpirun -srun hellompi $ bsub -I -n4 Myscript.sh$ cat ./envscript.sh #!/bin/sh name=`hostname` Running Preexecution Programs$ bsub -n4 -I ./myscript.sh Opt/hptc/bin/srun Mypreexec TotalView Debugging ApplicationsDebugging Serial Applications Debugging Parallel ApplicationsModule load mpimodule load totalview Setting Up TotalViewUsing TotalView with Slurm SSH and TotalViewDebugging an Application Using TotalView with LSF-HPCSetting TotalView Preferences $ mpirun -srun -n2 Psimple Sourcefile initfdte.f was not found, using assembler modeDebugging Running Applications Directories in File ⇒ Search Path$ squeue $ scancel --user usernameExiting TotalView Page Building a Program Intel Trace Collector and HP-MPI Tuning ApplicationsUsing the Intel Trace Collector and Intel Trace Analyzer Cldflags Running a Program Intel Trace Collector and HP-MPIVisualizing Data Intel Trace Analyzer and HP-MPI LibsUsing the Intel Trace Collector and Intel Trace Analyzer Page Introduction to Slurm Using SlurmLaunching Jobs with the srun Command Srun Squeue Scancel Sinfo ScontrolSrun Roles and Modes Monitoring Jobs with the squeue CommandUsing the srun Command with HP-MPI Using the srun Command with LSF-HPCJob Accounting Terminating Jobs with the scancel CommandGetting System Information with the sinfo Command # chmod a+r /hptccluster/slurm/job/jobacct.log Fault ToleranceSecurity Using LSF-HPC Using LSFUsing Standard LSF on an HP XC System Overview of LSF-HPC Introduction to LSF-HPC in the HP XC EnvironmentHostname Status JL/U MAX Njobs RUN Ssusp Ususp RSV Differences Between LSF-HPC and Standard LSFHostname ResourcesUnknown Unknown Job Terminology$ ssh n15 lshosts SLURMnodelist =nodelist if specified HP XCCompute Node Resource Support$ bsub -n 10 -ext SLURMconstraint=dualcore -I srun hostname $ bsub -n 10 -I srun hostname$ bsub -n 10 -ext SLURMnodes=10 -I srun hostname $ bsub -n 10 -ext SLURMnodes=10exclude=n16 -I srun hostname$ bsub -n4 -ext SLURMnodes=4 -o output.out ./myscript How LSF-HPC and Slurm Launch and Manage a Job#!/bin/sh hostname srun hostname Mpirun -srun ./hellompi Job Startup and Job ControlGetting Information About LSF Execution Host Node Determining the LSF Execution HostDetermining Available LSF-HPC System Resources Getting the Status of LSF-HPCSLINUX6 Getting Host Load InformationExamining LSF-HPC System Queues Getting Information About the lsf Partition$ sinfo -p lsf -lNe Summary of the LSF bsub Command Format$ sinfo -p lsf Bsub-options srun srun-optionsjobname job-options LSF-SLURM External SchedulerFor information about running scripts Bsub -n num-procs-ext SLURMslurm-arguments \Type=SLINUX64 Submitting a Job from a Non-HP XC HostStarting on lsfhost.localdomain n6 Waiting for dispatch ... Starting on lsfhost.localdomain n1$ bjobs -l Getting Information About JobsGetting Job Allocation Information Slurmid=slurmjobidncpus=slurmnprocsslurmalloc=nodelist$ bjobs Examining the Status of a Job$ bhist -l Time stampJobid User Jobname Pend Psusp RUN Ususp Ssusp Unkwn Total Viewing the Historical Information for a Job$ bhist Summary of time in seconds spent Various StatesTranslating Slurm and LSF-HPC JOBIDs $ srun --jobid=150 hostname Working Interactively Within an LSF-HPC Allocation$ bsub -I -n4 -ext SLURMnodes=4 /bin/bash $ bjobs -l 124 grep slurm$ unset Slurmjobid $ unset Slurmnprocs $ unset SlurmjobidAlternatively, you can use the following $ export SLURMJOBID=150 $ export SLURMNPROCS=4$ bsub -n4 -ext SLURMnodes=4 -o %J.out sleep Job 125 is submitted to the default queue normalLSF-HPC Equivalents of Slurm srun Options $ srun --jobid=250 uptimeBsub -iinputfile Mpi=mpitype Quit-on-interrupt Page Determining IP Address of Your Local Machine Advanced TopicsEnabling Remote Execution with OpenSSH Running an X Terminal Session from a Remote NodeLogging in to HP XC System Running an X terminal Session Using SlurmRunning an X terminal Session Using LSF-HPC $ srun -n2 hostname n46 Using the GNU Parallel Make Capability$ bsub -n4 -Ip srun -n1 xterm -display $ srun -n4 hostname n46$ cd subdir srun -n1 -N1 $MAKE -j4 $ make PREFIX=’srun -n1 -N1 MAKEJ=-j4 Example Procedure$ make PREFIX=srun -n1 -N1 MAKEJ=-j4 Local Disks on Compute NodesPerformance Considerations Modified Makefile is invoked as followsFp = fopen myfile, a+ Communication Between NodesShared File View Private File ViewPage Examine the LSF execution host information Appendix a ExamplesBuilding and Running a Serial Application Launching a Serial Interactive Shell Through LSF-HPCRunning LSF-HPC Jobs with a Slurm Allocation Request SLURMnodes=2 Launching a Parallel Interactive Shell Through LSF-HPCExample 2. Four cores on Two Specific Nodes R15s r1m r15m It tmp swp mem LoadSched LoadStop124 Lsfad Examine the the running jobs information$ hostname n16 $ srun hostname n5 $ bjobs Display the script Submitting a Simple Job Script with LSF-HPCExamine the the finished jobs information Show the environmentShow the job allocation Run some commands from the pseudo-terminalSubmitting an Interactive Job with LSF-HPC Submit the jobView the finished jobs Submitting an HP-MPI Job with LSF-HPCExit the pseudo-terminal View the interactive jobsLsfhost.localdomai View the running jobView the finished job $ bsub -n 8 -R ALPHA5 SLINUX64 \ -ext SLURMnodes=4-4 myjob Using a Resource Requirements String in an LSF-HPC CommandStates by date and time 108 Glossary Are not appropriate for replication To the queueFirst-come See Fcfs First-served Global storage As local storageLSF master host Single commandLogin requests and directs them to a node with a login role Linux Virtual See LVS Server Load fileSlurm backup Network See NIS Information ServicesRemotely. PXE booting is configured at the Bios level Notably to install and remove software packagesSymmetric See SMP Multiprocessing Power available per unit of spaceSsh 114 Index Index PGI Utilities, 63 Slurm commands