HP VCX Software Interface Network Interface 1, Telecommuting Module Type configuration, General

Page 27

Chapter 4. Network Configuration

The Telecommuting Module derives information about your network topology from the in- terface configuration.

Telecommuting Module Type configuration

Current Telecommuting Module Type

Shows which type is currently active.

Change Telecommuting Module Type to

Select a new Telecommuting Module Type here.

Change type

Press the Change type button to set the new Telecommuting Module Type. This setting, like others, must be applied on the Save/Load Configuration page before it affects the Telecommuting Module functionality.

Interface (Network Interface 1 and 2)

There is a page for each network interface (Network Interface 1 and 2) on the Telecommuting Module. Select a page to make configuration for that interface. There is also a page where configuration for all interfaces can be viewed and changed.

Here, you set the interface name, whether the interface is on or off, the IP address, alias, and static routing.

For each interface, go to Directly Connected Networks and state the IP address of the Telecommuting Module and the size of the network connected to this interface.

General

19

Image 27
Contents Getting started Guide 3Com VCX IP Telecommuting ModulePage 3Com VCX IP Telecommuting Module Getting started Guide Page Table of Contents Page Part I. Installation of the 3Com VCX IP Telecommuting Module Page DMZ Configuration What is a Telecommuting Module?Introduction Configuration alternativesStandalone Configuration DMZ/LAN ConfigurationOverview of the Installation License Conditions About settings in 3Com VCX IP Telecommuting ModuleInstallation with a serial cable Installing 3Com VCX IP Telecommuting ModuleInstallation Installation with magic pingPage Page Page Page Installation with a diskette Page Page Remember to lock up the Telecommuting Module Turning off a Telecommuting ModuleInstalling 3Com VCX IP Telecommuting Module Part II. Configuring 3Com VCX IP Telecommuting Module Page Telecommuting Module Type Network ConfigurationNetwork Configuration Interface Network Interface 1 Telecommuting Module Type configurationGeneral Interface name Directly Connected NetworksPhysical device StatusNetmask/Bits NameDNS Name Or IP Address IP addressAlias Static Routing Routed networkRouter Save Default GatewayCancel Main Default GatewaysInterface Policy For Packets From Unused GatewaysGateway Reference Hosts DynamicNetworks and Computers Name SubgroupLower Limit Create Upper LimitInterface/VLAN Delete RowAdditional Negotiators SurroundingsSurroundings NetworkData Interfaces Policy For Ping To Your 3Com VCX IP Telecommuting Module Default domain IP PolicyBasic Configuration Name of this Telecommuting ModuleDNS Servers Reverts all the above fields to their previous configuration Network Configuration SIP Module Basic SettingsAdditional SIP Signaling Ports SIP ConfigurationComment Provisioning RelaySIP Media Port Range TransportPublic IP address for NATed Telecommuting Module SIP Servers To MonitorServer Log class for SIP license messages Log class for SIP signalingSIP Logging Log class for SIP packetsLog class for SIP media messages Log class for SIP errorsRouting DNS Override For SIP RequestsRelay To DomainAction FilteringSender IP Filter Rules From NetworkContent Types Default Policy For SIP RequestsContent Type Interoperability URI EncodingAllow Remote NAT traversal Remote Clients Signaling ForwardingRemote SIP Connectivity Remote NAT TraversalNAT timeout for UDP NAT timeout for TCPNAT keepalive method Media Route Administration of the Telecommuting Module Access ControlConfiguration Allowed Via Interface Configuration Transport User Authentication For Web Interface AccessConfiguration via SSH Configuration ComputersConfiguration via Http Configuration via HttpsDNS Name Or Network Address Netmask/Bits RangeVia IPsec Peer Log Class SSHApply configuration Duration of limited test modeSave/Load Configuration Test Preliminary ConfigurationBackup Show Message About Unapplied ChangesSave to diskette Save/Load CLI Command File Revert to Old Configurations Abort All EditsReload Factory Configuration Administration of the Telecommuting Module Firewall and Client Configuration DMZ typeFirewall DMZ/LAN type SIP clientsOther Standalone type SIP clients Apply Index
Related manuals
Manual 446 pages 4.55 Kb