HP VCX Software manual

Page 17

Chapter 3. Installing 3Com VCX IP Telecommuting Module

Password []:

Finally, you are asked if you want to reset other configuration.

Other configuration

Do you want to reset the rest of the configuration? (y/n) [n]

If you answer n, nothing is removed. If you answer y, you have three alternatives to select from:

1.Clear as little as possible. This is the alternative that is used if you answer n to the question above. Both the preliminary and the permanent configurations will be updated with the configuration specified above.

2.Revert to the factory configuration and then apply the configuration specified above. This will affect the permanent but not the preliminary configuration.

3.Revert to the factory configuration and empty all logs and then apply the configuration specified above. Both the preliminary and the permanent configurations will be affected.

Select the update mode, which is what you want to remove.

Update mode (1-3) [1]:

All configuration is now complete. The installation program shows the configuration and asks if it is correct.

yes saves the configuration.

no runs the installation program over again.

abort ends the installation program without saving.

You have now entered the following configuration

Network configuration inside:

Physical device name: eth0

IP address: 192.168.150.2

Netmask: 255.255.255.0

Deactivate other interfaces: no

Computer allowed to configure from:

IP address: 192.168.128.3

Password: eeyore

The rest of the configuration is kept.

Is this configuration correct (yes/no/abort)? yes

9

Image 17
Contents Getting started Guide 3Com VCX IP Telecommuting ModulePage 3Com VCX IP Telecommuting Module Getting started Guide Page Table of Contents Page Part I. Installation of the 3Com VCX IP Telecommuting Module Page Introduction What is a Telecommuting Module?Configuration alternatives DMZ ConfigurationStandalone Configuration DMZ/LAN ConfigurationOverview of the Installation License Conditions About settings in 3Com VCX IP Telecommuting ModuleInstallation Installing 3Com VCX IP Telecommuting ModuleInstallation with magic ping Installation with a serial cablePage Page Page Page Installation with a diskette Page Page Remember to lock up the Telecommuting Module Turning off a Telecommuting ModuleInstalling 3Com VCX IP Telecommuting Module Part II. Configuring 3Com VCX IP Telecommuting Module Page Telecommuting Module Type Network ConfigurationNetwork Configuration General Interface Network Interface 1Telecommuting Module Type configuration Physical device Directly Connected NetworksStatus Interface nameDNS Name Or IP Address NameIP address Netmask/BitsAlias Router Static RoutingRouted network Cancel Default GatewayMain Default Gateways SaveGateway Reference Hosts Policy For Packets From Unused GatewaysDynamic InterfaceNetworks and Computers Lower Limit NameSubgroup Interface/VLAN Upper LimitDelete Row CreateSurroundings SurroundingsNetwork Additional NegotiatorsData Interfaces Basic Configuration Default domain IP PolicyName of this Telecommuting Module Policy For Ping To Your 3Com VCX IP Telecommuting ModuleDNS Servers Reverts all the above fields to their previous configuration Network Configuration Additional SIP Signaling Ports Basic SettingsSIP Configuration SIP ModuleSIP Media Port Range Provisioning RelayTransport CommentServer Public IP address for NATed Telecommuting ModuleSIP Servers To Monitor SIP Logging Log class for SIP signalingLog class for SIP packets Log class for SIP license messagesRouting Log class for SIP errorsDNS Override For SIP Requests Log class for SIP media messagesRelay To DomainSender IP Filter Rules FilteringFrom Network ActionContent Type Content TypesDefault Policy For SIP Requests Allow InteroperabilityURI Encoding Remote SIP Connectivity Remote Clients Signaling ForwardingRemote NAT Traversal Remote NAT traversalNAT keepalive method NAT timeout for UDPNAT timeout for TCP Media Route Configuration Allowed Via Interface Administration of the Telecommuting ModuleAccess Control Configuration Transport User Authentication For Web Interface AccessConfiguration via Http Configuration ComputersConfiguration via Https Configuration via SSHVia IPsec Peer DNS Name Or Network AddressNetmask/Bits Range Log Class SSHSave/Load Configuration Duration of limited test modeTest Preliminary Configuration Apply configurationSave to diskette BackupShow Message About Unapplied Changes Save/Load CLI Command File Reload Factory Configuration Revert to Old ConfigurationsAbort All Edits Administration of the Telecommuting Module Firewall Firewall and Client ConfigurationDMZ type Other DMZ/LAN typeSIP clients Standalone type SIP clients Apply Index
Related manuals
Manual 446 pages 4.55 Kb