HP 210 manual Removing Battery

Page 78

C a u t i o n

W A R N I N G

Troubleshooting

Replacing the Battery

8.Using your fingers (or a nonmetallic tool), carefully lift up the battery clip slightly, then slide the battery out of its holder.

Figure 4-1. Removing Battery

Replace the battery only with the same type.

9.Carefully insert the new battery—positive (+) side up—into the battery holder.

10.Reassemble the the router module with the SNMP module, then rein- stall them in the hub, as described in steps 6 – 12 on pages 1-13 – 1-15.

Dispose of the used battery properly. Do not attempt to recharge, crush, or disassemble it; do not incinerate it or expose it to heat above 100°C (212°F).

4-16

Page 77 Page 79
Image 78
Page 77 Page 79
Contents HP AdvanceStack Router Module Installation Guide Applicable Product About This Manual HP AdvanceStack Router 210 Module An OverviewRouter module includes two ports Page Contents Operation SmartBoot Regulatory Statements Index Installation Installation Summary Install the Router ModuleVerify the Router Module Starts Up Properly Items Included With the Router Module Other HardwareSoftware Check the Version of the Snmp Module Looking at the Snmp ModuleChecking Snmp Module Using HP Stack Manager Prepare the Network Smds individual addressPrepare the Network Install the Router Module To install the router module Connecting Grounding Wrist StrapShort out while being shipped Snmp module back until it slides out of the Expansion SlotPositioning Snmp Module Over Router Module It against the edges of the Expansion Slot Position the assembled router and Snmp modules in backHub’s Expansion Slot as shown below Firmly engage its mating connector within the Expansion Slot Align the edges of the Snmp module in the small slots nearWAN port connector Hub, connect them now refer to the hub’s installation guidePins on the router module or on the cable Connect the WAN CableInstallation Connect a Console Optional Drive and directory where the earlier version was installed MenuVerify That the Router Starts Up Properly To verify the router-module startup 12. Self-Test LEDT e Hub in the Device Chain List Down the Shift key while you click on the Access buttonDo either of the following Router, click on the Router icon buttonSetup Setup Summary Using the Main Menu and NCL Main MenuDefault NCL Prompt Create or Modify a Router Configuration SetupUsing Quick Configuration Router, use the NCL Boot command Using the Configuration EditorRouter module to activate the new configuration. To reboot TionWhere Mm = month Hh = hour Dd = day Set the Date and TimeTo set the date and time Specify Manager and User Passwords Optional Verify the Network Links Examine the Event Log EnterEvent Log Line in the Main Menu Examine the Statistics Screens Example of the Statistics Screen MenuVerify the Network Links Setup Examine the Bridging and Routing Tables Setup Test Node Accessibility PingOperation LEDs and Buttons Status LEDsStatus LEDs are located on the router module’s cover plate Operation LEDReset and Clear Buttons Reset and Clear ButtonsResetting and Clearing Resetting the Router ModuleClearing the Passwords Refer to , TroubleshootingClearing the Router Module U t i o n T e To clear the router moduleButton within five seconds after releasing the Reset button Is connected, the router module reboots using the SmartBootConfiguration Initialization Sequence Operation Troubleshooting Basic Troubleshooting Tips Interpreting LED Error Patterns LEDs on Router Module’s Cover Plate Main menu Verifying LED Operation Troubleshooting a Failure During Power-On or Reset Self-Test Router Self-Test LED On, Fault LED OnRouter Self-Test LED On, Fault LED Off Diagnostic Tests Testing the Router ModuleTesting the Router Module’s WAN Port Checking the ConfigurationTesting a Link Tests from Other DevicesPing Ping x.x.x.x count Ping x.x.x.x count waitAppleTalk Ping Telnet TelnetReplacing the Battery To replace the batteryDisconnect the hub from the power source Removing Battery Cables and Connectors Cables and Connectors Cables and a Connectors HP CablesCable and Connector Pin-Outs WAN Cable-Minimum Pin-OutsRS-232/V.24/V.28 WAN Cable-Minimum Pin-Outs WAN port is 15 meters 50 feetWAN link end RS-449/RS-422/V.36 WAN Cable-Minimum Pin-Outs Pin male CircuitBack-to-Back Test Cable Must have it set to InternalFeet RDB, and so on must be twisted pairs of wire Back-to-Back Test Cable-Minimum Pin-OutsLoopback Connector Specifications Electromagnetic Emissions Power ConsumptionEnvironmental WattsData Communications Specifications and Certifications SpecificationsThird-Party Products SmartBoot SmartBoot SmartBoot C-2 When this message appears, reconnect the network linkAbout SmartBoot Helper, refer to the Release Notes Adjacent networksVcci Class 1 Japan Only European Community Regulatory StatementsDeclaration of Conformity Index IndexIndex-1 See time MAC address See station address management of routers Index-3See WAN power 11 4-12 point to pointUser password .. -9, 3-7 See also password Time .. -8Index-5 WAN 5963-2632
Related manuals
Manual 101 pages 42.82 Kb Manual 96 pages 36.64 Kb

210 specifications

The HP 210 is a model that reflects HP's commitment to providing high-performance computing devices for a variety of professional and personal needs. Designed with modern users in mind, the HP 210 showcases a combination of sleek design, powerful features, and cutting-edge technology.

One of the standout features of the HP 210 is its robust processing capabilities. Utilizing the latest generation of Intel or AMD processors, this device ensures users can handle demanding tasks with ease, whether running complex software applications, multitasking, or engaging in content creation. The high clock speeds combined with multiple cores significantly enhance performance, making it suitable for both work and play.

In terms of memory, the HP 210 offers a flexible configuration, allowing users to choose between different RAM options. With support for both DDR4 and LPDDR4x memory, the device ensures smooth operation and efficient multitasking. This is particularly beneficial for professionals who need to run multiple applications simultaneously without experiencing lags or slowdowns.

The storage options on the HP 210 are equally impressive. Users can select from various SSD configurations, offering faster boot times, quicker application launches, and improved overall system responsiveness compared to traditional hard drives. The use of NVMe technology further amplifies these benefits by providing blazing-fast data transfer speeds.

The HP 210 features a vibrant display with high-resolution options, delivering crisp visuals that enhance the viewing experience. Whether for professional presentations, watching videos, or gaming, the display ensures that colors are rendered accurately and details are sharp.

Connectivity is another critical aspect, and the HP 210 does not disappoint. Equipped with multiple USB ports, HDMI outputs, and support for the latest Wi-Fi and Bluetooth standards, users can easily connect to various devices, peripherals, and networks. This ensures seamless integration into any workspace or home environment.

In addition to its hardware capabilities, the HP 210 prioritizes security and user privacy. With features such as a fingerprint reader and advanced encryption technologies, users can have peace of mind knowing that their sensitive data is protected.

Overall, the HP 210 is designed for users who demand both performance and versatility. With its powerful processor options, ample memory and storage, stunning display, and robust connectivity features, it is an excellent choice for professionals, students, and everyday users alike, making it a well-rounded addition to HP's lineup of innovative computing solutions.
Top Page Image Contents