HP 210 Replacing the Battery, To replace the battery, Disconnect the hub from the power source

Page 77

C a u t i o n

Troubleshooting

Replacing the Battery

Replacing the Battery

If you have made changes to the factory-default configuration but that factory-default configuration is restored when you boot the router, the battery may need to be replaced.

To replace the battery:

1.Disconnect the hub from the power source,

2.Using the supplied nutdriver, remove the two hex nut screws along- side the WAN port connector. (See figure 1-10 on page 1-15.)

3.Using a Torx T-10 or flat-blade screwdriver, loosen the two captured screws holding the cover plate over the hub’s Expansion Slot, then remove the cover plate. (See figure 1-3 on page 1-11.)

4.Connect a grounding wrist strap between your wrist and the hub. (Refer to step 2 on page 1-11.)

Static electricity can severely damage sensitive electronic components such as the router module or the SNMP module.

5.Remove the router and SNMP modules from the hub. (Refer to step 5 on page 1-12.) Place the modules, with the router module on the bottom, on a nonconducting antistatic surface.

6.Using a Phillips (cross-head) screwdriver, remove the four screws securing the SNMP module to the standoffs. (See figure 1-8 on page 1-14.)

7.Carefully disengage the connectors holding the two modules together, then place the SNMP module on an antistatic surface.

Troubleshooting 4

4-15

Page 76 Page 78
Image 77
Page 76 Page 78
Contents HP AdvanceStack Router Module Installation Guide Applicable Product About This Manual An Overview HP AdvanceStack Router 210 ModuleRouter module includes two ports Page Contents Operation SmartBoot Regulatory Statements Index Installation Install the Router Module Installation SummaryVerify the Router Module Starts Up Properly Software Items Included With the Router ModuleOther Hardware Looking at the Snmp Module Check the Version of the Snmp ModuleChecking Snmp Module Using HP Stack Manager Smds individual address Prepare the NetworkPrepare the Network Install the Router Module Connecting Grounding Wrist Strap To install the router moduleSnmp module back until it slides out of the Expansion Slot Short out while being shippedPositioning Snmp Module Over Router Module Hub’s Expansion Slot as shown below It against the edges of the Expansion SlotPosition the assembled router and Snmp modules in back Align the edges of the Snmp module in the small slots near Firmly engage its mating connector within the Expansion SlotPins on the router module or on the cable Hub, connect them now refer to the hub’s installation guideWAN port connector Connect the WAN CableInstallation Connect a Console Optional Menu Drive and directory where the earlier version was installedVerify That the Router Starts Up Properly 12. Self-Test LED To verify the router-module startupT e Do either of the following Down the Shift key while you click on the Access buttonHub in the Device Chain List Router, click on the Router icon buttonSetup Setup Summary Main Menu Using the Main Menu and NCLDefault NCL Prompt Setup Create or Modify a Router ConfigurationUsing Quick Configuration Router module to activate the new configuration. To reboot Using the Configuration EditorRouter, use the NCL Boot command TionTo set the date and time Where Mm = month Hh = hour Dd = daySet the Date and Time Specify Manager and User Passwords Optional Verify the Network Links Enter Examine the Event LogEvent Log Line in the Main Menu Example of the Statistics Screen Menu Examine the Statistics ScreensVerify the Network Links Setup Examine the Bridging and Routing Tables Setup Ping Test Node AccessibilityOperation Status LEDs are located on the router module’s cover plate LEDs and ButtonsStatus LEDs LED OperationReset and Clear Buttons Reset and Clear ButtonsResetting the Router Module Resetting and ClearingRefer to , Troubleshooting Clearing the PasswordsClearing the Router Module To clear the router module U t i o n T eConfiguration Button within five seconds after releasing the Reset buttonIs connected, the router module reboots using the SmartBoot Initialization Sequence Operation Troubleshooting Basic Troubleshooting Tips Interpreting LED Error Patterns LEDs on Router Module’s Cover Plate Main menu Verifying LED Operation Router Self-Test LED On, Fault LED On Troubleshooting a Failure During Power-On or Reset Self-TestRouter Self-Test LED On, Fault LED Off Testing the Router Module Diagnostic TestsChecking the Configuration Testing the Router Module’s WAN PortTests from Other Devices Testing a LinkPing x.x.x.x count Ping x.x.x.x count wait PingAppleTalk Ping Telnet TelnetDisconnect the hub from the power source Replacing the BatteryTo replace the battery Removing Battery Cables and Connectors Cables and Connectors HP Cables Cables and a ConnectorsWAN Cable-Minimum Pin-Outs Cable and Connector Pin-OutsWAN port is 15 meters 50 feet RS-232/V.24/V.28 WAN Cable-Minimum Pin-OutsWAN link end Pin male Circuit RS-449/RS-422/V.36 WAN Cable-Minimum Pin-OutsFeet Back-to-Back Test CableMust have it set to Internal Back-to-Back Test Cable-Minimum Pin-Outs RDB, and so on must be twisted pairs of wireLoopback Connector Specifications Environmental Power ConsumptionElectromagnetic Emissions WattsThird-Party Products Data Communications Specifications and CertificationsSpecifications SmartBoot SmartBoot SmartBoot About SmartBoot Helper, refer to the Release Notes When this message appears, reconnect the network linkC-2 Adjacent networksRegulatory Statements Vcci Class 1 Japan Only European CommunityDeclaration of Conformity Index-1 IndexIndex See time Index-3 MAC address See station address management of routers11 4-12 point to point See WAN powerIndex-5 User password .. -9, 3-7 See also passwordTime .. -8 WAN 5963-2632
Related manuals
Manual 101 pages 42.82 Kb Manual 96 pages 36.64 Kb

210 specifications

The HP 210 is a model that reflects HP's commitment to providing high-performance computing devices for a variety of professional and personal needs. Designed with modern users in mind, the HP 210 showcases a combination of sleek design, powerful features, and cutting-edge technology.

One of the standout features of the HP 210 is its robust processing capabilities. Utilizing the latest generation of Intel or AMD processors, this device ensures users can handle demanding tasks with ease, whether running complex software applications, multitasking, or engaging in content creation. The high clock speeds combined with multiple cores significantly enhance performance, making it suitable for both work and play.

In terms of memory, the HP 210 offers a flexible configuration, allowing users to choose between different RAM options. With support for both DDR4 and LPDDR4x memory, the device ensures smooth operation and efficient multitasking. This is particularly beneficial for professionals who need to run multiple applications simultaneously without experiencing lags or slowdowns.

The storage options on the HP 210 are equally impressive. Users can select from various SSD configurations, offering faster boot times, quicker application launches, and improved overall system responsiveness compared to traditional hard drives. The use of NVMe technology further amplifies these benefits by providing blazing-fast data transfer speeds.

The HP 210 features a vibrant display with high-resolution options, delivering crisp visuals that enhance the viewing experience. Whether for professional presentations, watching videos, or gaming, the display ensures that colors are rendered accurately and details are sharp.

Connectivity is another critical aspect, and the HP 210 does not disappoint. Equipped with multiple USB ports, HDMI outputs, and support for the latest Wi-Fi and Bluetooth standards, users can easily connect to various devices, peripherals, and networks. This ensures seamless integration into any workspace or home environment.

In addition to its hardware capabilities, the HP 210 prioritizes security and user privacy. With features such as a fingerprint reader and advanced encryption technologies, users can have peace of mind knowing that their sensitive data is protected.

Overall, the HP 210 is designed for users who demand both performance and versatility. With its powerful processor options, ample memory and storage, stunning display, and robust connectivity features, it is an excellent choice for professionals, students, and everyday users alike, making it a well-rounded addition to HP's lineup of innovative computing solutions.
Top Page Image Contents