Sterling 882.00295.00 specifications Reporting a Safety Defect

Page 11

When you need to perform maintenance or repair work on a dehumidifying dryer above floor level, use a solid platform or a hydraulic elevator. If there is a permanently installed catwalk on your dryer, use it. The work platform should have secure footing and a place for tools and parts. DO NOT climb on the dehumidifying dryer, machines, or work from ladders.

If you need to repair a large component, use appropriate handling equipment. Before you use handling equipment (portable “A” frames, electric boom trucks, fork trucks, overhead cranes) be sure the load does not exceed the capacity of the handling equipment or cause it to become unstable.

Carefully test the condition of lifting cables, chains, ropes, slings, and hooks before using them to lift a load.

Be sure that all non-current carrying parts are correctly connected to earth ground with an electrical conductor that complies with current codes. Install in accordance with national and local codes.

When you have completed the repair or maintenance procedure, check your work and remove your tools, rigging, and handling equipment.

Do not restore power to the dehumidifying dryer until all persons are clear of the area. DO NOT start and run the dryer until you are sure all parts are functioning correctly.

BEFORE you turn the dehumidifying dryer over to the operator for production, verify all enclosure panels, guards and safety devices are in place and functioning properly.

Reporting a Safety Defect

If you believe that your equipment has a defect that could cause injury, you should immediately discontinue its use and inform the manufacturer.

The principle factors that can result in injury are failure to follow proper operating procedures (i.e. lockout/tagout), or failure to maintain a clean and safe working environment.

Large Dehumidifying Dryers

Safety

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents SDA 1000-5100 Series Large Dehumidifying Dryer AP-1 Control If the Shipment is Not Complete Shipping InfoUnpacking and Inspection Event of Shipping DamageCredit Returns ReturnsTable of Contents Operation Large Dehumidifying Dryers Safety Symbols Used in this Manual SafetyHow to Use This Manual Dryer Safety Tags Description Operator Responsibility ResponsibilityGeneral Responsibility Maintenance Responsibility Reporting a Safety Defect General Description Functional DescriptionModels Covered in This Manual Sequence of Operation Process/Regeneration CycleElectrical Features Standard FeaturesAuto Start Timer Mechanical FeaturesClosed-Loop Regeneration OptionsDewpoint Extend Drawings and Diagrams Optional dryer dust collector Process Air Dust Collector Aftercooler Design SpecificationsProcess Aftercooler Process Air Dust Collector Material Overdrying Protection Recommended Temperature SettingsController Options Mechanical OptionsElectrical Options Fail Safe Operation Safety Devices and InterlocksSafety Circuit Standards Safety Device Lock-OutsPage Mechanical Options Denotes availability Dimensions and Specifications Denotes availabilityDenotes availability Making Electrical Connections Mechanical InstallationUncrating the Equipment Rigging and Placing UnitDescription Making Gas Line Connections Gas-Fired Models OnlyChecking Blower Rotation Checking for Proper Blower RotationDryer/Drying Hopper Process Air Connections Making Dryer/Drying Hopper Process Air ConnectionsProcess Air Heater on Drying Hopper Large Dehumidifying Dryers Mechanical Installation Aftercooler Components & Flow Rates Connecting Aftercooler/Precooler Cooling Water OptionalDrying Hopper Air Trap Using the Drying Hopper Air TrapController Description ControlsDryer Status Screen Startup Screen Process Air Temperature and Conveying Process ControllerMain Menu Screen Dryer Alarms Help System LOG OFFIdentifying Controller Screens Setting Values Auto Start Main Menu Dryer Status Dryer Setup Over DRY Protect Alarms Auto TuneDryer Menu Dryer Setup Screen 4 Dryer Setup Screen 2Dryer Setup Screen 3 Overdry Protection Screen 2 Overdry ProtectionOverdry Protection Screen 1 Process AutoTune Screen Alarm History ScreenAutotune Auto Start DEW Point SetupDew Point Setup Screen Autostart Timer ScreenSystem Menu System Setup SET Clock Hour Meters Alarm History StatusHelp Menu Help Menu ScreenLOW Level Detection Setup System Backup Service Menu Main Menu System SetupSystem Setup Screen Autostart Clock Screen Clock Menu ScreenOutput Status Hour Meter ScreenInput Status Input Status ScreenService Menu Screen System Backup ScreenService Alarm Screens Alarm Screen Example Redundant Safety Controller DisplayAlways put your set point to 30F above set point Setting the Redundant Safety ControllerLarge Dehumidifying Dryers Controls Start-up OperationUsing the Dryer Status Screen Alarm Descriptions AlarmsShutdown Photocopy this page for your maintenance records MaintenanceMaintenance Schedule Cleaning or Replacing the Process Air Filters Preventative MaintenanceCalibrating the Dirty Filter Alarm Cleaning or Replacing the Regeneration FilterChecking the Dewpoint Control System Replacing the Desiccant Corrective MaintenanceSymptoms of Worn Out Desiccant Replacing the Process Heater Electric Dryers Desiccant Tower AssemblyReplacing the Regeneration Heater Electric Dryers Process Heater Box AssemblyRegeneration Heater Box Assembly Introduction TroubleshootingBasic Troubleshooting Large Dehumidifying Dryers Troubleshooting Using a Platinum Resistance Thermometer Determining Temperature Controller Errors or Sensor ErrorsUsing a Thermocouple Appendix WarrantyAnnex B Information Technical SpecificationsSpare Parts List Level 3 Mechanical Components Located on back of Dryer Dryer Identification Serial Number TagSales Department Service DepartmentTechnical Assistance Parts Department

882.00295.00 specifications

The Sterling 882.00295.00 is a remarkable piece of engineering that seamlessly combines functionality, durability, and aesthetic appeal in a compact form. Designed for those who require reliability and performance, this model stands out in its category, incorporating advanced technologies and user-friendly features.

One of the primary characteristics of the Sterling 882.00295.00 is its robust construction. The casing is made from high-quality materials that ensure resistance to wear and tear, making it suitable for various environments, whether industrial, commercial, or residential. Its sleek design not only provides visual appeal but also enhances its usability, allowing for easy integration into any workspace or setting.

The Sterling 882.00295.00 is equipped with state-of-the-art technology that enhances its performance. It features a precision-engineered mechanism that guarantees accurate readings and efficient operation. Users can rely on its consistent performance, whether for daily tasks or specialized applications. With enhanced data processing capabilities, this device can quickly analyze and display information, making it a valuable tool for professionals.

Another significant aspect of the Sterling 882.00295.00 is its user-centric design. The interface is intuitively organized, providing a seamless experience when navigating its features. This focus on usability ensures that operators of all skill levels can easily understand and utilize the device effectively. Additionally, the model often includes customizable settings, allowing users to tailor its functionality to meet specific needs.

In terms of connectivity, the Sterling 882.00295.00 supports modern protocols, enabling easy integration with other devices and systems. This feature is vital in today's interconnected world, where data sharing and collaboration are essential. Furthermore, it typically incorporates energy-efficient technologies, aligning with sustainable practices and reducing the overall carbon footprint.

Overall, the Sterling 882.00295.00 stands out for its blend of durability, advanced technology, and user-friendly features. It is a versatile solution that meets the demands of various users, from industrial professionals to everyday operators. With its focus on precision and efficiency, the Sterling 882.00295.00 is a valuable addition to any toolkit, ensuring that tasks are completed with the highest level of accuracy and reliability. Whether used in a high-stakes environment or for everyday applications, this model exemplifies the right combination of innovation and practicality.
Top Page Image Contents