HP BL10e manual Rack Airflow Requirements Rack 10000 series Cabinets, Service and Support

Page 9

QuickSpecs

HP ProLiant BL10e Generation 2 (G2) Server Blade

Standard Features

OS Support

NOTE: For a more complete and up-to-date listing of supported OSs and versions, please visit OS Support Matrix at:

 

http://www.hp.com/go/supportos.

 

NOTE: For a more complete and up-to-date information on Linux support, please visit HP Linux Web site at

 

http://h18000.www1.hp.com/products/servers/linux/hpLinuxcert.html.

 

NOTE: For a more complete and up-to-date information on Linux support, please visit HP Linux Web site at

 

http://h18000.www1.hp.com/products/servers/linux/hpLinuxcert.html.

 

 

Rack Airflow Requirements Rack 10000 series Cabinets

The increasing power of new high-performance processor technology requires increased cooling efficiency for rack-mounted servers. The 10000 Series Racks provide enhanced airflow for maximum cooling, allowing these racks to be fully loaded with servers using the latest processors.

CAUTION: If a third-party rack is used, observe the following additional requirements to ensure adequate airflow and to prevent damage to the equipment

 

Front and rear doors: If your 42U server rack includes closing front and rear doors, you must allow 5,350 sq cm (830

 

square inches) of hole evenly distributed from top to bottom to permit adequate airflow (equivalent to the required

 

64 percent open area for ventilation).

 

Side: The clearance between the installed rack component and the side panels of the rack must be a minimum of 7

 

cm (2.75 inches)

 

CAUTION: Always use blanking panels to fill all remaining empty front panel U-spaces in the rack. This arrangement

 

ensures proper airflow. Using a rack without blanking panels results in improper cooling that can lead to thermal damage.

 

NOTE: Please consult the Setup & Installation Guide for the server for additional details.

 

 

Service and Support

Three-year limited warranty, including hardware diagnostic support, pre-failure warranty (coverage of hard drives, memory

 

and processors). The warranty is fully supported by HP Services and a worldwide network of resellers and service providers. In

 

addition 90-day's getting started software telephone support may be covered under the warranty or available for an

 

additional fee. Enhancements to warranty services are available through HP Care Pack services.

 

NOTE: Sever Blade Limited Warranty includes 3 year Parts, 3 year Labor, 3-year on-site support.

 

NOTE: Server Blade Enclosure and Interconnects Limited Warranty includes 3 year Parts, 3 year Labor, 3-year on-site

 

support.

 

Care Pack services provide a range of life cycle support options that let you choose the service levels that meet your business

 

requirements, from basic to mission-critical.

 

A full range of HP Care Pack hardware and software services are available including:

 

Installation and start up

 

Education courses

 

Extended onsite hardware coverage hours from same business day 13 hours, 5 day to 24 hours, 7 days call window

 

with options including 4-hour response or 6-hour Call To Repair

 

Comprehensive range of software technical support for Microsoft, Linux, ProLiant Essentials and VMWare-based IT

 

solutions helping to deliver high level of application availability. Response times range from 30 mins for critical

 

problems to 2 hours.

 

System Management, Performance Services and Mission Critical Support Solution

 

HP Care Pack services for ProLiant BL p-Class server blades, cover the server blade and the p-Class blade enclosure that the

 

server blade is installed in as well as interconnects, power enclosure with power supplies and power distribution.

 

NOTE: For more information on HP Care Pack services, contact any of our worldwide sales offices or resellers or visit our

 

worldwide Web site on the internet at: http://www.hp.com/hps/carepack

 

NOTE: For more complete information on HP Services offerings, customers and resellers, please visit us at:

 

http://www.hp.com/hps

 

NOTE: Additional information regarding worldwide limited warranty and technical support is available at:

 

http://h18004.www1.hp.com/products/servers/platforms/warranty/index.html

DA - 11686 Worldwide — Version 13 — October 8, 2004

Page 9

Image 9
Contents Overview QuickSpecsWhats New ProLiant BL e-Class Integrated Administrator featuresProLiant BL10e G2 Server Blade includes ProLiant BL e-Class Server Blade Enclosure includesConfiguration Steps HP ProLiant BL10e G2 Server Blade Standard FeaturesHP ProLiant BL10e G2 Server Blade Enclosure HP ProLiant BL e-Class Interconnect TraysSupport for Network Time Protocol NTP HP ProLiant BL e-Class C-GbE Interconnect Switch FeaturesOther Options Diagnostic Adapter InterfacesFoundation Pack ProLiant EssentialsSoftware for the ProLiant BL ServerIndustry Standard SmartStartCompliance Intelligent ManageabilityRack Airflow Requirements Rack 10000 series Cabinets Service and SupportProLiant BL10e G2 Processor ModelsP1GHz-1MB ULV Cache Memory MB, 40-GB ATAOptions ProLiant Essentials UPS Options Uninterruptible Power Systems- RackR3000 XR Modular PDUs 1U/0U Up to 32 outletsDash # Description USB OptionsCustom Builder Tape Libraries HP StorageWorks ESL9000 Series Tape LibrariesRack Options for HP Rack 10000 Series HP Rack 10000 SeriesCountry Code Key for 1U Rack Keyboard & Drawer PN Installation & Start-up Services ProLiant BL10e G2 Server Blade MemoryMemory Slot Standard 512 MB Optional 640 MB 512 MB 128 MB 768 MB 256 MB Maximum 1024 MBTechnical Specifications Interconnect Switch Performance ConnectorForwarding Mode CompatibilityIeee 802.1Q Trunking Encapsulation Ieee 802.3x Flow Control