HP PB 10 manual Lanadmin -X 10fd, Etc/rc.config.d/hpBasetconf

Page 14

Installing and Configuring 10/100Base-TX/9000

Compatibility and Installation Requirements

To list the current speed and duplex mode of the HP-PB 10/100Base-TX/9000 card, use the -xoption (NOTE: lowercase x) of the lanadmin command. Determine the speed and duplex mode of your hub or switch before performing manual configuration as follows:

lanadmin -xppa (HP-UX 10.30 or 11.0) lanadmin -xnmid (HP-UX 10.20)

To manually set the duplex mode of the interface, install one of the patches above and then use the -Xoption of lanadmin as follows:

lanadmin -X mode ppa (on HP-UX 10.30 and 11.0) lanadmin -X mode nmid (on HP-UX 10.20)

where

:mode can be any one of the following strings (and the fd or hd are case-insensitive):

10fd =10 full-duplex 10hd =10 half-duplex

100fd =100 full-duplex 100hd =100 half-duplex

and

lanadmin -X auto_on ppa (turns autonegotiation on for HP-UX 10.30 and 11.0)

lanadmin -X auto_on nmid (turns autonegotiation on for HP-UX 10.20)

The ppa is the physical point of attachment on HP-UX 10.30 or 11.0. On HP-UX 10.20, use the nmid or Network Management ID of the card. You can get the ppa (nmid) from the output of the lanscan command.

Example:

If the ppa (nmid on HP-UX 10.20) of the 100Base-TX interface is 5, the command to set the card to 10Mbits/s and full-duplex mode would be:

lanadmin -X 10fd 5

After issuing the lanadmin -X, you must wait at least 11 seconds before attempting to use the specified network interface.

If you want the duplex mode setting to be effective in all subsequent reboots, you must enter the information in the following file:

/etc/rc.config.d/hpBasetconf

14

Chapter 1

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Using HP-PB 10/100Base-TX/9000 Manufacturing Part Number J2760-90017 E0699Legal Notices Page Page Contents Troubleshooting 10/100Base-TX/9000 100Base-TX ResourcesHardware Regulatory Statements 10/100Base-TX Interface Card StatisticsHardware Reference Information Contents Installing and Configuring Introduction AnnouncementsRequired and Optional Patches Compatibility and Installation Requirements Manual Speed and Duplex Mode Configuration Lanadmin -X 10fd Etc/rc.config.d/hpBasetconfHPBaseTINTERFACENAME0=lan3 HPBaseTSPEED0=10FD 100FD autoon Autonegotiation and Autosensing Known Problems and Workarounds Known Problems and WorkaroundsWhat Manuals are Available Software Availability in Native LanguagesOverview of Installation Steps Check the 10/100Base-TX Installation Prerequisites 10/100Base-TX/9000 Card Summary Category 10/100Base-TXLoading 10/100Base-TX Software Loading 10/100Base-TX Software Access the System Card Bay Install the 10/100Base-TX Card Attach the System to the Network Configure the 10/100Base-TX Link to configure the card Attach the System to the Network Configure the 10/100Base-TX Link first configuration of the card Configure the 10/100Base-TX Link Verifying the Installation To exit the utility, enter What Happens During Card Initialization Sequence? Configuring Network Configuring Network Connectivity Using SAM Configuring Network Connectivity More /etc/hosts Deleting a Default Gateway Deleting a Default Gateway 100Base-TX Resources HP-UX Manual Reference Pages Chapter Error Messages Logging Messages To stop 100Base-TX tracing Manual Installation and Configuration Contacting Your HP Representative Contacting Your HP Representative Contacting Your HP Representative Troubleshooting 10/100Base-TX/9000 Troubleshooting 10/100Base-TX/9000 Troubleshooting Overview Troubleshooting Information Symptom Corrective ActionTroubleshooting Overview Following HP-PB 10/100Base-TX LED Matrix Diagnostic Flowcharts Flowchart DescriptionsDiagnostic Flowcharts Flowchart 1 Network Level Loopback Test Correct BIND, YP or hosts configuration . Add Flowchart 2 10/100Base-TX Connections/LED Test YesSteps D through G in Flowchart 4. If problem Flowchart 2 ProceduresCheck card installation. Reset card according to Dmesg command, and look for an error messageFlowchart 2a 10/100Base-TX Connections/LED Test Diagnostic Flowcharts Flowchart 3 Configuration Test Flowchart 3 Procedures Is your interface displayed? lanscan showsIs driver in kernel? If the driver has not been Reboot the system Flowchart 4 Configuration Test Check causes and actions on display Flowchart 4 ProceduresReset the card according to Steps D through G Select LAN from Menu. Select lan from the menu toFlowchart 4A Configuration Test Flowchart 4A Procedures Flowchart 5 Configuration Test Flowchart 5 Procedures UP,BROADCAST, NOTRAILERS, RunningDiagnostic Flowcharts Flowchart 6 Network Level Loopback Test Use arp to complete entry. Using arp, enter Flowchart ProceduresHost entry in ARP cache? Using arp, check that an Flowchart 7 Link Level Loopback Test FailedFlowchart 7 Procedures Diagnostic Flowcharts Flowchart 8 Transport Level Loopback Test using Arpa Flowchart 8 Procedures Execute telnet to remote host. Try to establish aFlowchart 9 Bridge/Gateway Loopback Test Flowchart 9 Procedures Gateway 10/100Base-TX Interface Card 10/100Base-TX Interface Card Statistics MTU Size Field Description Network Management IDType value Speed in bits per secondLast Change Administration StatusOperation Status Inbound OctetsInbound Unknown Protocols Inbound ErrorsInbound Discards Outbound OctetsOutbound Errors Outbound Queue LengthRFC 1284 Ethernet-Like Interface Statistics Internal MAC Receive Errors Internal MAC Transmit ErrorsCarrier Sense Errors Frames Too LongCreate a Record or Map of Your Internetwork Create a Record or Map of Your Internetwork Hardware Reference Information Basic Troubleshooting Tips 10 or 100 Mbit/sAppendix B Meaning of LEDs If this LED is on It means thisConnector Pin Usage for 10-Mbit/s Twisted-Pair Connector Connector InformationHP-PB 10/100Base-TX Card Twisted-Pair Connector Table B-1 Ieee 802.3 Type 10Base-T Standard Pins SignalTable B-1 Ieee 802.3 Type 10Base-T Standard Connector Pin Usage for 100-Mbit/s Twisted-PairPins Signal Receive + Cable Lengths HP-PB 10/100Base-TX Card Reshipment Guidelines Exchange AssemblyElectromagnetic HP-PB 10/100Base-TX Card 104 Hardware Regulatory Statements 106 FCC Statement For U.S.A CanadaVcci Regulatory Statemen Vcci JapanEMI Statement European Community Glossary 109Ieee 802.3u-1995 network a 110111 112

PB 10 specifications

The HP PB10 is an impressive addition to HP's line of power banks, offering a perfect blend of portability, performance, and convenience. Designed for users on the go, the PB10 stands out for its compact size, making it easy to slip into a bag or pocket. This power bank is particularly appealing to tech-savvy individuals and frequent travelers who require a reliable source of energy to keep their devices powered throughout the day.

One of the main features of the HP PB10 is its impressive capacity. With a battery capacity of around 10,000 mAh, the power bank can charge a smartphone multiple times on a single charge, ensuring that users remain connected without running out of battery life. Its ability to charge various devices, including smartphones, tablets, and other USB-powered gadgets, makes it highly versatile.

The HP PB10 integrates advanced charging technologies to enhance performance. It includes Power Delivery (PD) that supports rapid charging for compatible devices, allowing users to power up their devices much faster than traditional charging methods. Additionally, the smart output technology optimizes power delivery, ensuring that devices receive the right amount of current for safe operation.

Another notable characteristic of the HP PB10 is its dual output ports. This feature allows users to charge two devices simultaneously, which is incredibly beneficial for those who need to juggle multiple gadgets. This capability is coupled with smart protection technology that guards against overheating, overcharging, and short-circuiting, ensuring the safety of both the power bank and the devices being charged.

The design of the HP PB10 is sleek and modern, featuring a durable casing that can withstand daily wear and tear. The LED indicator lights provide a clear status update on battery levels, so users always know how much power they have remaining. Lightweight and easy to carry, the HP PB10 is ideal for anyone looking for a reliable power source without adding bulk to their carry-on.

In conclusion, the HP PB10 power bank combines capacity, advanced charging technologies, dual output options, and safety features into a compact and stylish design. This makes it an essential accessory for anyone who lives an active lifestyle or relies heavily on their devices throughout the day. Whether traveling, commuting, or simply out and about, the HP PB10 ensures you're never caught without power.
Top Page Image Contents