HP PB 10 manual Check the 10/100Base-TX Installation Prerequisites

Page 20

NOTE

Installing and Configuring 10/100Base-TX/9000

Step 1: Check the 10/100Base-TX Installation Prerequisites

Step 1: Check the 10/100Base-TX Installation Prerequisites

The 10/100Base-TX card is a combination card that allows you to connect to a 10Mbit/s 10Base-T or 100 Mbit/s 100Base-TX network. The hardware card will be referred to as a 10/100Base-TX card throughout this manual.

Prior to loading the 10/100Base-TX product onto your system, check that you have met the following hardware and software prerequisites:

1.Check that the /usr/bin,/usr/sbin, and /sbin directories are in your PATH using the command:

echo $PATH

2.The operating system should have been upgraded to 10.20 or later software.

To obtain this information, execute the command:

/bin/uname -a

3.You have a twisted pair cable to connect your 10/100Base-TX card to your hub. (The cable and hub do not come with the HP 10/100Base-TX product.) A hardware checklist is shown below:

A.Cable: category 5 unshielded twisted pair (UTP).

B.Card: HP 9000 10/100Base-TX card.

C.Hub or switch: 100Base-TX hub for 100 Mbit/s speed

10Base-T hub for 10 Mbit/s speed.

4.Ensure that there is at least one HP-PB slot available in the system backplane for the HP-PB 10/100Base-TX card.

5.You have an IP/Internet address, alias, and subnet mask (optional), for your new 10/100Base-TX card. After you have obtained the information, fill out the Network Card Configuration worksheet in your 10/100Base-TX quick installation card.

A summary of the major characteristics of the 10/100Base-TX card is

20

Chapter 1

Image 20
Contents Using HP-PB 10/100Base-TX/9000 Manufacturing Part Number J2760-90017 E0699Legal Notices Page Page Contents Troubleshooting 10/100Base-TX/9000 100Base-TX ResourcesHardware Regulatory Statements 10/100Base-TX Interface Card StatisticsHardware Reference Information Contents Installing and Configuring Introduction AnnouncementsRequired and Optional Patches Compatibility and Installation Requirements Manual Speed and Duplex Mode Configuration Lanadmin -X 10fd Etc/rc.config.d/hpBasetconfHPBaseTINTERFACENAME0=lan3 HPBaseTSPEED0=10FD 100FD autoon Autonegotiation and Autosensing Known Problems and Workarounds Known Problems and WorkaroundsWhat Manuals are Available Software Availability in Native LanguagesOverview of Installation Steps Check the 10/100Base-TX Installation Prerequisites 10/100Base-TX/9000 Card Summary Category 10/100Base-TXLoading 10/100Base-TX Software Loading 10/100Base-TX Software Access the System Card Bay Install the 10/100Base-TX Card Attach the System to the Network Configure the 10/100Base-TX Link to configure the card Attach the System to the Network Configure the 10/100Base-TX Link first configuration of the card Configure the 10/100Base-TX Link Verifying the Installation To exit the utility, enter What Happens During Card Initialization Sequence? Configuring Network Configuring Network Connectivity Using SAM Configuring Network Connectivity More /etc/hosts Deleting a Default Gateway Deleting a Default Gateway 100Base-TX Resources HP-UX Manual Reference Pages Chapter Error Messages Logging Messages To stop 100Base-TX tracing Manual Installation and Configuration Contacting Your HP Representative Contacting Your HP Representative Contacting Your HP Representative Troubleshooting 10/100Base-TX/9000 Troubleshooting 10/100Base-TX/9000 Troubleshooting Overview Troubleshooting Information Symptom Corrective ActionTroubleshooting Overview Following HP-PB 10/100Base-TX LED Matrix Diagnostic Flowcharts Flowchart DescriptionsDiagnostic Flowcharts Flowchart 1 Network Level Loopback Test Correct BIND, YP or hosts configuration . Add Flowchart 2 10/100Base-TX Connections/LED Test YesFlowchart 2 Procedures Check card installation. Reset card according toSteps D through G in Flowchart 4. If problem Dmesg command, and look for an error messageFlowchart 2a 10/100Base-TX Connections/LED Test Diagnostic Flowcharts Flowchart 3 Configuration Test Flowchart 3 Procedures Is your interface displayed? lanscan showsIs driver in kernel? If the driver has not been Reboot the system Flowchart 4 Configuration Test Flowchart 4 Procedures Reset the card according to Steps D through GCheck causes and actions on display Select LAN from Menu. Select lan from the menu toFlowchart 4A Configuration Test Flowchart 4A Procedures Flowchart 5 Configuration Test Flowchart 5 Procedures UP,BROADCAST, NOTRAILERS, RunningDiagnostic Flowcharts Flowchart 6 Network Level Loopback Test Use arp to complete entry. Using arp, enter Flowchart ProceduresHost entry in ARP cache? Using arp, check that an Flowchart 7 Link Level Loopback Test FailedFlowchart 7 Procedures Diagnostic Flowcharts Flowchart 8 Transport Level Loopback Test using Arpa Flowchart 8 Procedures Execute telnet to remote host. Try to establish aFlowchart 9 Bridge/Gateway Loopback Test Flowchart 9 Procedures Gateway 10/100Base-TX Interface Card 10/100Base-TX Interface Card Statistics Field Description Network Management ID Type valueMTU Size Speed in bits per secondAdministration Status Operation StatusLast Change Inbound OctetsInbound Errors Inbound DiscardsInbound Unknown Protocols Outbound OctetsOutbound Errors Outbound Queue LengthRFC 1284 Ethernet-Like Interface Statistics Internal MAC Transmit Errors Carrier Sense ErrorsInternal MAC Receive Errors Frames Too LongCreate a Record or Map of Your Internetwork Create a Record or Map of Your Internetwork Hardware Reference Information Basic Troubleshooting Tips 10 or 100 Mbit/sAppendix B Meaning of LEDs If this LED is on It means thisConnector Information HP-PB 10/100Base-TX Card Twisted-Pair ConnectorConnector Pin Usage for 10-Mbit/s Twisted-Pair Connector Table B-1 Ieee 802.3 Type 10Base-T Standard Pins SignalTable B-1 Ieee 802.3 Type 10Base-T Standard Connector Pin Usage for 100-Mbit/s Twisted-PairPins Signal Receive + Cable Lengths HP-PB 10/100Base-TX Card Reshipment Guidelines Exchange AssemblyElectromagnetic HP-PB 10/100Base-TX Card 104 Hardware Regulatory Statements 106 FCC Statement For U.S.A CanadaVcci Regulatory Statemen Vcci JapanEMI Statement European Community Glossary 109Ieee 802.3u-1995 network a 110111 112

PB 10 specifications

The HP PB10 is an impressive addition to HP's line of power banks, offering a perfect blend of portability, performance, and convenience. Designed for users on the go, the PB10 stands out for its compact size, making it easy to slip into a bag or pocket. This power bank is particularly appealing to tech-savvy individuals and frequent travelers who require a reliable source of energy to keep their devices powered throughout the day.

One of the main features of the HP PB10 is its impressive capacity. With a battery capacity of around 10,000 mAh, the power bank can charge a smartphone multiple times on a single charge, ensuring that users remain connected without running out of battery life. Its ability to charge various devices, including smartphones, tablets, and other USB-powered gadgets, makes it highly versatile.

The HP PB10 integrates advanced charging technologies to enhance performance. It includes Power Delivery (PD) that supports rapid charging for compatible devices, allowing users to power up their devices much faster than traditional charging methods. Additionally, the smart output technology optimizes power delivery, ensuring that devices receive the right amount of current for safe operation.

Another notable characteristic of the HP PB10 is its dual output ports. This feature allows users to charge two devices simultaneously, which is incredibly beneficial for those who need to juggle multiple gadgets. This capability is coupled with smart protection technology that guards against overheating, overcharging, and short-circuiting, ensuring the safety of both the power bank and the devices being charged.

The design of the HP PB10 is sleek and modern, featuring a durable casing that can withstand daily wear and tear. The LED indicator lights provide a clear status update on battery levels, so users always know how much power they have remaining. Lightweight and easy to carry, the HP PB10 is ideal for anyone looking for a reliable power source without adding bulk to their carry-on.

In conclusion, the HP PB10 power bank combines capacity, advanced charging technologies, dual output options, and safety features into a compact and stylish design. This makes it an essential accessory for anyone who lives an active lifestyle or relies heavily on their devices throughout the day. Whether traveling, commuting, or simply out and about, the HP PB10 ensures you're never caught without power.