Thermo Products CDX1-75N, CHX1-125N, CHX1-75N, CHX1-100N, CDX1-125N CDX1 Models Counterflows

Page 30

All installations and services must be performed by qualified service personnel.

This CHX1 furnace has been factory supplied with a high quality re-usable filter rated for air velocities up to 600 ft/min. An optional Thermo Products filter rack assembly (part no. AOPS7547 for CHX1-75 thru 100 and AOPS7375 for CHX1-125) is available which is sized for the filter provided.

If an optional Thermo Pride filter rack AOPS7547 (figure 19) is used with the furnace, it will serve as a template to scribe a mark for the return air opening on the casing. Place the filter rack on the casing one inch up from the bottom of the furnace and centered from side to side. Place the securing flange against the casing for locating the return air opening.

Figure 19

PLEASE NOTE: While scribing the return air opening, the filter rack can be held into position by tape or similar means.

Position the open end of the filter rack so that it is accessible for filter replacement. Once the filter rack is positioned correctly, scribe a line along the inside of the securing flange of the filter rack on three of the sides. To scribe a line on the fourth side, on the open end, use the open end support for a guide.

Remove the filter rack and cut the return air opening in the casing. Now the filter rack can be permanently attached to the furnace with screws or pop-rivets along the securing flange.

Connect the return plenum to the filter rack and slide the filter into place.

2. CDX1 MODELS: COUNTERFLOWS

This CDX1 furnace has been factory supplied with two high quality reusable filters rated at 600 ft/min. These filters are designed to be mounted on the return air plenum opening on the top of the furnace in the double “vee” style rack provided (see Figure 20). If feasible, it is recommended that slits be cut in the return front to allow for easier access of the filters.

Figure 20

24

Page 29 Page 31
Image 30
Page 29 Page 31
Contents TWO Stage Condensing GAS Furnace MG-1010Safety Information Page Iii Page Index Section Beginning Height of Casing II. Furnace Specifications CHX1 Series Model noTemperature Rise Blower Motor HP Power Chokes Width of Casing Depth of CasingBTU/HR Output High fire / Low fire CDX1 Series Model noCDX1-75 CDX1-100 CDX1-125 BTU/HR Input High fire / Low fire @HEATING TAP C High fire / Low fireInstallation Parts Packages CHX1-75 Description Quantity #S00S4378#S00S4379 Installation Parts Packages CDX1-75 Description Quantity #S00S4380#S00S4381 III. General Installation Codes and ClearancesCHX1-75 CHX1-100 CHX1-125 CDX1-75 CDX1-100 CDX1-125 Furnace Location B1. CDX1 Horizontal ApplicationPage Replacing AN Existing Furnace from a Common Vent General Requirements for Venting CHX1/CDX1Maximum Vent Length Sidewall Venting Vent Terminal Location Requirements Vent Terminal Location Guidelines E1. Single Pipe Sidewall Venting OptionInstallation of Outside VENT/AIR Intake Terminations Optional TerminationsPage Page Connecting the Exhaust Vent to the Inducer Page Connecting the Combustion AIR Inlet Connecting the Furnace to Roof VENT/AIR Terminations Trap Assembly Mounted on CHX1 Trap Assembly Mounted on CDX1Page General GAS Piping Filters CHX1 Models Highboys CDX1 Models Counterflows Rate WiringUSE of NON-THERMO Pride Filter Retention Means AIR Velocity Furnace ModelElectronic AIR Cleaner EAC and Humidifier Installation Thermostat Connections and Anticipator SettingBlower and Control Panel Wiring CFM Settings Low fire High fire CDX1-75Field Wiring and Replacing Wiring CHX1-75Contacts Close Retry will be Made If System is in Lockout Initial Start UP Operating InstructionsGas flowrate by clocking gas meter Exploded View of CDX/CHX Gas Control System BTU Normal Manifold CHX Low CDX LowCHX Low CDX Low Model Series Pressure in. W.GChecking The Burner Flame Checkout Procedure Sketch of Typical Main Burner Flames During OperationConverting GAS Flow Rate Furnace Checkout Procedure Installers Instructions to UserVI. Troubleshooting Diagnostic Features Terminals IND HI to IND N or IND LO to Is the High Limit Page 50V61-143 Control AIR Blower Turn OFF Replacement parts list for CHX1-75, CHX1-100 and CHX1-125 Page Replacement parts list for CDX1-75, CDX1-100 and CDX1-125 Page Appendix B Wiring Diagrams
Related manuals
Manual 59 pages 55.22 Kb

CDX1-100N, CDX1-125N, CHX1-100N, CHX1-75N, CHX1-125N specifications

Thermo Products has established itself as a leader in the HVAC industry, providing innovative solutions for climate control with their latest product line, including the CHX1-125N, CDX1-75N, CDX1-100N, CHX1-75N, and CHX1-100N models. These units are designed for both efficiency and performance, catering to a wide range of heating and cooling needs.

One of the standout features of these models is their high energy efficiency ratings. Utilizing advanced inverter technology, these units dynamically adjust their operating frequency, optimizing energy consumption while maintaining consistent temperature control. This adaptability not only enhances comfort but also significantly lowers energy bills, making them an eco-friendly choice for both residential and commercial applications.

The CHX1 series, including the CHX1-125N, CHX1-75N, and CHX1-100N, is renowned for its robust build quality and superior performance in extreme conditions. They can operate effectively in varied environments, ensuring reliable heating during harsh winters and efficient cooling amid hot summers.

In contrast, the CDX1 series—featuring the CDX1-75N and CDX1-100N—focuses on delivering exceptional versatility. These models come equipped with advanced multi-zone capabilities, allowing users to control different areas or rooms with precision. This zoning capability not only enhances comfort but also optimizes energy efficiency by allowing users to heat or cool only the spaces that are occupied.

A common characteristic among all these models is their quiet operation. Designed with noise-reduction technologies, the units are engineered to operate with minimal sound, making them ideal for residential settings, offices, and other noise-sensitive environments.

Moreover, Thermo Products emphasizes user-friendly interfaces in their design. With intuitive controls and smart connectivity options, users can easily manage their HVAC systems through mobile applications, ensuring convenience and optimal temperature management from anywhere.

Overall, Thermo Products’ CHX1-125N, CDX1-75N, CDX1-100N, CHX1-75N, and CHX1-100N models exemplify the perfect blend of innovation, efficiency, and user-centered design. These heating and cooling solutions not only meet the demands of modern living but also contribute to sustainability efforts, making them a valuable addition to any climate control system.
Top Page Image Contents