HP 1000 manual Memory module

Page 39

Memory module

Description

Spare part number

 

 

1024-MB (PC2-4200, 533-MHz, DDR2)

504600-001

 

 

512-MB (PC2-4200, 533-MHz, DDR2)

504599-001

 

 

Before removing the memory module, follow these steps:

1.Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

2.Disconnect all external devices connected to the device.

3.Disconnect the power from the device by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the device.

4.Remove the battery (see Battery on page 30).

Remove the memory module:

1.Slide the right battery release latch to the inside or “unlocked” position to reveal the release latch for the memory module compartment cover. Use a thin, narrow tool to slide the release latch to the outside or “unlocked” position (1). (The edge of the cover rises away from the device.)

2.Remove the cover (2). The memory module compartment cover is included in the Plastics Kit, spare part number 507317-001.

3.Spread the retaining tabs (1) on each side of the memory module slot to release the memory module. (The edge of the module opposite the slot rises away from the device.)

Component replacement procedures 31

Page 38 Page 40
Image 39
Page 38 Page 40
Contents HP Mini 1000 NetBook First Edition October Document Part Number Safety warning notice Iv Safety warning notice Table of contents Setup Utility Connector pin assignments Viii Category Description Product descriptionWebcam WirelessPower requirements Operating system PreinstalledServiceability End-user replaceable parts Restore mediaComponent Function External component identificationTop components DisplayEsc key KeysTouchPad Control Panel Performance and Maintenance Power OptionsFront components Right-side components Left-side components Bottom components Serial number location Illustrated parts catalogDevice major components Description Spare part numberKeyboard Mass storage device Heat sink assembly not illustratedRTC battery Wireless module Broadcom 4312 802.11/b/g Wlan modulesBluetooth module BatteryHP un2400 Mobile Broadband Module Display enclosure includes logo Display assembly componentsSpeaker grill Webcam modulePlastics Kit Display panel foil shield not illustratedItem Description Spare part number Plastics Kit 507317-001 Miscellaneous parts Slip case Bracket KitSpare part Description Number Sequential part number listingIllustrated parts catalog Sequential part number listing Tools required Removal and replacement proceduresPreliminary replacement requirements Service considerationsDrive handling Grounding guidelines Typical electrostatic voltage levelsEvent 10% 40% 55% Packaging and transporting guidelines Material Use Voltage protection level Equipment guidelinesUnknown user password Service tag Component replacement proceduresDevice feet Battery Memory module Page Description Spare part number KeyboardPage Mass storage devices Page Top cover Page Page Top cover see Top cover on Wlan modulePage Description Spare part number RTC battery 507707-001 RTC batteryDescription Spare part number Bluetooth module 507706-001 Bluetooth moduleSystem board Page Page Description Spare part number Heat sink assembly 515099-001 Heat sink assemblyDescription Spare part number Fan 504615-001 FanDisplay assembly Page Page Page Page Page Page Changing the language of the Setup Utility Setup UtilityStarting the Setup Utility Using the Setup UtilityNavigating and selecting in the Setup Utility Restoring default settings in the Setup UtilityDisplaying system information Security menu Setup Utility menusExiting the Setup Utility Main menuSystem Configuration menu Diagnostics menuSelect To do this Specifications Device specificationsMetric Inch, Wsvga display specifications Height 12.53 cm Width 22.27 cm Diagonal 25.55 cm 10.06 60-GB Hard drive specificationsSolid-state drive specifications Hardware IRQ System function System DMA specificationsSystem interrupt specifications Hardware DMA System functionAddress hex System function shipping configuration System I/O address specificationsFFA0 Ffaf Memory address System function System memory map specificationsScrew listing Phillips PM1.6×2.5 screwColor Quantity Length Thread Head diameter Silver Color Quantity Length Thread Head diameter Phillips PM2.0×3.0 screwPhillips PM2.0×4.0 screw Page Page Phillips PM2.0×6.0 screw Phillips PM2.0×7.0 screw Phillips PM2.0×8.0 screw Phillips PM2.5×7.0 screw Phillips PM2.5×9.0 screw Backup and recovery When to back upBacking up your information Backing up individual files or folders Backup suggestionsBacking up all files and folders Creating recovery pointsPerforming a recovery Scheduling backupsInitiating a recovery in Windows Audio-out headphone Connector pin assignmentsPin Signal Audio-in microphoneUniversal Serial Bus RJ-45 networkRequirements for all countries and regions Power cord set requirementsCountry/region Accredited agency Applicable note number Requirements for specific countries and regionsBattery RecyclingDisplay Page Page Page Page Page Index Page Page
Related manuals
Manual 8 pages 26.72 Kb Manual 113 pages 27.43 Kb Manual 96 pages 21.47 Kb

1000 specifications

The HP 1000 was a series of minicomputers produced by Hewlett-Packard from the early 1970s through the late 1980s. Originally introduced in 1973, the HP 1000 aimed to provide high-performance computing capabilities within the reach of small to medium-sized businesses and specialized industries. This machine was distinctive not only for its advanced technology but also for the versatility it offered in various applications.

One of the standout features of the HP 1000 was its architecture. The system utilized a 16-bit word size, which allowed for efficient processing and execution of instructions. The HP 1000 employed a unique architecture known as the "Hewlett-Packard 1000 Microprogrammed System," which enabled it to execute a broad range of instructions efficiently. This made the HP 1000 particularly well-suited for data processing applications, scientific calculations, and high-level computing tasks.

The HP 1000 series was fully modular, allowing users to customize and expand their systems as needed. It supported various input/output devices, memory sizes, and even offered options for solid-state disk drives, which were cutting-edge for that time. The system’s modularity not only provided flexibility but also enhanced maintainability, enabling users to swap out components without significant downtime.

Another key aspect of the HP 1000 was its support for a wide range of programming languages, including FORTRAN, COBOL, and BASIC. This made it appealing to a variety of users, from engineers who needed to perform complex calculations to business analysts focused on data management. Additionally, the HP 1000 was designed to run multiple jobs simultaneously, making it a precursor to modern multitasking operating systems.

Networking capabilities were also an essential characteristic of the HP 1000. The system could be connected to various peripherals and terminals, increasing its functionality in a networked environment. This helped businesses leverage the power of shared resources, facilitating collaborative projects and data sharing across departments.

In conclusion, the HP 1000 series played a significant role in the evolution of computing technology. Its modular design, robust architecture, support for multiple programming languages, and networking capabilities made it a versatile tool for a wide range of applications. For over a decade, the HP 1000 series marked an important chapter in the history of computing, laying the groundwork for advancements in minicomputer technology that would follow.
Top Page Image Contents