HP 1000 manual Description Spare part number RTC battery 507707-001

Page 50

RTC battery

NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all passwords and CMOS settings to be cleared.

Description

Spare part number

 

 

RTC battery

507707-001

 

 

Before removing the real-time clock (RTC) battery, follow these steps:

1.Shut down the device. If you are unsure whether the device is off or in Hibernation, turn the device on, and then shut it down through the operating system.

2.Disconnect all external devices connected to the device.

3.Disconnect the power from the device by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the device.

4.Remove the battery (see Battery on page 30).

5.Remove the following components:

a.Keyboard (see Keyboard on page 33)

b.Hard drive or solid-state drive (see Mass storage devices on page 35)

c.Top cover (see Top cover on page 37)

Remove the RTC battery:

1.Disconnect the RTC battery cable (1) from the system board.

2.Detach the RTC battery (2) from the system board, and then remove the RTC battery.

NOTE: The RTC battery is attached to the system board with double-sided tape.

Reverse this procedure to install the RTC battery.

42 Chapter 4 Removal and replacement procedures

Image 50
Contents HP Mini 1000 NetBook First Edition October Document Part Number Safety warning notice Iv Safety warning notice Table of contents Setup Utility Connector pin assignments Viii Product description Category DescriptionOperating system Preinstalled WirelessPower requirements WebcamRestore media Serviceability End-user replaceable partsDisplay External component identificationTop components Component FunctionKeys Esc keyTouchPad Front components Control Panel Performance and MaintenancePower Options Right-side components Left-side components Bottom components Illustrated parts catalog Serial number locationKeyboard Device major componentsDescription Spare part number Wireless module Broadcom 4312 802.11/b/g Wlan modules Heat sink assembly not illustratedRTC battery Mass storage deviceHP un2400 Mobile Broadband Module Bluetooth moduleBattery Webcam module Display assembly componentsSpeaker grill Display enclosure includes logoItem Description Spare part number Plastics Kit 507317-001 Plastics KitDisplay panel foil shield not illustrated Miscellaneous parts Bracket Kit Slip caseSequential part number listing Spare part Description NumberIllustrated parts catalog Sequential part number listing Service considerations Removal and replacement proceduresPreliminary replacement requirements Tools requiredDrive handling Event 10% 40% 55% Grounding guidelinesTypical electrostatic voltage levels Packaging and transporting guidelines Equipment guidelines Material Use Voltage protection levelUnknown user password Component replacement procedures Service tagDevice feet Battery Memory module Page Keyboard Description Spare part numberPage Mass storage devices Page Top cover Page Page Wlan module Top cover see Top cover onPage RTC battery Description Spare part number RTC battery 507707-001Bluetooth module Description Spare part number Bluetooth module 507706-001System board Page Page Heat sink assembly Description Spare part number Heat sink assembly 515099-001Fan Description Spare part number Fan 504615-001Display assembly Page Page Page Page Page Page Using the Setup Utility Setup UtilityStarting the Setup Utility Changing the language of the Setup UtilityDisplaying system information Navigating and selecting in the Setup UtilityRestoring default settings in the Setup Utility Main menu Setup Utility menusExiting the Setup Utility Security menuSelect To do this System Configuration menuDiagnostics menu Metric SpecificationsDevice specifications Inch, Wsvga display specifications Height 12.53 cm Width 22.27 cm Diagonal 25.55 cm 10.06 Hard drive specifications 60-GBSolid-state drive specifications Hardware DMA System function System DMA specificationsSystem interrupt specifications Hardware IRQ System functionSystem I/O address specifications Address hex System function shipping configurationFFA0 Ffaf System memory map specifications Memory address System functionColor Quantity Length Thread Head diameter Silver Screw listingPhillips PM1.6×2.5 screw Phillips PM2.0×3.0 screw Color Quantity Length Thread Head diameterPhillips PM2.0×4.0 screw Page Page Phillips PM2.0×6.0 screw Phillips PM2.0×7.0 screw Phillips PM2.0×8.0 screw Phillips PM2.5×7.0 screw Phillips PM2.5×9.0 screw Backing up your information Backup and recoveryWhen to back up Backup suggestions Backing up individual files or foldersCreating recovery points Backing up all files and foldersInitiating a recovery in Windows Performing a recoveryScheduling backups Audio-in microphone Connector pin assignmentsPin Signal Audio-out headphoneRJ-45 network Universal Serial BusPower cord set requirements Requirements for all countries and regionsRequirements for specific countries and regions Country/region Accredited agency Applicable note numberDisplay BatteryRecycling Page Page Page Page Page Index Page Page
Related manuals
Manual 8 pages 26.72 Kb Manual 113 pages 27.43 Kb Manual 96 pages 21.47 Kb

1000 specifications

The HP 1000 was a series of minicomputers produced by Hewlett-Packard from the early 1970s through the late 1980s. Originally introduced in 1973, the HP 1000 aimed to provide high-performance computing capabilities within the reach of small to medium-sized businesses and specialized industries. This machine was distinctive not only for its advanced technology but also for the versatility it offered in various applications.

One of the standout features of the HP 1000 was its architecture. The system utilized a 16-bit word size, which allowed for efficient processing and execution of instructions. The HP 1000 employed a unique architecture known as the "Hewlett-Packard 1000 Microprogrammed System," which enabled it to execute a broad range of instructions efficiently. This made the HP 1000 particularly well-suited for data processing applications, scientific calculations, and high-level computing tasks.

The HP 1000 series was fully modular, allowing users to customize and expand their systems as needed. It supported various input/output devices, memory sizes, and even offered options for solid-state disk drives, which were cutting-edge for that time. The system’s modularity not only provided flexibility but also enhanced maintainability, enabling users to swap out components without significant downtime.

Another key aspect of the HP 1000 was its support for a wide range of programming languages, including FORTRAN, COBOL, and BASIC. This made it appealing to a variety of users, from engineers who needed to perform complex calculations to business analysts focused on data management. Additionally, the HP 1000 was designed to run multiple jobs simultaneously, making it a precursor to modern multitasking operating systems.

Networking capabilities were also an essential characteristic of the HP 1000. The system could be connected to various peripherals and terminals, increasing its functionality in a networked environment. This helped businesses leverage the power of shared resources, facilitating collaborative projects and data sharing across departments.

In conclusion, the HP 1000 series played a significant role in the evolution of computing technology. Its modular design, robust architecture, support for multiple programming languages, and networking capabilities made it a versatile tool for a wide range of applications. For over a decade, the HP 1000 series marked an important chapter in the history of computing, laying the groundwork for advancements in minicomputer technology that would follow.