HP H4H3 manual Inspect NEW Unit, Safety Considerations, Location, Clearances

Page 2

INSTALLATION INSTRUCTIONS

3-phase R-410A Split System Heat Pump

 

 

INSPECT NEW UNIT

After uncrating unit, inspect thoroughly for hidden damage. If damage is found, notify the transportation

company immediately and file a concealed damage claim.

SAFETY CONSIDERATIONS

Consult a qualified installer, service agency, or the

!

WARNING

 

 

dealer/distributor for information and assistance. The

 

qualified installer must use factory authorized kits and

 

 

 

ELECTRICAL SHOCK HAZARD

 

accessories when modifying this product. Refer to the

 

individual instructions packaged with the kit or accessory

Failure to follow this warning could result in per‐

 

when installing.

 

sonal injury or death.

 

The weight of the product requires careful and proper

 

Before installing, modifying or servicing system,

 

handling procedures when lifting or moving to avoid

 

turn OFF the main (remote) electrical disconnect

 

personal injury. Use care to avoid contact with sharp or

 

device. There may be more than one disconnect

 

pointed edges.

 

device.

 

 

 

 

 

Follow all safety codes. Wear safety glasses, protective

 

 

 

 

 

 

clothing, and work gloves. Use a heat sinking material -

 

 

 

!

CAUTION

 

such as a wet rag - during brazing operations. Keep a fire

 

 

 

 

extinguisher available. Consult local codes and the

 

 

 

 

 

 

National Electric Code (NEC) for special requirements.

PROPERTY DAMAGE HAZARD

 

Improper installation, adjustment, alteration, service or

Failure to follow this caution may result in proper‐

 

maintenance can void the warranty.

 

ty damage

 

 

 

 

 

 

R-410A systems operate at higher pressures than

 

 

R-22 systems. When working with R-410A sys‐

 

 

tems, use only service equipment and replace‐

 

 

ment components specifically rated or approved

 

 

for R-410A service.

 

LOCATION

 

 

 

 

 

 

Check local codes for regulations concerning zoning, noise, platforms, and other issues.

Locate unit away from fresh air intakes, vents, or bedroom windows. Noise may carry into the openings and disturb people inside.

Locate unit in a well drained area, or support unit high enough so that water runoff will not enter the unit.

Locate unit away from areas where heat, lint, or exhaust fumes will be discharged onto unit (as from dryer vents).

Locate unit away from recessed or confined areas where recirculation of discharge air may occur (refer to CLEARANCES section of this document).

Roof-top installation is acceptable providing the roof will support the unit and provisions are made for water drainage and noise/vibration dampening.

NOTE: Roof mounted units exposed to wind may require wind baffles. Consult the manufacturer for additional information.

CLEARANCES

Nominal minimum clearances are 48 inches above unit for discharge air and 18 inches on each side of the coil for intake air. Clearance on any one side of the coil (normally between unit and structure) may be reduced to 6 inches. Nominal minimum clearances are based on a solid parallel object such as a wall or roof overhang.

The clearance may be reduced for a single object with small surface area, such as the end of a wall, outside corner of a wall, fence section, post, etc. As a general rule, the minimum clearance from the unit should equal the width of the object. For example, a 6 inch fence post should be a minimum of 6 inches from the unit.

Do not install unit under roof overhangs unless gutters are present. A minimum vertical clearance of 48 inches is required to the overhang.

Inside corner locations on single story structures require evaluation. Large overhanging soffits may cause air recirculation in a corner area even though recommended minimum clearances are maintained. As a guide, locate the unit far enough out so that half of the discharge grille is out from under the soffit.

When placing two or more units side-by-side, provide a minimum of 18 inches between units.

Provide minimum service clearance of 24 inches from control box corner and side service panel.

Refer to Figure 1.

2

506 01 5102 00

Image 2
Contents Installation Instructions Table of ContentsLocation Safety ConsiderationsInspect NEW Unit ClearancesClearances various examples Unit Support Ground Level InstallationRoof TOP Installation Fastening Unit DownRefrigeration System Liquid Line Filter-Drier Installed at Indoor CoilRouting and Suspending Refrigerant Lines Outdoor Unit Higher than Indoor UnitEvacuating Line SET and Indoor Coil Installation Instructions Service ValvesBrazing Connections Fire Hazard System Conditions Opening Service ValvesDeep Vacuum Gauge Response Triple Evacuation MethodElectrical Wiring Typical Thermostat Control Circuit Connections Defrost Thermostat Defrost SystemDefrost Thermostat Defrost Control BoardHeating Mode START-UP ProcedureCooling Mode Refrigerant ChargeSequence of Operation Troubleshooting MaintenanceYellow Alert Reverse Phase Comfort Alertt Diagnostics some modelsYellow Alert Missing Phase Red Trip LEDAlert Flash Code 410A Quick Reference GuideTrip LED and Alert LED Alert Flash Code 5 or

H4H3 specifications

The HP H4H3 is a versatile and efficient device designed primarily for business and professional use. This printer exemplifies HP's commitment to innovation, focusing on performance, quality, and convenience. One of the standout features of the HP H4H3 is its ability to produce high-quality prints at an impressive speed, making it ideal for busy office environments. The printer is capable of delivering professional-grade documents with a resolution that can reach up to 1200 x 1200 dpi, ensuring that text and images come out crisp and vibrant.

One of the key technologies that enhance the functionality of the HP H4H3 is the HP LaserJet technology, which allows for faster warm-up times and reduced energy consumption compared to traditional laser printers. This tech not only optimizes power usage but also minimizes the environmental impact, aligning with modern sustainability goals. Another significant characteristic is its robust paper handling capabilities, which can accommodate various paper sizes and types, ranging from envelopes to legal-sized documents. This versatility allows users to tackle various printing tasks without the need for constant paper changes.

The HP H4H3 also incorporates advanced connectivity features, such as USB, Ethernet, and wireless options, providing flexibility in how users choose to connect their devices. The inclusion of mobile printing capabilities through HP Smart App and other cloud services provides users with the convenience of printing from smartphones and tablets, catering to an increasingly mobile workforce.

Security is another focal area in the design of the HP H4H3. It comes equipped with robust built-in security features that help protect sensitive data from unauthorized access. With options for secure printing and user authentication, it ensures that confidential documents remain secure, even in shared environments.

Furthermore, the printer is designed with user-friendliness in mind, featuring an intuitive control panel that simplifies navigation and settings adjustments. The HP H4H3 also supports automatic duplex printing, reducing paper consumption and further promoting eco-friendly practices in the workplace.

In summary, the HP H4H3 stands out due to its impressive print quality, fast performance, numerous connectivity options, and strong security features. It is a reliable choice for businesses looking to enhance their printing capabilities while prioritizing efficiency and sustainability. Whether for everyday documents or high-stakes presentations, the HP H4H3 delivers exceptional results that meet the demands of modern work environments.