HP H4H3 manual Unit Support, Ground Level Installation, Roof TOP Installation, Fastening Unit Down

Page 4

INSTALLATION INSTRUCTIONS

3-phase R-410A Split System Heat Pump

 

 

UNIT SUPPORT

NOTE: Unit must be level 2 degrees (a inch rise or fall per foot of run) or compressor may not function properly.

Figure 2

Tie Down Knockouts

 

 

A. GROUND LEVEL INSTALLATION

The unit must be level and supported above grade by beams, platform, or a pad. Platform or pad can be of open or solid construction but should be of permanent materials such as concrete, bricks, blocks, steel, or pressure- treated timbers approved for ground contact. Soil conditions must be considered so that the platform or pad does not shift or settle and leave the unit partially supported. Minimum pad dimensions are shown in Figure 2.

If beams or an open platform are used for support, it is recommended that the soil be treated or area be graveled to reduce the growth of grasses and weeds.

a” dia. Tie Down Knockouts In Base Pan (2 places)

View From Top Product Family: H series

Base

Pan

Depth

To minimize vibration or noise transmission, it is recommended that supports not be in contact with the building structure. However, slabs on grade constructions with an extended pad are normally acceptable.

! CAUTION

PROPERTY DAMAGE HAZARD

Failure to follow this caution may result in proper‐ ty damage.

Top surface of platform must be above estimated snowfall level to prevent snow blocking coil and to allow water melt to drain from unit.

B. ROOF TOP INSTALLATION

This type of installation is not recommended on wood frame structures where low noise levels are required.

Supporting structure or platform for the unit must be level. If installation is on a flat roof, locate unit minimum 6 inches above roof level.

Place the unit over one or more load bearing walls. If there are several units, mount them on platforms that are self-supporting and span several load bearing walls. These suggestions are to minimize noise and vibration transmission through the structure. If the structure is a home or apartment, avoid locating the unit over bedrooms or study.

NOTE: When unit is to be installed on a bonded guaranteed roof, a release must be obtained from the building owner to free the installer from all liabilities.

C. FASTENING UNIT DOWN

If conditions or local codes require the unit be attached in place, remove the knockouts in the base pan and install tie down bolts through the holes (refer to Figure 2).

Contact local distributor for hurricane hold-down details and the P.E. (Professional Engineer) certification, when required.

C

 

 

 

 

B

A

 

 

 

 

 

Base Pan Width

 

 

Base Pan

 

Tie Down

Minimum

(Bumpout)

Knockouts

Mounting Pad

Width x Depth

 

 

 

A

B

C

Dimensions

(inches)

@%n ~ @^c

(z

$v

@!4

@^ X~ @^2

#!8 ~ #@v

(z

^2

@$s

#!2 ~ #@2

#$, ~ #^2

(z

^2

@*v

#% ~ #^2

!CAUTION

PROPERTY DAMAGE HAZARD

Failure to follow this caution may result in property damage.

Inadequate unit support may cause excessive vibra‐ tion, noise, and/or stress on the refrigerant lines, leading to refrigerant line failure.

4

506 01 5102 00

Image 4
Contents Installation Instructions Table of ContentsSafety Considerations Inspect NEW UnitLocation ClearancesClearances various examples Ground Level Installation Roof TOP InstallationUnit Support Fastening Unit DownRefrigeration System Installed at Indoor Coil Routing and Suspending Refrigerant LinesLiquid Line Filter-Drier Outdoor Unit Higher than Indoor UnitBrazing Connections Fire Hazard Installation Instructions Service ValvesEvacuating Line SET and Indoor Coil Opening Service Valves Deep Vacuum Gauge ResponseSystem Conditions Triple Evacuation MethodElectrical Wiring Typical Thermostat Control Circuit Connections Defrost System Defrost ThermostatDefrost Thermostat Defrost Control BoardSTART-UP Procedure Cooling ModeHeating Mode Refrigerant ChargeSequence of Operation Troubleshooting MaintenanceComfort Alertt Diagnostics some models Yellow Alert Missing PhaseYellow Alert Reverse Phase Red Trip LED410A Quick Reference Guide Trip LED and Alert LEDAlert Flash Code Alert Flash Code 5 or

H4H3 specifications

The HP H4H3 is a versatile and efficient device designed primarily for business and professional use. This printer exemplifies HP's commitment to innovation, focusing on performance, quality, and convenience. One of the standout features of the HP H4H3 is its ability to produce high-quality prints at an impressive speed, making it ideal for busy office environments. The printer is capable of delivering professional-grade documents with a resolution that can reach up to 1200 x 1200 dpi, ensuring that text and images come out crisp and vibrant.

One of the key technologies that enhance the functionality of the HP H4H3 is the HP LaserJet technology, which allows for faster warm-up times and reduced energy consumption compared to traditional laser printers. This tech not only optimizes power usage but also minimizes the environmental impact, aligning with modern sustainability goals. Another significant characteristic is its robust paper handling capabilities, which can accommodate various paper sizes and types, ranging from envelopes to legal-sized documents. This versatility allows users to tackle various printing tasks without the need for constant paper changes.

The HP H4H3 also incorporates advanced connectivity features, such as USB, Ethernet, and wireless options, providing flexibility in how users choose to connect their devices. The inclusion of mobile printing capabilities through HP Smart App and other cloud services provides users with the convenience of printing from smartphones and tablets, catering to an increasingly mobile workforce.

Security is another focal area in the design of the HP H4H3. It comes equipped with robust built-in security features that help protect sensitive data from unauthorized access. With options for secure printing and user authentication, it ensures that confidential documents remain secure, even in shared environments.

Furthermore, the printer is designed with user-friendliness in mind, featuring an intuitive control panel that simplifies navigation and settings adjustments. The HP H4H3 also supports automatic duplex printing, reducing paper consumption and further promoting eco-friendly practices in the workplace.

In summary, the HP H4H3 stands out due to its impressive print quality, fast performance, numerous connectivity options, and strong security features. It is a reliable choice for businesses looking to enhance their printing capabilities while prioritizing efficiency and sustainability. Whether for everyday documents or high-stakes presentations, the HP H4H3 delivers exceptional results that meet the demands of modern work environments.