York DM 072 warranty Guide Specifications, General, Description

Page 42

GUIDE SPECIFICATIONS

GENERAL

Units shall be manufactured by York International Unitary Products Group in an ISO 9001 certified facility.

York's Sunline 2000TM units are convertible single package- units. Although the units are primarily designed for curb mounting on a roof, they can also be slab-mounted at ground level or set on steel beams above a finished roof. Cooling only, cooling with gas heat and cooling with electric heat models are available with a wide variety of factory-mounted options and field-installed accessories to make them suitable for almost every application. All units are self-contained and assembled on full perimeter base rails with holes in the four corners for overhead rigging. Every unit is completely piped, wired, charged and tested at the factory to simplify the field installation and to provide years of dependable operation. All models (including those with an economizer) are suitable for either bottom or horizontal duct connections. Models with power exhaust are suitable for bottom duct connections only. For bottom duct, remove the sheet metal panels from the supply and return air openings through the base of the unit. For horizontal duct, remove the supply and return air panels on the rear of the unit.

All non-Scroll compressors include crankcase heaters and all compressors have internal pressure relief. Every refrigerant circuit includes a liquid line filter-drier, a discharge line high pressure switch and a suction line with a freezestat and low pressure/loss of charge switch.The unit control circuit includes a 75 VA transformer, a 24-volt circuit breaker and a relay board with a compressor lockout circuit, a terminal strip for thermostat wiring, plus an additional set of pin connectors to simplify the interface of additional field controls. All units have long lasting powder paint cabinets with 1000 hour salt spray test approval under ASTMB117 procedures. All models are CSA listed. All models include a 1-year limited warranty on the complete unit. Compressors and electric heater ele- ments carry a 5-year warranty. Aluminized steel and Stainless steel tubular heat exchangers carry a 10-year warranty.

DESCRIPTION

Units shall be factory-assembled, single packaged, Electric Cooling/Gas Heat, Electric Cooling/Optional Electric Heat and designed for outdoor mounted installation.

The 3 thru 5 ton units shall have minimum SEER ratings of

10.0and the 6 ton units shall have minimum EER ratings of 9.0. They shall have built-in field convertible duct connections for down discharge supply/return or horizontal discharge sup- ply/return, and be available with factory installed options or field installed accessories. The units shall be factory wired, piped, charged with R-22 refrigerant and factory tested prior to shipment. All unit wiring shall be both numbered and color coded. All units the cooling performance shall be rated in accordance with DOE and ARI test procedures. Units shall be CSA listed, classified to ANSI Z21.47, UL 1995/CSA No. 236 standards.

036-21502-003-A-1105

UNIT CABINET

Unit cabinet shall be constructed of G90 galvanized steel, with exterior surfaces coated with a non-chalking, powdered paint finish, certified at 1000 hours salt spray test per ASTMB117 standards. Indoor blower section shall be insu- lated with a minimum 1/2” thick insulation, coated on the air- side. Aluminum foil faced insulation shall be used in the furnace compartment and be fastened with ridged fasteners to prevent insulation from entering the air stream. Cabinet panels shall be “large” size, easily removable for servicing and maintenance. Full perimeter base rails shall be provided to assure reliable transit of equipment, overhead rigging and proper sealing on roof curb applications. Disposable 1" filters shall be furnished and be accessible through a removable access door, sealed airtight. Units filter track shall be designed to accommodate either 1” or 2” filters. Fan perfor- mance measuring ports shall be provided on the outside of the cabinet to allow accurate air measurements of evaporator fan performance without removing panels or creating air by- pass of the coils. Condensate pan shall be internally sloped and conform to ASHRAE 62-89 self-draining standards. Con- densate connection shall be a minimum of 3/4” I.D. female and be a ridged mount connection.

INDOOR (EVAPORATOR) FAN ASSEMBLY

The indoor fan shall be direct drive, multi-speed, or a factory installed belt drive assembly that includes an adjustable pitch motor pulley. Job site selected (B.H.P.) brake horsepower shall not exceed the motors nameplate horsepower rating, plus the service factor. Units shall be designed not to operate above service factor. Fan wheel shall be double-inlet type with for- ward-curved blades, dynamically balanced to operate smoothly throughout the entire range of operation. Airflow design shall be constant air volume. Bearings shall be sealed and permanently lubricated for longer life and no maintenance.

OUTDOOR (CONDENSER) FAN ASSEMBLY

The outdoor fan shall be of the direct-driven propeller type, discharge air vertically, have aluminum blades riveted to a corrosion resistant steel spider bracket and shall be dynami- cally balanced for smooth operation. The outdoor fan motor shall be totally enclosed with permanently lubricated bear- ings, internally protected against overload conditions and staged independently.

REFRIGERANT COMPONENTS

Compressor:

a. Shall be internally protected with internal high-pres- sure relief and over temperature protection.

b.Shall have internal spring isolation and sound muf- fling to minimize vibration and noise, and be exter- nally isolated on a dedicated, independent mounting.

Coils:

a. Evaporator and condenser coils shall have alumi- num plate fins mechanically bonded to seamless

42

Unitary Products Group

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Warranty DescriptionTable of Contents Product Nomenclature Product Nomenclature Johnson UNT Controller, DFS, APS, SS Drain Pan Technicoat Condenser Coil & Dirty Filter Switch Hinged Filter Door & Toolless Access Cabinet 036-21502-003-A-1105 Novar ETC-3 Controller, DFS, APS, SS Drain Pan Hinged Filter Door & Toolless Access Cabinet Features FACTORY-INSTALLED Options Unit CutawayFIELD-INSTALLED Accessories Hinged Filter DOOR/TOOLLESS Blower036-21502-003-A-1105 GAS Heat RATINGS1 Sound Power RATING1Capacity Ratings ARI 210/2401 Stage GAS Heat RatingsDM036 Cooling Capacities 3 TON DM048 Cooling Capacities 4 TON DM060 Cooling Capacities 5 TON DM072 Cooling Capacities 6 TON 31,2 036-21502-003-A-1105 036-21502-003-A-1105 036-21502-003-A-1105 Belt Drive Blower Motor and Drive Data Minimum Supply AIR CFM Static ResistancesElectric Heater CFM Limitations Voltage Heater Size Nominal KW TonsRLA LRA Voltage Motor Outlet Brkr 1 Size Tonnage Outlet Brkr 1 Size Tonnage 036-21502-003-A-1105 036-21502-003-A-1105 036-21502-003-A-1105 036-21502-003-A-1105 036-21502-003-A-1105 Physical Data Electric Heat Correction FactorsVoltage LIMITATIONS1 Typical Power Wiring Typical Field Power & Control WiringUnit Dimensions 3 6 TON COOLING/GAS Heat Front View Unit with Economizer Rainhood Minimum Clearances Hole Opening Size DIA Used forLocation Clearance Typical Applications Unit Total DimensionCenter of Gravity TONBasic Operating Weights LBSModel Size TON OptionsGuide Specifications GeneralDescription Unit Controls Manual Outdoor AIR Damper

DM 072 specifications

The York DM 072 is a high-performance packaged air conditioning unit designed for commercial and industrial applications. Engineered for efficiency and reliability, the DM 072 is part of York's broader initiative to provide advanced climate control solutions that meet the demands of modern buildings.

One of the standout features of the York DM 072 is its advanced energy efficiency. It employs the latest in variable speed technology, which allows the unit to adjust its output according to the cooling load. This capability significantly reduces energy consumption, leading to lower operational costs, and it aligns with global efforts to promote sustainable energy use.

In terms of design, the York DM 072 is built with a robust aluminum cabinet that provides excellent corrosion resistance. This is essential for units installed in harsh environments, ensuring a long lifespan and reduced maintenance needs. The compact design also allows for easy installation in tight spaces, making it a versatile choice for various building configurations.

The unit is equipped with a high-efficiency scroll compressor, which enhances its cooling capabilities while minimizing noise levels. This is particularly beneficial for commercial office buildings where noise reduction can contribute to a more comfortable working environment. Additionally, the DM 072 features a sophisticated refrigerant management system that optimizes the refrigeration cycle, ensuring consistent performance and maximizing system efficiency.

Another notable aspect of the York DM 072 is its advanced control system. With smart connectivity options, users can monitor and control the unit remotely. This feature not only improves convenience but also aids in proactive maintenance by providing real-time performance data, helping facility managers to identify and rectify issues before they escalate.

The DM 072 also incorporates an effective filtration system designed to improve indoor air quality. With multi-stage filtration, it captures dust, allergens, and other particulates, promoting a healthier environment for occupants.

With a combination of efficiency, durability, advanced technology, and environmental considerations, the York DM 072 stands out as a leading choice in the commercial HVAC market. Whether for new constructions or retrofitting existing systems, it offers reliable performance and environmental stewardship, making it a top contender among packaged air conditioning units.
Top Page Image Contents