Filter Care, Outdoor Unit Finish, Clearances

126114-UUM-E-0107

If your system is an add-on type, (installed in conjunction with a stan- dard furnace) inspect your furnace blower motor and care for it in the same way.

FILTER CARE

Inspect the air filter(s) at least once a month. If they are dirty, wash reusable filters with a mild detergent per manufacturer’s recommenda- tions. Replace disposable filters with new filters.

Install the clean filters with “air flow” arrow in the same direction as the air flow in your duct. Filters should be clean to assure maximum effi- ciency and adequate air circulation. Drapes, furniture or other obstruc- tions blocking your supply and return air grilles will also decrease efficiency.

OUTDOOR UNIT FINISH

If you wish to maintain the finish of the outdoor unit, it can be polished with car wax. It is recommended the unit be cleaned with soap and water prior to waxing.

TROUBLESHOOTING GUIDE

PROBLEM		CHECK		ACTION TO TAKE	FAULT CODE

	1.	Thermostat for proper settings.	Set thermostat to proper setting.		-

	2.	Circuit breakers and fuses.	Reset circuit breakers - Replace blown fuses.		-

No Heat	3.	Check outdoor unit for dirty coil (Cooling).	Clean coil, see “COIL CARE” section.		2

	4.	Outdoor unit for snow accumulation. (Heating).	Remove loose snow only.		3
or	4.	Outdoor unit for snow accumulation. (Heating).	Remove loose snow only.		3
or
Cooling	5.	Indoor unit for dirty filter (Heating).	Clean or replace, see “FILTER CARE” section.		2

	6.	Emergency heat light status on thermostat.	Check 1	- 5, call qualified service person.	2

		Light on = Malfunction	Check 1	- 5, call qualified service person.	-

		Light flashing = Malfunction	Check 1	- 5, call qualified service person with fault code.	-

Wet on Floor		Condensate drain and “P” trap	Remove blockage, usually mold or fungus.		-
or in Furnace		Condensate drain and “P” trap	Remove blockage, usually mold or fungus.		-
or in Furnace

CLEARANCES

The minimum clearances shown below must be maintained should any patio or yard improvements be done around the outdoor unit.

•Top 48”

•Sides 12”

•Access 24”

POWER INTERRUPTION

When ice, snow, wind storms, etc. disrupt electrical power supply to your house, proceed as follows:

Heating Season

1.Switch thermostat to emergency heat.

NOTE: There will be no heat available until power is re-established.

2.Leave on emergency heat for at least 8 hours after electrical power is re-established if the power was off more than 8 hours.

3.Switch thermostat back to heating or auto.

Cooling Season

1.Switch thermostat to OFF position.

2.Do not switch to cooling or auto until electrical power has been re- established for 8 hours if the power was off more than 8 hours.

SERVICE CALLS

There are a few instances where you can avoid unnecessary service calls. (See Troubleshooting Guide above). Some models provide fault codes. The flashing light on the system thermostat is capable of provid- ing you with time and money saving information. The fault code num- bers listed can be handled by taking the corrective action indicated. Call qualified service person if displaying fault code numbers not listed.

PARTS INFORMATION

Replacement parts are available from local contractor/dealers or the nearest distribution center.

Unitary Products Group

14 Series, 13 Series specifications

The York 13 Series and 14 Series are renowned for their advanced design and efficiency, making them standout choices in the HVAC industry. Both series are engineered to provide reliable cooling and heating solutions for residential and commercial spaces, with a focus on performance, efficiency, and comfort.

The York 13 Series, which is considered one of the most reliable options on the market, features high-efficiency compressors and environmentally friendly refrigerants. Its SEER (Seasonal Energy Efficiency Ratio) ratings typically range from 13 to 16, ensuring optimal cooling performance while keeping energy costs manageable. This series is designed with ease of maintenance in mind, featuring a compact design that allows for convenient access to internal components. One of its key technological advancements is the use of Smart Life technology, which allows users to control the unit remotely via smartphone applications, ensuring efficient operation and user-friendly management.

On the other hand, the York 14 Series takes efficiency a step further, with SEER ratings reaching up to 18. This series is equipped with advanced variable speed compressors, which adjust to the precise cooling needs of the space, thereby reducing operational energy consumption. The 14 Series also boasts enhanced sound insulation technology, which ensures quieter operation. Homeowners and business operators can appreciate these quieter systems, especially in noise-sensitive environments like classrooms and workplaces.

Both series incorporate high-quality, durable materials designed to withstand the rigors of various environmental conditions. The use of advanced heat exchangers and fan technology helps increase airflow and maintain temperature stability. Additionally, the units are designed to operate within a broad temperature range, providing reliable performance during extreme weather conditions.

Moreover, both the 13 and 14 Series come with extensive warranty options, showcasing York's commitment to quality and reliability. The combination of innovative features, advanced technologies, and dependable performance makes the York 13 Series and 14 Series excellent choices for individuals seeking energy-efficient heating and cooling solutions. With their user-friendly controls, energy-saving capabilities, and high reliability, these systems are well-equipped to meet the diverse needs of today’s consumers. Whether for residential or commercial use, the York 13 and 14 Series continue to set industry standards in HVAC efficiency and comfort.