York DJ 300, DJ 210, DJ 240 Outdoor Condenser FAN Assembly, Refrigerant Components, Unit Controls

Page 38

261660-YTG-D-0708

OUTDOOR (CONDENSER) FAN ASSEMBLY

The outdoor fans shall be of the direct-driven propeller type, discharge air vertically, have aluminum blades riveted to cor- rosion resistant steel spider brackets and shall be dynami- cally balanced for smooth operation. The 4 outdoor fan motors shall be totally enclosed with permanently lubricated bearings, internally protected against overload conditions and staged independently.

REFRIGERANT COMPONENTS

Compressors:

a.Shall be Scroll compressors internally protected with internal high-pressure relief and over temperature protection.

b.Shall have internal spring isolation and sound muf- fling to minimize vibration and noise, and be exter- nally isolated on a dedicated, independent mounting.

Coils:

a.Evaporator and condenser coils shall have alumi- num plate fins mechanically bonded to seamless internally enhanced copper tubes with all joints brazed. Special Phenolic coating shall be available as a factory option.

b.Evaporator and Condenser coils shall be of the direct expansion, draw-thru, design.

Refrigerant Circuit and Refrigerant Safety Components shall include:

a.Balance-port thermostatic expansion valve with independent circuit feed system.

b.Filter drier/strainer to eliminate any moisture or for- eign matter.

c.Accessible service gage connections on both suc- tion and discharge lines to charge, evacuate, and measure refrigerant pressure during any necessary servicing or troubleshooting, without losing charge.

d.The refrigeration system shall provide at least 15° F of sub-cooling at design conditions.

e.All models shall have two independent circuits.

f.Hot gas bypass option shall be factory-installed on compressor #1 discharge line to provide cooling in low-load applications. HGBP shall be a standard feature on VAV models and an optional feature on CV models.

UNIT CONTROLS

a.Unit shall be complete with self-contained low-volt- age control circuit protected by a resetable circuit breaker on the 24-volt transformer side.

b.Unit shall incorporate a lockout circuit which pro- vides reset capability at the space thermostat or base unit, should any of the following standard safety devices trip and shut off compressor.

c.Loss-of-charge/Low-pressure switch.

1.High-pressure switch.

2.Freeze-protection thermostat, evaporator coil. If any of the above safety devices trip, a LED (light-emitting diode) indicator shall flash a diagnostic code that indicates which safety switch has tripped.

d.Unit shall incorporate "AUTO RESET" compressor over temperature, over current protection.

e.Unit shall operate with conventional thermostat designs and have a low voltage terminal strip for easy hook-up.

f.Unit control board shall have on-board diagnostics and fault code display.

g.Standard controls shall include anti-short cycle and low voltage protection, and permit cooling operation down to 0 °F.

h.Control board shall monitor each refrigerant safety switch independently.

i.Control board shall retain last 5 fault codes in non volatile memory, which will not be lost in the event of a power loss.

GAS HEATING SECTION (DJ***N MODELS)

Shall be designed with induced draft combustion with post purge logic and energy saving direct spark ignition, redun- dant main gas valve. Ventor wheel shall be constructed of stainless steel for corrosion resistance. The heat exchanger shall be of the tubular type, constructed of T1-40 aluminized steel for corrosion resistance and allowing minimum mixed air entering temperature of 25° F. Burners shall be of the in- shot type, constructed of aluminum coated steel and contain air mixture adjustments. All gas piping shall enter the unit cabinet at a single location through either the side or curb, without any field modifications. An integrated control board shall provide timed control of evaporator fan functioning and burner ignition. Heating section shall be provided with the fol- lowing minimum protection:

a. Primary and auxiliary high-temperature limit switches.

b.Induced draft motor speed sensor.

c.Flame roll out switch (automatic reset).

d.Flame proving controls. Unit shall have two inde- pendent stages of capacity.

38

Johnson Controls Unitary Products

Image 38
Contents Warranty DescriptionTable of Contents Product Nomenclature Ton Magnum Model Number NomenclatureFeatures FACTORY-INSTALLED Options Unit CutawayJohnson Controls Unitary Products York Commercial Comfort System Yccs FIELD-INSTALLED Accessories GAS Heat Ratiings Sound Power RATING1Capacity Ratings ARI Cooling Capacities for DJ180 MBHCooling Capacities for DJ210 6500Cooling Capacities for DJ240 8000Cooling Capacities for DJ300 Altitude Correction Factors AIR Temp Altitude FeetYTG-D-0708 Volt and Standard Drive Volt Standard Drive 6000 7000 8000 9000 9400 965 980 1025 1065 1125 1170 870 900 930 950 980 995 1015 6000 7000 8000 9000 9400 7500 8750 10000 11250 12500 Static RESISTANCES1 Power Exhaust PerformanceBlower Motor and Drive Data DJ Electrical Data Without Powered Convenience Outlet Size240 DJ Electrical Data with Powered Convenience Outlet None 120.4 150 E18 13.5 37.5 Models DJ Voltage LIMITATIONS1Physical Data Supply FAN VFD WEIGHTS, in LBS Electric Heat Correction FactorsFront View Dimensions Utilities Entry Data Rear View Dimensions Unit Dimensions DJ180, 210, 240 & 300 Rainhood Minimum ClearancesUnit Center of Gravity Four and SIX Point Loads Unit Roof Curb Dimensions OCC Unit Cabinet Guide SpecificationsIndoor Evaporator FAN Assembly Unit Controls Outdoor Condenser FAN AssemblyRefrigerant Components GAS Heating Section DJ***N ModelsElectric Heating DJ***C/E Models Unit Operating CharacteristicsOther PRE-ENGINEERED Accessories Available Electrical RequirementsOther Factory Installed Options

DJ 300, DJ 240, DJ 210 specifications

York has carved a niche for itself in the world of DJ equipment, particularly with its DJ series, which includes models such as DJ 210, DJ 240, and DJ 300. Each of these models showcases unique features and technologies that cater to both aspiring and professional DJs, making them popular choices for live performances, parties, and events.

Starting with the DJ 210, this model is an ideal entry-level DJ controller designed for users who are just starting to explore the world of mixing. One of its standout features is the intuitive layout, which includes easily navigable controls and a user-friendly interface. It boasts large jog wheels that offer precise pitch bending and scratching capabilities, crucial for any DJ. Additionally, the DJ 210 comes equipped with built-in sound effects that can enhance mixes, giving users the ability to customize their performances. Compatibility with various DJ software such as Serato and Virtual DJ adds to its versatility, making it an excellent choice for beginners looking to hone their skills.

Moving on to the DJ 240, this model caters to a more intermediate audience. It builds on the features of the DJ 210 but introduces several advanced characteristics. The DJ 240 includes dual USB ports, allowing seamless plug-and-play functionality so that two DJs can share the controller easily during live sets. The enhanced sound quality and additional EQ controls give DJs more manageable sound options, enabling smoother transitions and richer audio output. Furthermore, the DJ 240 features an integrated sampler that allows users to trigger pre-loaded sound clips, making mixing more dynamic and engaging.

Finally, the DJ 300 represents the pinnacle of York's DJ offerings. This high-end model is loaded with cutting-edge technology, including responsive touch-sensitive jog wheels that provide an even more tactile mixing experience. The DJ 300 features advanced digital effects processing, offering an extensive range of effects and filters that can be applied live. Moreover, its robust construction and professional-grade faders ensure seamless operation in high-energy environments. With multiple outputs for various audio configurations, the DJ 300 is designed for the seasoned performer who demands flexibility and precision in their setup.

Overall, York's DJ series—encompassing the DJ 210, DJ 240, and DJ 300—caters to a diverse range of DJ needs, from novice to professional. Whether you are just starting your DJ journey or are a seasoned veteran, there is a York DJ model tailored to your requirements, each boasting features and technologies that elevate the art of music mixing.