York DJ 036, DJ 048, DJ 060 warranty Guide Specifications, General, Description

Page 43

036-21687-002-A-1105

GUIDE SPECIFICATIONS

GENERAL

Units shall be manufactured by York International Unitary Products Group in an ISO 9001 certified facility.

York's Sunline Magnum™ units are convertible single pack- age units. Although the units are primarily designed for curb mounting on a roof, they can also be slab-mounted at ground level or set on steel beams above a finished roof. Cooling only, cooling with gas heat and cooling with electric heat models are available with a wide variety of factory-mounted options and field-installed accessories to make them suitable for almost every application. All units are self-contained and assembled on full perimeter base rails with holes in the four corners for overhead rigging. Every unit is completely piped, wired, charged and tested at the factory to simplify the field installation and to provide years of dependable operation. All models (including those with an economizer) are suitable for either bottom or horizontal duct connections. Models with power exhaust are suitable for bottom duct connections only. For bottom duct, remove the sheet metal panels from the supply and return air openings through the base of the unit. For horizontal duct, remove the supply and return air panels on the rear of the unit.

All non-Scroll compressors include crankcase heaters and all compressors have internal pressure relief. Every refrigerant circuit includes a liquid line filter-drier, a discharge line high pressure switch and a suction line with a freezestat and low pressure/loss of charge switch.The unit control circuit includes a 75 VA transformer, a 24-volt circuit breaker and a relay board with a compressor lockout circuit, a terminal strip for thermostat wiring, plus an additional set of pin connectors to simplify the interface of additional field controls. All models are CSA listed. All models include a 1-year limited warranty on the complete unit. Compressors and electric heater ele- ments carry a 5-year warranty. Aluminized steel and Stainless steel tubular heat exchangers carry a 10-year warranty.

DESCRIPTION

Units shall be factory-assembled, single packaged, Electric Cooling/Gas Heat, Electric Cooling/Optional Electric Heat and designed for outdoor mounted installation.

The 3 ton, 4 ton and 5 ton units shall have minimum SEER rating of 13. They shall have built-in field convertible duct connections for down discharge supply/return or horizontal discharge supply/return, and be available with factory installed options or field installed accessories. The units shall be factory wired, piped, charged with R-22 refrigerant and factory tested prior to shipment. All unit wiring shall be both numbered and color coded. All units the cooling performance shall be rated in accordance with DOE and ARI test proce- dures. Units shall be CSA listed, classified to ANSI Z21.47, UL 1995/CSA No. 236 standards.

Coils:

a. Evaporator and condenser coils shall have alumi-

UNIT CABINET

Unit cabinet shall be constructed of G90 galvanized steel, with exterior surfaces coated with a non-chalking, powdered paint finish, certified at 1000 hours salt spray test per ASTMB117 standards. Indoor blower section shall be insu- lated with a minimum 1/2” thick insulation, coated on the air- side. Aluminum foil faced insulation shall be used in the furnace compartment and be fastened with ridged fasteners to prevent insulation from entering the air stream. Cabinet panels shall be “large” size, easily removable for servicing and maintenance. Full perimeter base rails shall be provided to assure reliable transit of equipment, overhead rigging and proper sealing on roof curb applications. Disposable 1" filters shall be furnished and be accessible through a removable access door, sealed airtight. Units filter track shall be designed to accommodate either 1" or 2" filters. Fan perfor- mance measuring ports shall be provided on the outside of the cabinet to allow accurate air measurements of evaporator fan performance without removing panels or creating air by- pass of the coils. Condensate pan shall be internally sloped and conform to ASHRAE 62-89 self-draining standards. Con- densate connection shall be a minimum of 3/4” I.D. female and be a ridged mount connection.

INDOOR (EVAPORATOR) FAN ASSEMBLY

The indoor fan shall be a factory installed belt drive assembly that includes an adjustable pitch motor pulley. Job site selected (B.H.P.) brake horsepower shall not exceed the motors nameplate horsepower rating, plus the service factor. Units shall be designed not to operate above service factor. Fan wheel shall be double-inlet type with forward-curved blades, dynamically balanced to operate smoothly throughout the entire range of operation. Airflow design shall be constant air volume. Bearings shall be sealed and permanently lubri- cated for longer life and no maintenance.

OUTDOOR (CONDENSER) FAN ASSEMBLY

The outdoor fan shall be of the direct-driven propeller type, discharge air vertically, have aluminum blades riveted to a corrosion resistant steel spider bracket and shall be dynami- cally balanced for smooth operation. The outdoor fan motor shall be totally enclosed with permanently lubricated bear- ings, internally protected against overload conditions and staged independently.

REFRIGERANT COMPONENTS

Compressor:

a. Shall be internally protected with internal high-pres- sure relief and over temperature protection.

b.Shall have internal spring isolation and sound muf- fling to minimize vibration and noise, and be exter- nally isolated on a dedicated, independent mounting.

num plate fins mechanically bonded to seamless internally enhanced copper tubes with all joints

Unitary Products Group

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents Description WarrantyTable of Contents $LUIORZ Product NomenclatureProduct Nomenclature Johnson UNT Controller, DFS, APS, SS Drain Pan Technicoat Condenser Coil & Dirty Filter Switch Hinged Filter Door & Toolless Access Cabinet 036-21687-002-A-1105 Novar ETC-3 Controller, DFS, APS, SS Drain Pan Hinged Filter Door & Toolless Access Cabinet Features Unit Cutaway FACTORY-INSTALLED OptionsFIELD-INSTALLED Accessories EER2 SEER3 Sound Model MBH CFM Rating Capacity Ratings ARI 210/2401GAS Heat RATINGS1 Stage GAS Heat RatingsUnit Description / Model DJ036 Indoor Sound Power Levels Horizontal Ducted InletDJ036 Indoor Sound Power Levels Horizontal Ducted Discharge ConfigurationDJ036 Indoor Sound Power Levels Vertical Ducted Discharge DJ036 Indoor Sound Power Levels Vertical Ducted InletDJ048 Indoor Sound Power Levels Horizontal Ducted Discharge DJ048 Indoor Sound Power Levels Horizontal Ducted InletDJ048 Indoor Sound Power Levels Vertical Ducted Discharge DJ048 Indoor Sound Power Levels Vertical Ducted InletDJ060 Indoor Sound Power Levels Horizontal Ducted Discharge DJ060 Indoor Sound Power Levels Horizontal Ducted InletDJ060 Indoor Sound Power Levels Vertical Ducted Discharge DJ060 Indoor Sound Power Levels Vertical Ducted InletMBH DJ036 Cooling Capacities 3 TONDJ048 Cooling Capacities 4 TON DJ060 Cooling Capacities 5 TON BHP AIR Available External Static Pressure IWG1 FlowRPM BHP RPM720 364 764 404 806 443 831 567 874 602 1000 833 564 879 605 1200 876 632 918 667 1300 1000 862 453 901 498 RESISTANCE, IWG Description Belt Drive Blower Motor and Drive DataStatic Resistances Electric Heater CFM LimitationsDJ036 Tonnage RLA LRA Motor Outlet 036-21687-002-A-1105 Tonnage Voltage RLA LRA Motor Outlet Electric Heat Correction Factors Physical DataVoltage LIMITATIONS1 Typical Field Power & Control Wiring Typical Power WiringUnit Dimensions 3 5 TON COOLING/GAS Heat Front View Unit with Economizer Rainhood Hole Opening Size DIA Used for Minimum ClearancesLocation Clearance Typical Applications Center of Gravity DimensionUnit Total Unit Operating Weights LBSModel Size TON BasicGeneral Guide SpecificationsDescription Electric Heating Section Unit Operating CharacteristicsUnit Controls GAS Heating Section Single or 2 StageElectric Heaters Other PRE-ENGINEERED Accessories AvailableManual Outdoor AIR Damper 036-21687-002-A-1105 036-21687-002-A-1105 036-21687-002-A-1105

DJ 060, DJ 036, DJ 048 specifications

The York DJ series, which includes models DJ 036, DJ 060, and DJ 048, has become a staple in the DJ community, known for their impressive features, robust technologies, and user-friendly characteristics. These models are designed to meet the diverse needs of DJs, from beginners to seasoned professionals, offering a range of functionalities that cater to different performance styles.

The York DJ 036 is particularly favored for its portability and user-centric design. Weighing in at a lightweight, this model is perfect for mobile DJs who need to set up quickly and efficiently. The DJ 036 boasts a built-in mixer with multiple channels, allowing for seamless transitions between tracks. Its intuitive layout makes it easy for users to navigate through various controls, making it ideal for those new to DJing. Additionally, its compatibility with various audio inputs ensures that DJs can connect multiple devices effortlessly, enhancing their creative possibilities.

Moving to the York DJ 060, this model takes things a step further with enhanced functionality and sound quality. The DJ 060 features advanced digital signal processing technology, which ensures crystal-clear audio playback and eliminates unwanted noise. Its loop and cue functions provide DJs with greater control over their sets, allowing for creative mixing and live remixing on the fly. Furthermore, the DJ 060 includes an integrated LED display that provides vital information such as track time and tempo, enabling DJs to keep track of their performance without missing a beat.

Lastly, the York DJ 048 is engineered for those who require a more comprehensive setup. This model integrates a higher number of channels and effects processors, making it perfect for complex performances. The DJ 048 supports MIDI compatibility, enabling DJs to connect various controllers and software, expanding their creative toolbox. The inclusion of high-quality sound outputs ensures that performances are not only dynamic but also rich in quality.

In summary, the York DJ series, particularly the DJ 036, DJ 060, and DJ 048, delivers a compelling combination of portability, advanced technology, and user-friendly features. Each model caters to different levels of expertise and performance requirements, making York a trusted choice among DJs looking for reliable and innovative equipment. Whether for casual gatherings or professional gigs, these models are equipped to elevate any DJ’s performance.
Top Page Image Contents