HP 2311cm/2311f/2311x, 2211f/2211x, 2511x, 2011x/2011s manual Identifying Monitor Conditions

Page 30

Icon

Main Menu Options

Sub-menu Options

Description

 

 

 

 

 

 

Auto-Switch Source

Turns the automatic video signal input to

 

 

 

On or Off on the system. The factory

 

 

 

default is On.

 

 

 

 

 

Exit

 

Exits the OSD menu screen.

 

 

 

 

Identifying Monitor Conditions

Special messages appear on the monitor screen for the following monitor conditions:

Monitor Status — When the monitor is powered on or when the input source signal is changed, a Monitor Status message is displayed for five seconds. The message shows which input is the current active signal, the status of the auto-switch source setting (On or Off), the default source signal, the current preset display resolution, and the recommended preset display resolution.

Input Signal Out of Range — Indicates the monitor does not support the input signal on the video card, because its resolution or refresh rate is set higher than the monitor supports.

Change your video card settings to a lower resolution or refresh rate. Restart your computer for the new settings to take effect.

Power Button Lockout — Indicates the power button is locked. If the power button is locked, the warning message Power Button Lockout appears.

If the power button is locked, press and hold the power button for 10 seconds to unlock the power button function.

If the power button is unlocked, press and hold the power button for 10 seconds to lock out the power button function.

Monitor Going to Sleep — Indicates the screen display is entering a sleep mode.

Check Video Cable — Indicates a video input cable is not properly connected to the computer or monitor.

OSD Lockout — The OSD can be enabled or disabled by pressing and holding the Menu button on the front panel for 10 seconds. If the OSD is locked, the warning message OSD Lockout appears for 10 seconds.

If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.

If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.

Dynamic Contrast Ratio ON – Indicates that DCR is turned on.

Dynamic Contrast Ratio OFF – Indicates that DCR has been turned off in the OSD or was automatically turned off after changes were made to Brightness or Quick View in the OSD.

No Input Signal — Indicates the monitor is not receiving a video signal from the computer on the monitor video input connector. Check to see if the computer or input signal source is off or in the power-saver mode.

24 Chapter 4 Operating the Monitor

ENWW

Image 30
Contents User Guide Second Edition January Document Part Number About This Guide Iv About This Guide Table of contents Appendix a Troubleshooting Product Features LCD MonitorsEnww Safety and Maintenance Guidelines Important Safety InformationSafety Precautions Maintenance GuidelinesCleaning the Monitor Shipping the MonitorSetting Up the Monitor Unpacking the MonitorAssembling the Monitor 2Inserting the Monitor Panel Connecting Monitor Cables Connecting the VGA Video CableConnecting the DVI-D Video Cable Select Models Connecting the Hdmi Cable Select ModelsConnecting the Power Cord Getting Hdmi Sound6Connecting the Power Cord Installing the Cable Management Clip Turning on the MonitorSelecting Video Input Connectors Adjusting The TiltConnecting External Speakers and Audio Cable Select Models Wall Mounting the Monitor Panel Enww Installing Drivers Operating the MonitorCD Software and Utilities Front-Panel Controls Button Icon DescriptionUsing the On-Screen Display OSD Icon Main Menu Options Sub-menu Options DescriptionEnww Power-Saver Feature on Enww VGA Identifying Monitor Conditions Power-Saver Feature Troubleshooting Solving Common ProblemsProblem Solution ProblemSolution Have the following information available when you call Locating the Rating LabelSpecifications Technical SpecificationsTable B-12011x/2011s Specifications HP LCD MonitorsTable B-22211f/2211x Specifications Table B-32311cm/2311f/2311x SpecificationsTable B-42511x Specifications Table B-52711x Specifications Preset Video Modes Table B-62011x/2011s Factory Preset Video Input ModesEntering User Modes Power AdaptersTable B-9Power Adapters Manufacturer Model NumberLCD Monitor Quality and Pixel Policy Modifications Agency Regulatory NoticesFederal Communications Commission Notice CablesCanadian Notice Avis CanadienEuropean Union Regulatory Notice Japanese Notice Korean Notice Power Cord Set Requirements German Ergonomics NoticeJapanese Power Cord Requirements Product Environmental NoticesEnergy Star Qualification Enww Turkey EEE Regulation
Related manuals
Manual 2 pages 51.04 Kb