HP CA-340 manual Using the Self-timer & Burst, 10 sec, Double

Page 35

Using the Self-timer & Burst

Use the self-timer to set a delay from the time the shutter button is pressed to the time the image is shot. Use the burst to record continuous still images shooting.

Turn the power on, and set the camera

to the REC mode (	page 13).
Open the REC menu (	page 16).

Use or button to select [Drive mode] from the REC menu.

Change the setting.

Press or to select a drive mode, then press the OK button.

Off:

Record a single image.

2 sec.:

The shutter release will be delay for 2 seconds.

10 sec.:

The shutter release will be delay for 10 seconds.

Double:

Record two images in a shot after pressing the shutter release button 10 and 12 seconds.

Burst:

Keep pressing the shutter button fully to take continuous shooting. Release the shutter button to stop shooting.

Press shutter button to take a picture.

Tips

When using the self-timer function, be sure to use a tripod or place the digital camera on a level, stable surface.

Image 35

Contents HP CA340 „ FCC Compliance and Advisory PrecautionsContents Iii Using This Menu Unpacking Parts of the Camera Four-way ControlPage Inserting the Batteries Low Battery IndicatorAbout Battery Type About Camera Memory Inserting the Memory CardInsert the card TipsSetting the Date & Time Setting the Display Language / Date & TimeSetting the Display Language Apply the setting REC mode Using the LCD MonitorDpof Playback modeChanging the LCD Status REC modePlayback mode Power Saving Function Turning the Power On and OffPress the Power button to turn on Camera in the REC mode Press the Power button again to turn the power offSet the camera to the REC mode Launch the mode palette Changing the ModeSwitching between REC mode and Playback mode Selecting the REC modeCapture the most brilliant smile of characters Launch the ASM mode Selecting the ASM modeSet the camera to the REC mode Select an item Using the MenusChange the setting REC menuREC menu list Movie Setup menu Off Setup menu listReset BeepOff / On Computer / PrinterTake a picture Recording Still ImagesHalf press the shutter button to focus the image To activate smile capture Using smile capture ModeTo activate Intelligent Scene Using Intelligent Scene ModeTips To activate Blink Detection Using Blink Detection ModeFace Tracking Off / On Using the Q modeStabilizer Off / On Quality Values Setting Image Size and QualityResolution Values Press shutter button to take a picture Tips Using the Zoom FunctionUsing the Flash Infinity Using the MacroPan Focus Burst Using the Self-timer & Burst10 sec DoubleUsing the Shutter Priority Using the Aperture PriorityUsing the Manual Exposure Finish recording Recording Movie ClipsStart recording Press the shutter button again to end recording Setting the Movie SizeRecording Audio Clips Movie Size and Frame RatePlaying Back a Voice Memo Recording a Voice MemoOpen the Playback menu Press the OK button to start recording for 30 secondsSetting the White Balance Setting the MeteringSetting the Highlight Setting the ISOSetting the Exposure Setting the AEBSetting Date Stamp Setting the SharpnessSetting the Photo Edit Setting Photo Frame Setting StabilizerSetting Face tracking Playing Back Movie Clips Turn the power on, and set Camera to the Playback ModePlaying Back Images Press the four-way control orSave the image Magnifying & Trimming Still ImagesMagnify the image Trim the imagePlaying the slide show Change the slide show settingsViewing in Thumbnail Playing a Slide ShowDeleting a Single File Deleting FilesDelete images Deleting Multiple FilesPress or to select Select, and then press the OK button Select multiple imagesPress the OK button to protect all images Protecting a Single FileProtecting All Files Press or to select Lock all, and then press the OK buttonProtect images Protecting Multiple FilesChanging the Image Size Editing ImagesRotating Still Images Press the OK button to rotate the imageChoosing the Image with Photo Frame Changing the Image with EffectsPress or to select Single, then press the OK button Copying the FilesPrint the date stamp out Setting the DpofOr to select Single, then press the OK button Choosing a Startup Image Connecting the Camera to a Computer with the USB Cable Connecting the Camera to a PCUsing the Card Reader File Naming About the Folder & File NameFolder Structure Problem Cause Solution TroubleshootingNtsc / PAL SpecificationsPage Function Available List Intelligent Scene O O O O O ” O O O O O O O O O O O O O O O O Not available Orswitchpower off Disable function Photography Terms and Definitions Exposure index Digital still cameraDynamic range Exif/JPEGGetting Help 7525C00052B