Operation, HOW Your Furnace Works | United States Stove 6100

Operation

Do not operate your furnace with the viewing door open. The auger will not feed fuel under these circumstances and a safety concern may arise from sparks or fumes entering the room.

A working smoke detector must be installed in the same room as this product.

Hopper Lid must be closed during operation. The auger will not feed fuel if the lid is open.

HOW YOUR FURNACE WORKS

Your Multi-Fuel Furnace utilizes a inclined auger fuel feed system that is operated by a microprocessor controlled digital circuit board. The digital circuit board allows the inclined auger fuel feed system to run in a timer-based, non-continuous cycle; this cycling allows the auger to run for a predetermined period of seconds. The auger pushes fuel up a chute located at the front/bottom of the hopper which in turn falls through another chute into the burnpot . As fuel enters the burn pot, outside air is drawn across the fuel and heated during the combustion process. This heated combustion air is then pulled through the heat exchanger by the Draft Fan, where it is used to heat air that is drawn into the heat exchanger system by the distribution blower.

Because a forced draft pressure is required for the combustion process inside your furnace, it is extremely important that the exhaust system be properly installed and maintained. And, that when operating your furnace, you make sure that the viewing door is properly sealed.

Your furnace’s heat output can vary from Hi to Low by adjusting the settings on the control panel (located on the lower left-hand side of the furnace). The “HEAT RANGE” setting will vary the auger systems feed rate (i.e. fuel to combustion air ratio) and has three settings, low / medium / high. This is indicated by displaying a Hr-1 thru Hr-3 under Heat Range.

Your furnace has two distribution “Room Air” blowers. Fan “A” located on the left side of the unit, same side as the (PCB) Printed Circuit Board, will come on when flue gas temperatures reaches the (POT) Programmable Operating Temperature (200°F) preset on the control board. During shutdown, Fan “A” will remain on until the operating temperature reaches the preset temp. 110°F. Fan “B” will come on when plenum temperatures reach the preset (PPT) Programmable Plenum Temperatures (95°F). The fan will remain on until the plenum temperature drops 5°F below the programmed duct temp.

Your furnace can run efficiently over extended periods of time and at different heat output levels as long as the air/fuel mixture is correct and the fuel supply is uninterrupted along with proper cleaning and when maintenance is performed.

DAMPER CONTROL ADJUSTMENT

Your furnace has an adjustable intake damper located behind the Backdraft Assembly just under the Feed Door. This damper can be adjusted for fine tunning fuels to burn at optimum performance and can help with efficiency when burning inconsistant fuels. When burning corn, it is suggested that the damper position be on Medium to HI. When burning wood pellets, it is suggested that the damper position be on low to medium. These conditions will vary with your type of fuel.

USSC

6100 specifications

The United States Stove 6100 is a highly efficient and versatile wood-burning stove designed for both performance and aesthetics. Ideal for homeowners looking to add a touch of rustic charm while ensuring optimal heating capabilities, this model stands out in the crowded market of heating appliances.

One of the main features of the US Stove 6100 is its impressive heating capacity. It can heat areas up to 2,000 square feet, making it suitable for both large living spaces and smaller cabins. This stove has a firebox that can accommodate logs up to 20 inches long, allowing for longer burn times and reduced frequency of reloading. Its large windowed door provides an attractive view of the fire, enhancing the ambiance of any room.

The 6100 incorporates advanced combustion technology, which ensures higher efficiency and lower emissions. The stove is designed with secondary combustion features that maximize heat output while minimizing smoke and particulate emissions. This is particularly important in today's environmentally conscious market, where consumers are seeking cleaner options for heating their homes. The 6100’s efficiency can help reduce heating costs and lessen the environmental impact of wood heating.

Another highlight of the US Stove 6100 is its durable construction. Built from high-quality materials, the stove is designed to withstand high temperatures and the rigors of daily use. The cast iron body not only enhances its longevity but also provides excellent heat retention, further improving efficiency. The internal components are also designed to facilitate easy maintenance, with features that make cleaning the stove a hassle-free experience.

The stove is equipped with a straightforward air control system that allows users to adjust the burn rate easily. This feature enables individuals to maintain the desired temperature and burn efficiency, ensuring that the stove operates according to specific heating needs. Additionally, its mobile home approved design makes it versatile enough for various living situations, from traditional homes to mobile units.

In summary, the United States Stove 6100 combines functionality, efficiency, and style, making it a worthy investment for those looking to enhance their heating solution. With its substantial heating capacity, advanced combustion technology, and durable construction, the 6100 promises to deliver both comfort and aesthetic appeal, positioning it as a top choice among wood-burning stoves.