Operating Notes

2.NEVER completely cover the live fire with fresh coal. Always leave a generous area of burning coal at the top of the fire and at the rear.

3.Always keep the ash pit clean.

✓If the fire goes out or does not hold overnight, look for:

1.Poor draft.

2.Incorrect damper settings.

3.Improper firing methods for coal being used.

4.More combustion air needed.

5.Coal not sized to the furnace. We recommend 1" to 3" diameter pieces of coal.

6.Ashes, if allowed to accumulate in the ash pit, will not allow the passage of required air for combustion. Keep ash pit clean.

7.This furnace is not to be used with an automatic stoker unless so certified.

Do not over draft the furnace! It is designed to operate at .06 inches of water column and must be set with a draft gauge to maintain a steady draft. (Barometric Damper recommended.)

Do not allow ashes to build up higher than 2" above grates.

Be extremely careful when removing furnace ash pan; it can get very hot.

With new steel, there is a small amount of oil or dirt on the metal. You may smell an odor. This is normal during the first operation. You may want to assemble the furnace out of doors and build a small fire in it to "burn off" this dirt and oil before installing the unit.

The furnace is designed to burn air dried wood and coal at a predetermined firing rate. Over firing could result in damage to the heat exchanger and cause dangerous operation. Over firing occurs when the ash door is left open during operation or a highly volatile fuel, i.e. large amounts of small kindling, is used.

When tending the firebox always pull the baffle slide rod out prior to opening load door. Open load door slowly to avoid a "flash back". After closing load door, push the baffle slide rod to the rear.

Equip your home with fire extinguishers and smoke detectors appropriately located.

Inspect air filters regularly. The air filter in the filter box should be changed at least every 30 days.

Oil motor on forced air draft every 90 days with a few drops of 30 wt. oil.

The distribution blower motor motor may be one of two types. If the motor has sealed bearings, no oiling is required.

If the motor is equipped with fill holes, the motor should be oiled every 90 days with several drops of 30 wt. oil.

Check the fit on the load door. It must fit tightly. If it does not, check for deterioration or wear of the ceramic rope seal. Replace defective seals.

Inspect and clean your chimney and stove pipe regularly.

In event of chimney fire, shut all draft controls and call your fire department immediately. Alert everyone in the house. If the fire is still burning vigorously, throw baking soda into firebox or discharge a fire extinguisher into the firebox. After chimney fire is over, completely inspect system for damage before further use.

Slow fires: It is not recommended burning the U.S. Stove

furnace any more than necessary early in the fall and late spring, as you cannot keep the firebox hot enough (without overheating your home) to burn gases. Slow fires can cause excessive creosote build-up in smoke pipe, chimney and firebox.

Wood should be placed directly onto the cast iron shaker grate of the U.S. Stove furnace. Do not use additional grates and/or irons.

In the event of a power failure, you may operate the 1600/1800 furnace provided the following instructions are followed:

1.Any air filter should be removed.

2.If the motorized natural draft is used, the draft cap is to be set at a 1/2 inch opening. If the forced air draft is used, the damper on the built-in draft regulator will automatically open to the preset factory spacing.

3.Do not burn garbage, plastics, gasoline, drain oil or other flammable liquids. Plastics, when burned, form hydrofluo- ric and hydrochloric acids which will damage and destroy your furnace pipe and chimney. The burning of trash or oil can result in an extremely hot fire and is sometimes a cause of chimney fires.

NEVER BURN GREEN WOOD OR TIRES.

Do not store fuel or other combustible material within marked installation clearances.

NOTE: For further information on using your furnace safely, obtain a copy of the National Fire Protection Association publi- cation "Using Coal and Wood Stoves Safely." NFPA NO. NW-8- 1974. The address of the NFPA is 470 Atlantic Ave., Boston, Massachusetts 02210.

THIS IS A WOOD AND COAL

BURNING FURNACE AND SHOULD NOT BE ALTERED

IN ANY WAY!

1600, 1800 specifications

The United States Stove Company is known for producing high-quality, efficient wood and coal stoves made for both residential and commercial applications. Among their notable models are the 1600 and 1800 series, both of which provide reliable heating solutions with a blend of traditional craftsmanship and modern technology.

The United States Stove 1600 model is designed for versatility, making it ideal for a variety of spaces, including homes, cabins, and workshops. It features a sturdy cast iron construction, contributing to its durability and ability to retain heat effectively. The 1600 is equipped with a large firebox that accommodates larger logs, allowing for extended burn times and less frequent loading. One of its main features is an air wash system that helps keep the glass door clean, providing a clear view of the fire while enhancing the stove's efficiency.

On the other hand, the United States Stove 1800 model typically offers a larger heating capacity compared to the 1600, making it suitable for bigger rooms or open floor plans. This model also boasts a robust design, often made from heavy-duty steel, which not only enhances its longevity but also provides excellent heat retention. The 1800 series may come with advanced features such as a secondary combustion system, promoting cleaner burning and improved efficiency by maximizing heat output while reducing smoke emissions.

Both models feature easy-to-use mechanical controls for regulating airflow, allowing users to adjust the fire's intensity according to their heating needs. Additionally, they are designed to be compatible with various flue venting systems, providing flexibility in installation options.

Safety is a paramount concern in both the 1600 and 1800 models, with built-in safeguards such as a thermal protective barrier and an external ash door for easy cleaning and maintenance.

Overall, the United States Stove 1600 and 1800 models embody a commitment to quality craftsmanship, efficiency, and user-friendly designs, making them excellent choices for anyone in search of reliable heating solutions in their living or working spaces. With their combination of traditional design elements and modern combustion technologies, these stoves stand out in the competitive market of heating appliances.