United States Stove 1600 Speed Blower Adjustment, Initial Factory Setting for 3 Speed Operation

Page 23

3-SPEED BLOWER ADJUSTMENT

The control center is equipped with three adjustments that allow you to select the temperature at which the blower starts operating and automatically switches from one speed to the next.

With the three controls you can set the blower for single (high speed operation), two speed operation, or three speed operation.

The High-Only setting is usually recommended for larger structures where the maximum air flow is required to achieve efficient, uniform heating. (Improper adjustment can cause undesirable cycling.)

The two or three speed settings are more applicable to smaller or medium sized structures and generally make more efficient use of the available heat. Because the blower speeds can be set to automatically change as the plenum temperature increases or decreases, the heat output can be maintained at a more uniform level throughout the cycle of the fire.

The temperature range shown on each control corresponds to the air temperature as measured at the furnace plenum.

INITIAL FACTORY SETTING FOR 3 SPEED OPERATION.

(For any other blower setting see chart)

OPTIONAL

BLOWER

ADJUSTMENTS

LOW 1

MED 2

HIGH 3

USE SMALL SCREWDRIVER (SUPPLIED)

TO MAKE FURTHER ADJUSTMENTS

NOTE: BLOWER MOTOR CFM'S FOR THE 1600/1800 ARE: BLUE-1250 CFM

BLACK-1400 CFM

RED-1100 CFM

Refer to the following chart to select the blower speed options.

BLOWER OPERATION

CONTROL SETTING

 

 

 

 

One Speed (HIGH)

 

1

Turn to temperature

 

 

 

where you wish

All 3 board wires connected to

 

 

blower to start.

high speed wire of blower. Tape

 

 

 

off low and medium wires to

 

2

Set at 150°

avoid accidental shorting.

 

3

Set at 150°

 

 

 

 

Two Speed

 

1

Turn to temperature

(MEDIUM AND HIGH)

 

 

where you wish

Connect low speed board wire to

 

 

blower to start.

 

 

 

medium speed blower wire. Connect

2

Set at least 5°

medium and high speed board wires

 

higher than Control 1.

to high speed blower wire. Tape off

 

 

 

low speed blower wire to avoid

 

3

Set at 150°

accidental shorting.

 

 

 

 

 

 

 

Three Speed

 

1

Turn to temperature

(LOW,MEDIUM,

 

 

where you wish

AND HIGH)

 

 

blower to start.

 

 

2

Set at least 5°

 

 

 

higher than Control 1.

 

 

3

Set at least 5°

 

 

 

higher than Control 2.

 

 

 

(Initial factory setting:

 

 

 

Control 1 - 110°

 

 

 

Control 2 - 120°

 

 

 

Control 3 - 140°

 

 

 

 

If you find the air from the heat registers is too cool, turn Control 1 to a higher temperature setting. The setting of Control 3 for two speed operation and Controls 2 and 3 for three speed operation may also be adjusted up or down to maintain a more constant temperature output.

3 Speed Distribution Blower Operation

●when thermostat calls for heat: L-M-H, H-M-L

●when thermostat isn't calling forhear: H, H-M-L

21

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Model 1600 United States Stove CompanyTable of Contents Chimney Requirements IntroductionLocating Your Furnace ClearancesType of Flue Required Connection Clearance Smoke Pipe InstallationCreosote Formation and Need For Removal Important Information for ALL Smoke Pipes Installation ExamplesConnecting HOT AIR Duct to Furnace Dampers on Stove PipesReturn AIR is Very Important Installation NO.1 Installation noModel 1600 6 Bricks on Each Side Parts ListOPENINGS, They are AS Follows Door Handle Installation Fuel & ASH Door Latch InstallationModels 1600 and 1800 have Been Equipped with Different PlenumSmoke Chamber Brick Installation PRE-INSTALLED AT FactoryFirebox Forced AIR Draft Shipped with Unit Optional Motorized Natural DraftModels 1600 Draft Wiring Diagram Electrical InstallationWiring Diagram Testing Testing and Operating ProceduresOperating Notes Solution Trouble Shooting and Problem SolvingBoth Parts ListModel 1600/1800 Description PART# Model Blower Kit #C60471 1400CFM Blower Kit #C6137M 1800CFM Models 1600 Fan Limit Kit #C68399PRE-ASSEMBLED AT Factory Optional KIT Motorized Natural Draft Parts ListModel 1600/1800 KIT #69189 Forced AIR Draft Parts ListPRE-ASSEMBLED AT Factory Optional Electronic Control System Installation InstructionsElectronic Control Center Wiring InstructionsOptional Speed Blower AdjustmentInitial Factory Setting for 3 Speed Operation Blower Operation Control SettingHeating Option Wiring Diagrams for Electronic Control SystemStandard Wire AIR Conditioning Option Wiring DiagramsDiagram #3 Diagram #4Installing Domestic HOT Water Coil Installation of Optional EquipmentInstalling Back Draft Damper 20 x 20 x 1 Filter Required Filter BOX Option Model 1600Either Side AT this Point Deluxe Filter BOX KIT #C61999Page Page HOW to Order Repair Parts

1600, 1800 specifications

The United States Stove Company is known for producing high-quality, efficient wood and coal stoves made for both residential and commercial applications. Among their notable models are the 1600 and 1800 series, both of which provide reliable heating solutions with a blend of traditional craftsmanship and modern technology.

The United States Stove 1600 model is designed for versatility, making it ideal for a variety of spaces, including homes, cabins, and workshops. It features a sturdy cast iron construction, contributing to its durability and ability to retain heat effectively. The 1600 is equipped with a large firebox that accommodates larger logs, allowing for extended burn times and less frequent loading. One of its main features is an air wash system that helps keep the glass door clean, providing a clear view of the fire while enhancing the stove's efficiency.

On the other hand, the United States Stove 1800 model typically offers a larger heating capacity compared to the 1600, making it suitable for bigger rooms or open floor plans. This model also boasts a robust design, often made from heavy-duty steel, which not only enhances its longevity but also provides excellent heat retention. The 1800 series may come with advanced features such as a secondary combustion system, promoting cleaner burning and improved efficiency by maximizing heat output while reducing smoke emissions.

Both models feature easy-to-use mechanical controls for regulating airflow, allowing users to adjust the fire's intensity according to their heating needs. Additionally, they are designed to be compatible with various flue venting systems, providing flexibility in installation options.

Safety is a paramount concern in both the 1600 and 1800 models, with built-in safeguards such as a thermal protective barrier and an external ash door for easy cleaning and maintenance.

Overall, the United States Stove 1600 and 1800 models embody a commitment to quality craftsmanship, efficiency, and user-friendly designs, making them excellent choices for anyone in search of reliable heating solutions in their living or working spaces. With their combination of traditional design elements and modern combustion technologies, these stoves stand out in the competitive market of heating appliances.
Top Page Image Contents