United States Stove 3000 (L) instruction manual Combustible Wall Chimney Connector Pass-Throughs

Page 14

Combustible Wall Chimney Connector Pass-Throughs

Method A. 12” (304.8 mm) Clearance to Combustible Wall Mem- ber: Using a minimum thickness 3.5” (89 mm) brick and a 5/8” (15.9 mm) minimum wall thickness clay liner, construct a wall pass- through. The clay liner must conform to ASTM C315 (Standard Specification for Clay Fire Linings) or its equivalent. Keep a mini- mum of 12” (304.8 mm) of brick masonry between the clay liner and wall combustibles. The clay liner shall run from the brick masonry outer surface to the inner surface of the chimney flue liner but not past the inner surface. Firmly grout or cement the clay liner in place to the chimney flue liner.

Method B. 9” (228.6 mm) Clearance to Combustible Wall Member: Using a 6” (152.4 mm) inside diameter, listed, factory-built Solid- Pak chimney section with insulation of 1” (25.4 mm) or more, build a wall pass-through with a minimum 9” (228.6 mm) air space be- tween the outer wall of the chimney length and wall combustibles. Use sheet metal supports fastened securely to wall surfaces on all sides, to maintain the 9” (228.6 mm) air space. When fastening supports to chimney length, do not penetrate the chimney liner (the inside wall of the Solid-Pak chimney). The inner end of the Solid- Pak chimney section shall be flush with the inside of the masonry chimney flue, and sealed with a non-water soluble refractory ce- ment. Use this cement to also seal to the brick masonry penetra- tion.

Method C. 6” (152.4 mm) Clearance to Combustible Wall Member: Starting with a minimum 24 gage (.024” [.61 mm]) 6” (152.4 mm) metal chimney connector, and a minimum 24 gage ventilated wall thimble which has two air channels of 1” (25.4 mm) each, construct a wall pass-through. There shall be a minimum 6” (152.4) mm sep- aration area containing fiberglass insulation, from the outer surface of the wall thimble to wall combustibles. Support the wall thimble, and cover its opening with a 24-gage minimum sheet metal sup- port. Maintain the 6” (152.4 mm) space. There should also be a support sized to fit and hold the metal chimney connector. See that the supports are fastened securely to wall surfaces on all sides. Make sure fasteners used to secure the metal chimney connector do not penetrate chimney flue liner.

Method D. 2” (50.8 mm) Clearance to Combustible Wall Mem- ber: Start with a solid-pak listed factory built chimney section at least 12” (304 mm) long, with insulation of 1” (25.4 mm) or more, and an inside diameter of 8” (2 inches [51 mm] larger than the 6” [152.4 mm] chimney connector). Use this as a pass-through for a minimum 24-gauge single wall steel chimney connector. Keep solid-pak section concentric with and spaced 1” (25.4 mm) off the chimney connector by way of sheet metal support plates at both ends of chimney section. Cover opening with and support chimney section on both sides with 24 gage minimum sheet metal supports. See that the supports are fastened securely to wall surfaces on all

sides. Make sure fasteners used to secure chimney flue line.

NOTES:

1.Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the wall pass-through system and the chimney wall, to but not past the inner flue liner face.

2.A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a floor, or ceiling.

14

Ussc

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Improper Installation Could Void Your Warranty Model 3000 L, LNCongratulations Warranty Information Card UsscUnited States Stove Company Box South Pittsburg, TN Firebrick Configuration Flue Collar AssemblyRoom Air Deflector Assembly Assembly Instructions Blower AssemblyPositioning the Stove InstallationSafety Notice Floor Protector Model Front Sides RearClearances to Combustibles ModelChimney Connector Stove Pipe Chimney Factory Built Chimney Masonry Chimney Combustible Wall Chimney Connector Pass-Throughs Outside Combustion AIR BTU’s/CORD Testing Your WoodWoodstove Utilization Heating First FiresIgnition Reloading To Prevent Creosote Build UPGlass MaintenanceASH Disposal GasketingRepair Parts For Models with Legs Key Part No How to order repair parts Ussc Ussc Détachées pièces des commander comment Joints Cendres DES ÉliminationPeinture VitreAvertissements An par fois uneFeux Premiers LES Extérieure température la et laltitudeBois À Poêle DU Utilisation Bois Votre TesterExtérieur Combustion DE AIR Remarques Maçonnerie EN Cheminée Poêle AuUsine EN Fabriquée Cheminée Avec dégagements les ConsulterCheminée PiedsPlissé Tuyau Cheminée DE Raccord Combustibles Matières LES Avec Dégagements ModèleSOL DE Protecteur Arrière Côtés Avant ModèleSoufflante dune linstallation par facilitée Poêle LE PositionnerDassemblée Instructions Pièce la de collecteur du Assemblage Buse la de Assemblage AssemblageTN Pittsburg, South Box .O.P Company Stove States United Garantie DE Carte Félicitations Propriétaire au destiné dutilisation Manuel

3000 (L) specifications

The United States Stove Company 3000 (L) is a powerful and efficient wood-burning stove designed to deliver reliable heat with modern features. Recognized for its robust construction, the 3000 (L) reflects a commitment to quality that has made United States Stove a staple in the heating industry for decades.

One of the standout features of the 3000 (L) is its large firebox. This design allows for extended burn times, accommodating bigger logs that can provide continuous warmth throughout the night. With a firebox capacity of up to 3.5 cubic feet, users can enjoy fewer reloads while still benefiting from an impressive heat output. The estimated heating capability of the stove is around 2,000 square feet, making it suitable for medium to large-sized homes.

Equipped with an efficient air wash system, the 3000 (L) promotes cleaner combustion while minimizing creosote buildup within the chimney. This system optimizes airflow, ensuring that the fire burns hotter and cleaner, thus improving efficiency. Furthermore, the stove is designed to achieve EPA-certified emissions standards, making it an environmentally responsible choice for wood heating.

Incorporating advanced technologies, the United States Stove 3000 (L) features a multi-fuel capability, allowing it to burn various types of fuel, including wood, coal, and pellets, enhancing its versatility. The stove boasts a heavy-duty cast iron door that not only provides durability but also allows for an attractive view of the fire, creating a warm ambiance in any living space.

The 3000 (L) also includes adjustable air control settings, allowing users to fine-tune their heating experience according to their preferences. The built-in ash pan simplifies cleanup, making maintenance hassle-free and convenient for everyday use.

With its combination of efficiency, capacity, and advanced features, the United States Stove 3000 (L) serves as an excellent heating solution for those looking to enhance their home’s comfort. It embodies a blend of traditional craftsmanship and modern technology, ensuring longevity and reliability. Whether you are heating a cozy cabin or a family home, the 3000 (L) stands out as a leading option in the world of wood-burning stoves.
Top Page Image Contents