Installation

Please see all methods of Installation in Appendix at the rear of this booklet.

This is a furnace, not a free standing stove. You must direct heated air from 8" outlets away from the furnace, or it will not function properly.

1.This installation must be done by a qualified heating equipment installer.

2.The installation is to be done in compliance with National Fire Protection Association installation

standards: No. 89M, 90B, 211, 70 (National Elec- trical Code) and Uniform Mechanical Code 913, 6-4, in the states where applicable. (Their code offers connecting smoke pipe connectors into chimney with other fuel burning appliances.)

3.Rooms large in comparison with size of the appliance:

a)Wood or Coal Burning Furnace needs air for combustion and circulation to house.

b)Provision must be made to make up this air and not starve gas or oil furnace of combustion air.

c) Have "Authority Having Jurisdiction"	de-
termine that air is of adequate makeup.	(Refer-

ence N.F.P.A. Nos. 30&54, Code for Installation of Gas & Oil Equipment).

4.Have "Authority Having Jurisdiction" is to inspect all chimneys and installations for adequate venting and for compliance with standard and local codes and regulations regarding installation of wood burn- ing appliances.

5.Installation for Supplemental Heat Application to Existing Central System. (See Fig. 2 for typical installation.)

a)Place Wood or Coal Burning Furnace so that the chimney connector will be as short as practical and avoiding unnecessary sharp turns in the smoke pipe connector and the installation of devices that would create excessive resistance to the flow of flue gases.

b)Locate the Wood or Coal Burning Furnace as close as practical to the existing central hot air heating system, maintaining clearances as stated on the label on the fuel door.

c)Clearance from combustible materials must comply with those stated on the label on the fire door:

Unit to combustible:

Front: 48"

Back: 30"

Sides: 12"

Plenum to Ceiling: 6"

Pipe to combustible: Sides: 21"

Back: 18"

The installation must be made only on a noncombustible floor.

d)Install the smoke pipe connector to the chimney with 26-gauge pipe and elbows (to be purchased separately), maintaining the proper clearances for the specific model. Seal the smoke pipe in the chimney with furnace cement. (The chimney connector shall be securely supported, and joints fastened with sheet metal screws or rivets.)

e)Install 8" diameter heat pipe to plenum of the central hot air furnace. Use 26-gauge pipe and connectors (to be purchased separately). (See Fig. 15) If central air conditioning is installed in the plenum, install heat pipe above the air conditioning unit. Secure heat pipe connection with supports and sheet metal screws.

f)Connect electrical supply in the electrical junction box that is mounted on the back of the Furnace. See Wiring Diagram (Fig. 11). Remove the cover from electrical junction box and connect power supply wires to wires designated, using wire nuts. The power cord supplied may be used for installation, if permitted by local codes and regulations. If the power cord supplied cannot be used, the power supply wiring must be 90 degrees centigrade in a metal cable and should be completed by a qualified installer complying with NFPA Standard No. 70 and local codes.

g)Optional Plenum Fan Control Switch (Part No. 11PCS) is available for installation on the plenum of central hot air heating furnace. The purpose of this switch is to activate the circulating fan of the central hot air heating furnace when the temperature in the plenum exceeds 120 degrees F., and shut off the fan when the temperature in the plenum is reduced to 100 degrees F. This avoids overheating the plenum.

The electrical supply for operation of this fan control switch is to be obtained from the same electrical supply as the central hot air heating system. Follow the instructions of the wiring diagram (Fig. 11). Do not make connections across Limit Control in the furnace.

Make electrical wire connections in accordance with NFPA Standard No. 70 and local codes in the power supply junction box (See Fig. 13). The wiring to complete the connections should be 18 AWG minimum copper and 90 degrees centigrade in a cable.

1537M specifications

The United States Stove 1537M is a remarkable wood-burning stove that combines efficiency, aesthetic appeal, and modern features. Designed for residential heating, this model is particularly suited for medium-sized spaces, making it a popular choice among homeowners seeking an economical and environmentally friendly heating solution.

One of the primary features of the United States Stove 1537M is its impressive heating capacity. It can effectively heat areas up to 1,500 square feet, ensuring warmth during the cold winter months. The stove utilizes a large firebox that can accommodate logs up to 18 inches long, allowing for longer burn times and reduced need for frequent reloading.

The 1537M incorporates advanced technologies to maximize combustion efficiency and minimize emissions. It is equipped with a secondary combustion system that ensures that any unburned gases are ignited in the upper part of the firebox. This not only increases the heat output but also reduces the amount of creosote buildup in the chimney, enhancing safety and maintenance ease.

The stove features a built-in thermostat control, enabling users to regulate the interior temperature easily. Additionally, it boasts an air wash system designed to keep the glass door clear, offering a beautiful view of the flames while enhancing visibility and ambiance in any room.

Constructed with robust materials, the United States Stove 1537M is built to last. Its durable steel body ensures long-term usage, while the cast iron door provides a traditional look with the added benefit of durability and heat retention. The attractive design features a classic black finish, blending seamlessly with various home interiors.

Moreover, this model prioritizes user comfort and convenience. It includes a large loading door for easy access to the firebox, allowing for stress-free loading of wood. Cleaning is also straightforward, with a removable ash pan that simplifies the disposal of ashes.

In summary, the United States Stove 1537M stands out as a top-quality wood-burning stove that effectively combines functionality, efficiency, and aesthetic appeal. With its advanced combustion technologies, substantial heating capacity, and ease of use, this stove is an excellent investment for those looking to enhance their home heating solutions while maintaining a cozy and inviting atmosphere.