HP w1707 17-inch, w1907 19 inch LCD Monitor Quality and Pixel Policy, Power Cord Set Requirements

Page 52

Technical Specifications

LCD Monitor Quality and Pixel Policy

The HP LCD Monitor uses high-precision technology, manufactured according to high standards, to help guarantee trouble-free performance. Nevertheless, the display may have cosmetic imperfections that appear as small bright or dark spots. This is common to all LCD displays used in products supplied by all vendors and is not specific to the HP LCD Monitor. These imperfections are caused by one or more defective pixels or subpixels.

■A pixel consists of one red, one green, and one blue subpixel.

■A defective whole pixel is always turned on (a bright spot on a dark background), or it is always off (a dark spot on a bright background). The first is the more visible of the two.

■A defective subpixel (dot defect) is less visible than a defective whole pixel, and is small and only visible on a specific background.

To locate defective pixels, the monitor should be viewed under normal operating conditions and in normal operating mode at a supported resolution and refresh rate, from a distance of approximately 50 cm (16 inches).

We expect that, over time, the industry will continue to improve its ability to produce displays with fewer cosmetic imperfections, and we will adjust guidelines as improvements are made.

For more information about your HP LCD Monitor, refer to the HP Web site at: http://www.hp.com/support

Power Cord Set Requirements

The monitor power supply is provided with Automatic Line Switching (ALS). This feature allows the monitor to operate on input voltages between 100–240Vv, 50/60 Hz, 1.5A.

The power cord set (flexible cord or wall plug) received with the monitor meets the requirements for use in the country/region where you purchased the equipment.

If you need to obtain a power cord for a different country/region, you should purchase a power cord that is approved for use in that country/region.

The power cord must be rated for the product and for the voltage and current marked on the product’s electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the cross-sectional area of the wire must be a minimum of 0.75 mm² or 18AWG, and the length of the cord must be between 4.94 ft. (1.5 m) and 12 ft. (3.6 m). If you have questions about the type of power cord to use, contact your HP-authorized service provider.

A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.

B–12

User’s Guide

Page 51 Page 53
Image 52
Page 51 Page 53
Contents User’s Guide USA Notational Conventions User’s Guide Contents Troubleshooting Technical Specifications Operating the MonitorPreparing the Monitor for Shipping Agency Regulatory NoticesFeatures Product FeaturesHP LCD Monitors Base Designs Important Safety Information Safety and Maintenance GuidelinesSafety Precautions Maintenance Guidelines Cleaning the MonitorSetting Up the Monitor Installing the MonitorInstalling on a Desktop Unpacking the MonitorUnfolding the double-hinged monitor Assembling the cantilever base Assembling the column baseWall-Mounting the Monitor Mounting Fixture not Supplied Preparing the double-hinged monitor for wall-mountingPreparing the cantilever-base monitor for wall-mounting Reinstalling the desktop pedestal and base for the monitor Preparing the column-base monitor for wall-mountingConnecting the VGA Analog or DVI-D Digital Cable Connecting the Hdmi CableTo connect the VGA cable To connect the DVI-D cableAudio and Video Cables and Adapters Cable/Adapter Name DescriptionConnecting the USB Hub Cable Connecting the Audio CableConnecting USB Devices to the Monitor Connecting the Power Cable Connecting the power cableCable Management Adjusting the Tilt Adjusting the Swivel Select Models Only Adjusting the Height Select Models OnlyPivoting the Monitor Select Models Only Ambient Light Sensor Select Models Only Keyboard ParkingSetting Up the Monitor Installing Drivers Using the Auto-Adjustment FunctionDownloading Updated Drivers from the Internet Operating the MonitorSelect Open Auto-Adjustment Software My Display SoftwareUsing the Onscreen Display OSD Front-Panel ControlsOSD Menu Selections Main Menu Icon Options Submenu Options DescriptionIcon Main Menu Submenu Options Description Sets your own blue color levelsTop Adjusting Screen Quality Selecting Video Input ConnectorsIdentifying Monitor Conditions High-Bandwidth Digital Content Protection Hdcp Power-Saver FeatureOptimizing Analog Video Removing the Monitor Base Preparing the Monitor for ShippingRemoving the cantilever base Removing the column base Removing the column baseFolding the Double-Hinged Monitor Preparing the Monitor for Shipping Solving Common Problems TroubleshootingProblem Solution Locating the Rating Label No Plug and PlayTechnical Specifications Specifications Model vp15Specifications Model vp17 Model vp19Specifications Model FP1707 Model WF1907Specifications Model w1707 Model w1907Specifications Model w2007 Model w2207Specifications Model w2216 Model w2408Preset Video Modes W1707 supports preset modes 1 throughWF1907 and w1907 support preset modes 1 through W2007 supports preset modes 1 through W2216 supports preset modes 1 through W2408 supports preset modes 1 through Power Cord Set Requirements LCD Monitor Quality and Pixel PolicyAgency Regulatory Notices Federal Communications Commission NoticeModifications CablesMaterials Disposal Canadian NoticeAvis Canadien European Union Regulatory NoticeKorean Notice EPA Energy Star Compliance HP Recycling Program#$%&*+
Related manuals
Manual 1 pages 51.46 Kb Manual 1 pages 27.92 Kb Manual 1 pages 107 b
Top Page Image Contents