HP L1950g 19-inch manual Identifying Monitor Conditions

Page 39

Identifying Monitor Conditions

Special messages will appear on the monitor screen when identifying the following monitor conditions:

●Input Signal Out of Range—Change resolution setting to 1280 x 1024 – 60Hz—Indicates the monitor does not support the input signal because the resolution and/or refresh rate are set higher than the monitor supports (models L1950/L1950g, L1750, L1910 and L1710).

●Input Signal Out of Range—Change resolution setting to 1440 x 900 – 60Hz—Indicates the monitor does not support the input signal because the resolution and/or refresh rate are set higher than the monitor supports (models L1908w, L1908wm, L1945w, and L1945wv).

●Input Signal Out of Range—Change resolution setting to 1680 x 1050 – 60Hz—Indicates the monitor does not support the input signal because the resolution and/or refresh rate are set higher than the monitor supports (models L2208w and L2245w/L2245wg).

●Input Signal Out of Range—Change resolution setting to 1920 x 1200 – 60Hz—Indicates the monitor does not support the input signal because the resolution and/or refresh rate are set higher than the monitor supports (model L2445w).

●No Input Signal—Indicates the monitor is not receiving a video signal from the PC on the monitor video input connector. Check to determine if the PC or input signal source is off or in the power saving mode.

●Multiple Inputs are Active—Use the OSD to select the desired video input—(select models) Indicates the monitor is connected to two video inputs. The monitor is trying to display both inputs, but after 10 seconds the monitor uses the default signal input.

●Auto Adjustment in Progress—Indicates the auto-adjustment function is active.

●Monitor Going to Sleep—Indicates the screen display is entering a sleep mode.

●Check Video Cable—Indicates the video cable is not properly connected to the computer.

●OSD Lockout—The OSD can be enabled or disabled by pressing and holding the Menu button on the front panel for 10 seconds. If the OSD is locked, the warning message OSD Lockout displays for ten seconds.

◦If the OSD is locked, press and hold the Menu button for 10 seconds to unlock the OSD.

◦If the OSD is unlocked, press and hold the Menu button for 10 seconds to lock the OSD.

●Power Button Lockout—Indicates the power button is locked. If the power button is locked, the warning message Power Button Lockout displays.

◦If the power button is locked, press and hold the power button for 10 seconds to unlock the power button function.

◦If the power button is unlocked, press and hold the power button for 10 seconds to lock out the power button function.

Identifying Monitor Conditions 31

Page 38 Page 40
Image 39
Page 38 Page 40
Contents User Guide Page About This Guide Iv About This Guide Table of contents Appendix a Troubleshooting Appendix D LCD Monitor Quality and Pixel Policy Viii HP LCD Monitors Product FeaturesPage Important Safety Information Safety and Maintenance GuidelinesMaintenance Guidelines Cleaning the MonitorShipping the Monitor Unfolding the Double-Hinged Monitor Pedestal Base Setting Up the MonitorUnfolding the Single-Hinged Monitor Pedestal Base 3Unfolding the Monitor Pedestal Base Setting Up the MonitorComponent Function Rear ComponentsDVI Cable Management 7Using the Cable Management Feature Double-Hinged BaseConnecting the Cables Page 10Connecting the Power Cable Adjusting the Monitor13Adjusting the Height Adjusting the Monitor 14Pivoting the Monitor Turning on the MonitorUsing the Accessory Rails Connecting USB DevicesRemoving the Monitor Pedestal Base Mounting the Monitor Page Page Locating the Rating Labels 22Locating the Rating Labels Setting Up the MonitorImage Color Matching File Operating the MonitorSoftware and Utilities Information FileDownloading from the Worldwide Web Installing the .INF and .ICM FilesUsing the Auto-Adjustment Function Installing from the CDPage 1Monitor Front Panel Controls Front Panel ControlsUsing the On-Screen Display Menu Adjusting the Monitor SettingsOSD Menu Selections 2OSD Menu Depending on monitor model, factory default is On or Digital DVI Selects DVI input Optimizing Digital Conversion Using the HP Display Assistant UtilityIdentifying Monitor Conditions Sleep Timer Mode SRGB Support Installing the HP Display LiteSaver Software3HP Display LiteSaver Configuration Options HP Display LiteSaverInstalling the sRGB ICM File for Microsoft Windows Vista Changing the Color TemperatureSolving Common Problems TroubleshootingAppendix a Troubleshooting Using the Worldwide Web Preparing to Call Technical Support Technical Specifications Table B-1L1750 SpecificationsL1750 Model L1950/L1950g Model Table B-2L1950/L1950g SpecificationsL1710 Model Table B-3L1710 SpecificationsL1910 Model Table B-4L1910 SpecificationsL1908w Model Table B-5L1908w SpecificationsL1908wm Model Table B-6L1908wm SpecificationsL1945w Model Table B-7L1945w SpecificationsL1945wv Model Table B-8L1945wv SpecificationsL2208w Model Table B-9L2208w SpecificationsL2245w/L2245wg Model Table B-10L2245w/L2245wg SpecificationsL2445w Model Table B-11L2445w SpecificationsL1750, L1950/L1950g, L1710, and L1910 Models Recognizing Preset Display ResolutionsTable B-12Factory Preset Modes Table B-13Factory Preset ModesL2208w and L2245w/L2245wg Models Table B-14Factory Preset ModesL2445w Model Table B-15Factory Preset ModesEntering User Modes Energy Saver FeatureCables Agency Regulatory NoticesFederal Communications Commission Notice ModificationsCanadian Notice Avis CanadienEuropean Union Regulatory Notice Japanese Notice Korean Notice Power Cord Set Requirements Japanese Power Cord RequirementsGerman Ergonomics Notice Product Environmental Notices Energy Star ComplianceMaterials Disposal Chemical Substances Restriction of Hazardous Substances RoHS 11363-2006 LCD Monitor Quality and Pixel Policy
Top Page Image Contents