ASRock 970 Extreme3 manual ASRock Smart Remote Installation Guide, CIR sensors in different angles

Page 24

2.7 ASRock Smart Remote Installation Guide

ASRock Smart Remote is only used for ASRock motherboard with CIR header. Please refer to below procedures for the quick installation and usage of ASRock Smart Remote.

Step1. Find the CIR header located next to the USB 2.0 header on ASRock motherboard.

USB 2.0 header (9-pin, black)

CIR header (4-pin, gray)

Step2. Connect the front USB cable to the USB 2.0 header (as below, pin 1-5) and the CIR header. Please make sure the wire assignments and the pin assignments are matched correctly.

USB_PWR

P-

P+

GND DUMMY

GND

IRTX

IRRX

ATX+5VSB

Step3. Install Multi-Angle CIR Receiver to the front USB port. If Multi-Angle CIR Receiver cannot successfully receive the infrared signals from MCE Remote Controller, please try to install it to the other front USB port.

3 CIR sensors in different angles

1.Only one of the front USB port can support CIR function. When the CIR function is enabled, the other port will remain USB function.

2.Multi-Angle CIR Receiver is used for front USB only. Please do not use the rear USB bracket to connect it on the rear panel. Multi-Angle CIR Receiver can receive the multi-direction infrared signals (top, down and front), which is compatible with most of the chassis on the market.

3.The Multi-Angle CIR Receiver does not support Hot-Plug function. Please install it before you boot the system.

* ASRock Smart Remote is only supported by some of ASRock motherboards. Please refer to ASRock website for the motherboard support list: http://www.asrock.com

24

Image 24
Contents Extreme3 Copyright Notice DisclaimerContents Uefi Setup Utility Package Contents IntroductionSpecifications Connector Bios FeatureRear Panel I/O USBUnique Feature HardwareMonitor CertificationsPage Page Page Motherboard Layout 21.8cm 8.6-inI/O Panel LAN Port LED IndicationsTable for Audio Output Connection Page Installation Pre-installation PrecautionsCPU Installation Installation of CPU Fan and HeatsinkInstallation of Memory Modules Dimm Dual Channel Memory ConfigurationsInstalling a Dimm Installing an expansion card Expansion Slots PCI and PCI Express SlotsPcie Slots CrossFireXTM and Quad CrossFireXTM Operation Guide CrossFire Bridge Driver Installation and Setup For Windows XP OSFor Windows 7 / VistaTM OS Surround Display Feature \ Surround Display InformationASRock Smart Remote Installation Guide CIR sensors in different anglesJumpers Setup DescriptionOnboard Headers and Connectors Serial ATA3 ConnectorsConsumer Infrared Module Header Chassis Speaker Header Supply to this connector ATX 12V Power ConnectorHdmispdif Header Hdmispdif header, providing Serial ATA3 SATA3 Hard Disks Installation What is Hot Plug Function?What is Hot Swap Function? Hot Plug and Hot Swap Functions for SATA3 HDDsSATA3 HDD Hot Plug Feature and Operation Guide Points of attention, before you process the Hot PlugHow to Hot Plug a SATA3 HDD Driver Installation Guide Installing Windows XP / XP 64-bit With RAID FunctionsSet up Uefi Use RAID Installation Guide to set RAID configuration \ RAID Installation GuideInstalling Windows XP / XP 64-bit Without RAID Functions Untied Overclocking Technology Uefi Menu Bar Navigation Keys Main ScreenTo jump to the Exit Screen or exit the current screen System Time HourMinuteSecondOC Tweaker Screen Dram Configuration Dram Frequency AMD Turbo Core TechnologyAMD IO C-State Support Processor Maximum FrequencyPower Down Enable RAS# to CAS# Delay tRCDCommand Rate CR Write Recovery Time tWRWould you like to save current setting user defaults? Four Activate Window tFAWVoltage Control Dram Voltage NB VoltageAdvanced Screen Instant FlashCPU Configuration Cool ‘n’ QuietSecure Virtual Machine Enhance Halt State C1ENorth Bridge Configuration Primary Graphics AdapterSouth Bridge Configuration Storage Configuration Sata ModeSata IDE Combined Mode Sata ControllerSuper IO Configuration Serial PortSerial Port Address Infrared PortAcpi Configuration Acpi Hpet table USB Configuration USB 2.0 ControllerUSB 3.0 Controller Legacy USB SupportCPU Fan 1 & 2 Setting Chassis Fan 1 SettingChassis Fan 2 Setting Chassis Fan 3 SettingBoot Screen Security Screen Exit Screen Install Operating System Support CD InformationRunning The Support CD Drivers MenuInstalling OS on a HDD Larger Than 2TB in Ahci Mode Installing OS on a HDD Larger Than 2TB in RAID Mode Drv4E CtrlB5 LangengChoose Usable Physical Drive List to select Raid HDD Page Windows VistaTM 64-bit Page Windows 7 64-bit